Question about Cars & Trucks

Open Question

Where can i get a mark 49 softiner rebuilt - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to check is my Hyundai is CA emission or the other 49 states?


How many O2 sensors are the best way. On a 4 cylinder, you are good everywhere. On a 6 cylinder if you have 3 O2 sensors, it is federal, 4 O2 sensors is CA. It should also be marked on the under hood tag. Most don't say CA. But the do say Fed.

Mar 24, 2015 | 2005 Hyundai Tucson GLS

1 Answer

No start. Is the crank out 180?


Normally if your timing mark are at the right place it should start recheck does mark

Mar 11, 2015 | Cars & Trucks

2 Answers

How to Remove headlight cover on 2014 silverado


The headlights do not have covers. They are a complete one-piece lamp assembly.

Jul 13, 2014 | 2014 Chevrolet Silverado 1500

1 Answer

A plane is 48 miles west and 49 miles north of an airport. The pilot wants to fly directly to the airport. What bearing should the pilot take? Answer should be given in degrees and minutes.


Draw the airport. (X marks the spot) Draw the distances from the airport (to scale) to indicate the position of the Plane. Use a protractor to work out the correct angle.

To Calculate:

a=48 b=49 Angle= Tan-1(a/b)

Sep 25, 2013 | Cars & Trucks

1 Answer

Witch slot does the cam gear go on the cam on a 92 camry v6. the 3v mark or the 4v mark.


Go to the library and look it up in Chilton's auto repair manual.

Dec 01, 2011 | 1992 Toyota Camry V6

1 Answer

I took camgears off cams to replace bent valves. Need to know where cam dowel pins go to put camgears back on with engine is at tdc.


Install the camshaft sprockets onto the camshaft. Be sure to align the I mark with the intake camshaft dowel pin and the E mark with the exhaust camshaft dowel pin, then tighten the retaining bolt to 36-44 ft. lbs. (49-61 Nm).

Feb 09, 2011 | 2004 Kia Rio

1 Answer

Trans shutters @ 40mpr had trans @ tork replaced by rebuilt ones now itshutters when we get to approx 49 MPR.


There is an automatic torque converter clutch circuit and sensor that can go bad in these.

Nov 05, 2010 | 2000 Cadillac DeVille

1 Answer

Not sure how to remove a driveshaft from a 91 ext. cab mazda truck B2600


Welcome to FIxYa.com


REMOVAL AND INSTALLATION

Remove in the order shown in the figure. Install in the reverse order of removal.

I Image

1. Nut

2. Lock washer

3. Bolt

4. Nut

5. Nut

6. Lock washer

7. Bolt

8. Nut

9. Washer

lo. Nut

11. Lock washer

12. Bolt

13. Rear propeller shaft
leedavidian_15.pngleedavidian_16.pngleedavidian_17.pngleedavidian_18.png

Propeller shaft (4x2)

Before removing the propeller shaft, mark the flanges for correct installation.

Propeller shaft (4x4)

Before removing the propeller shaft mark on the front, and rear side flanges for correct

installation.

(4x2 Model)

When the propeller shaft is removed from the extension housing, immediately install the

SST into the extension housing to prevent oil leakage

B2200: 490259440

B2600i: 49 5120 440

1m a

Propeller shaft

1. Align the marks. And install the rear propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)

2. Install the center bearing support assembly.

Tightening torque: 36-53 N.m 3.7-5.4 m-kg, 27-39 ft-lb)

3. Align the marks, and install the front propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)


Thank you for using FixYa.com

Regards, Lee Davidian

Nov 05, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

Torquing head


The 98 Corolla has a "torque-to-distance" spec.

First, torque all 10 bolts to 36 ft lbs (49 NM or 500kgf-cm), in a clockwise fashion, starting with the 2 center bolts.

Second, mark the bolts with a paint mark, and then torque each of the 10 bolts an additional 90 degrees.

Hope this helps, and thanks for choosing FixYa.

Nov 15, 2008 | 1998 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...