Question about Cars & Trucks

Open Question

2001 swift headlights blink on low beam and sometimes go out momentarly only on low not on bright

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76649 Answers

SOURCE: I have no low beam headlights, high beams are delayed.

Most likely the multifunction switch is defective

Posted on Oct 29, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: My low beams work on my headlights but my High beams wont come on

Take a look at this link regarding DRL system. I know it's not exact truck but most of it would apply to yours too. It should give you hints on what to test & how.
http://www.fordf150.net/howto/drl.php

Posted on Mar 28, 2009

adeel126
  • 60 Answers

SOURCE: low beam headlight on 2001 benz s430 does not

Check the fuse box and according to the printed diagram, check the fuse for the headlights, hope this will solve the problem

Posted on Sep 19, 2009

  • 1986 Answers

SOURCE: HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

  • 26 Answers

SOURCE: Headlight low beans don't work. High beams do

check your fuse box on the inside is a diagram of all fuses check the one that says low beams could be blown

Posted on Dec 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Headlights wont work on dim, only bright


Check your head light bulbs, your truck has the dual filiment headlight bulbs one per side which does both high beam and low beam, 9007 bulbs.
If the low beam filiments are burned out only the high beam will work.
Also look into finding out if the headlight switch is gone bad.
The headlight module and or drl module maybe defective.

Jan 24, 2014 | 1996 Ford Ranger SuperCab

2 Answers

Dim headlights not working on a 2001 taurus bright lights work


you could have a bad dimmer switch not working on the low beam side of the switch.are you sure the low beams work or have they blown and you didn`t notice.

Jun 22, 2011 | Ford Taurus Cars & Trucks

1 Answer

Does this model use a 4 headlight bright system? I have 2 low beam lights but when I put on the bright lights the 2 low beam lights go out and only the 2 bright lights stay on.


I think that many 1990s and even some 1980s GM vehicles with seemingly 4 headlight systems actually use only 2 at a time.

My 1990 Oldsmobile Cutlass Calais, for instance, had 2 high beams that went on independently of the 2 low beam lights when switched with the turn signal lever.

In the 1970s the GM vehicles had 4 headlight systems where all 4 headlights would go on, but they used sealed beams rather than the capsule lights that are used nowadays.

For instance, our 1976 Cadillac Seville has a 4 headlight system that lights up 4 headlights on the high beam mode.

Good luck on seeing at night with the current set up.

Dec 09, 2010 | 1992 GMC Sierra

2 Answers

My headlight just stopped working. One of my


dont replace the bulbs ...check the fuses first...each circuit has its own independent fuse...one for low beam one for high beam and a separate low voltage one for running lights...you may have 1 bad bulb at very worst that could have blown the fuse...why spend extra money on 2

Sep 28, 2009 | 2001 Chevrolet Cavalier

1 Answer

2001 honda civic dim headlights will not come on just brightlight


Low beams are separate bulbs and could possibly both be burnt out

Apr 04, 2009 | 2001 Honda Civic

2 Answers

NO High Beams only Low Beams..


When I try to use the high beams on my 2003 buick century they will not stay on when I let go of the lever and when I do let go of the lever sometimes my headlights will all go out. I just gave up on using the high beams at all

Mar 02, 2009 | 2001 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...