Question about Plymouth Cars & Trucks

1 Answer

Does starter need to be dropped to install oil sending unit on 1995 plymouth voyager

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 197 Answers

No just take one of the battery cables off of terminal :)
replace unit and then replace cable .... always remove the positive cable before the earth

Good Luck

Posted on May 07, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes slow starting when hot on a 1995 Plymouth grand voyager. Replaced fuel pump. Starts fine when cold.


slow starting I`m guessing you mean turns over slowly. you may have a starter motor problem that will need replacing,

Jul 08, 2014 | 1995 Plymouth Voyager

1 Answer

Where is oil pressure sending unit on a 2000 plymouth voyager minivan


please ask a american mechanic as i have no idea ,i would look on the cylinder bolck along a line with the oil gallery but as to where and on what side of the engine no idea but look carefully and you will see it .

Feb 17, 2012 | 2000 Plymouth Voyager

1 Answer

Oil light comes on and off when my 2000 plymouth voyager is just sitting still.


low oil , low oil pressure , bad oil sending unit ( very common) or bad conection at sending unit.

Jan 10, 2011 | 2000 Plymouth Voyager

1 Answer

I need to know where the oli sending unit is and how to replace it?


zjlimited_305.jpg

Fig. 1: Location of the oil pressure switch-3.3L and 3.8L engines


zjlimited_306.jpg

Fig. 2: Location of the oil pressure switch-3.0L engine


zjlimited_307.jpg

Fig.: Oil pressure switch (sending unit) schematic


The low oil pressure warning lamp will illuminate when the ignition switch is turned to the ON position without the engine running. The lamp also illuminates if the engine oil pressure drops below a safe oil pressure level. To test the system, perform the following:

  1. Turn the ignition switch to the ON position.
  2. If the lamp does not light, check for a broken or disconnected wire around the engine and oil pressure sending unit switch.
  3. If the wire at the connector checks out OK, pull the connector loose from the switch and, with a jumper wire, ground the connector to the engine.
  4. With the ignition switch turned to the ON position, check the warning lamp. If the lamp still fails to light, check for a burned out lamp or disconnected socket in the instrument cluster.

REMOVAL & INSTALLATION
On the 2.4L engine, the oil pressure switch is located on the side of the engine block facing the firewall. On the 3.0L engine, the oil pressure switch is located on the oil filter adapter housing, next to the starter motor. On the 3.3L and 3.8L engines, the oil pressure switch is located next to the oil filter.
  1. Locate the oil pressure sending unit on the engine.
  2. Disconnect the negative battery cable.
  3. Disconnect the pressure switch electrical harness.
  4. Using a pressure switch socket, deep-well socket or wrench, loosen and remove the pressure switch from the engine.
To install:
  1. Install the pressure switch into the engine and tighten securely.
  2. Attach the electrical connector to the switch.
  3. Connect the negative battery cable.
  4. Start the engine, allow it to reach operating temperature and check for leaks.
  5. Check for proper oil pressure switch operation.

Hope this helps (remember to rate this answerr).



Dec 22, 2010 | 1999 Plymouth Voyager

1 Answer

How can i fix my 1999 plymouth voyager if the oil light is on but it has oil in it?


You should infact confirm it has proper oil pressure. For this you'll need to remove the oil pressure sending unit and install a gauge; start the engine and check the pressure. If you have none shut it down and repair before running. If the pressure is good (probably 50PSI or so with a cold engine) I'd replace the oil light sender unit. At times these do fail in a closed position giving you a false low oil pressure light. If the engine has very high mileage on it, it may be do to the fact of worn bearings and increased clearances, this too, with a worn pump, will lower the oil pressure
I hope this may have assited you,
Tom

Oct 20, 2009 | 1999 Plymouth Voyager

1 Answer

1998 Plymouth Voyager oil pressure sensor


its probable the oil sending unit and they arent expensive...

Jan 21, 2009 | 1988 Plymouth Voyager

1 Answer

1995 plymouth voyager


check the conections on the starter & maybe remove the starter to check the solaniod & bushes if no good replce the sarter motor .
many thanks lee.

Jan 03, 2009 | 1995 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...