Question about Cars & Trucks

Open Question

What is my current point balance - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I know my balance.


Stand on one leg and see how long it takes before you need to put the other leg down.

May 06, 2017 | Cars & Trucks

1 Answer

Trying to check my Kroger fuel points but get too many pop ups and no information. Web site is useless.


There is often a small link at the bottom of the screen saying 'Send Feedback'. and here you go, there is. I get no pop ups :>)

I found this about Fuel Points.
How do I keep track of my fuel points?

Your current fuel points balance is located at the bottom of your Kroger receipt. You may also
Customer Service

Dec 04, 2016 | Cars & Trucks

1 Answer

1996 Honda Accord harmonic balancer is rubbing the car frame


first point to check is the engine mounts
if they are at the bottom of the insulator , that will be allowing the pulley to touch the frame
replace all engine mounts
next point is the harmonic balancer itself
make sure that it is properly set in position and if it has a rubber section between pullet and crank hub, check that it is in line
if it is not replace the harmonic balancer
At this point , the engine mounts would be a fair bet because of the age of the vehicle
that is unless the vehicle has been involved in an accident and the frame was not straightened or positioned correctly

Feb 25, 2016 | Honda Cars & Trucks

2 Answers

I have a 99 expedition I had the tires changed I put smaller tires on it to get rid of the mud tires now my front end shakes like it has 2 flats


more than likely there is some component damage ,linkages, tire rod ends, vibration dampener the shock looking thing under front end , connecting left to right on steering link.

Feb 22, 2015 | 1999 Ford Expedition

2 Answers

I have a 1994 nissan 2.4L pickup.I am currently in the process of changing the timing chain,cam gear and crank gear. In this process I noticed that the keyway on the crank gear is not in the up posit


Same happened to me. Economic way to ensure its at tdc is to remove #1 plug, using a thin dowel rod mark the distance it travels inside spark plug hole. Turn crankshaft slightly until you can measure the #1 piston is at its highest position. You'll be at tdc.

Jan 29, 2015 | 1994 Nissan Pickup

1 Answer

Dodge dakota 3.9 v6 year 2000 where should rotor point to on cap when cam gear dot at6 and crank gear dot at 12 and on tdc compression stroke it points to number 4 on cap when cam dot at 6 o clock


You'll have to put the timing cover and balancer on to find out if the mark on the balancer is pointing to the mark on the cover. If it is, the rotor should be pointing to cyl 1 plug wire.

Sep 17, 2014 | Cars & Trucks

1 Answer

The car is making a thumping noise like the the rotor is warped or the balance is off but the rotor was replaced today and the tires are balanced


one of your ties could be loosing a tread,, balancing them will not show this up until the tire is actually holding weight and moving down the road, does it change at different speeds? take the car back to whoever you got the tires from, point out the area where the problem is, and ask them to check that tire,, and tell them to test drive it and you go with them to point it out

Jul 07, 2011 | 2006 Chevrolet Cobalt

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

1 Answer

1988 dodge ram 50


Greetings!
Further to Tinkertoys1's note...

Yes, the harmonic balancer is manufactured to only fit on one way.
Now, knowing this, the harmonic balancer has a timing mark set into the outside area of the balancer.

Cheers, Jay

May 18, 2008 | 1988 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...