Question about Cars & Trucks

Open Question

Clark forklift C15 error is oil pressure is opened check it. I don t understand the opened part.

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 13771 Answers

SOURCE: Old Clark forklift will not fire

Or propane ?

Posted on Aug 16, 2015

  • 391 Answers

SOURCE: Clark forklift will not fire

Remove the distributor cap, remove the rotor, turn the ignition on, turn the motor until the points (contact breaker) starts to open, you should see a spark, if not, turn off the ignition, check to see if the contact surfaces are flat and not pitted. gap should be 0.35mm (15 thou) adjust if neccessary, clean the contact surfaces with some fine sandpaper. Turn the motor until the points are closed and turn a little more. Turn the igition on. With a small screwdriver, open the pionts without the screwdriver touching anything else. you should see a spark. Replace the rotor & cap. The engine should start provided fuel is getting to the carburettor and the coil is ok. Hope this helps, please comment and avise.

Posted on Aug 16, 2015

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the oil pressure sensor located on a C15 engine

look at the second one.

2010-07-31_202455_oil_pressure_sensor-4ppk1x0uth2ivfa4q5415bd5-3-0.jpg That should get you what you want. By the Oil Filter

Nov 18, 2017 | Cars & Trucks

1 Answer

TCM Forklift model FCG25-3L will not start when i turn the key to the on postion u can hear the fuel coming out of the intake

Danger of hydro-lock or fuel in crankcase condition will occur. Do not start! Fuel pump relay should be interlocked with oil pressure sending unit. Is it diesel or gas? Is it Carb or fuel injection? Investigate before running engine. Check oil dipstick for presence of fuel in oil. Fire hazard also exist .Be careful.

May 22, 2017 | Cars & Trucks

1 Answer

What does fault 108-1 mean on a Yale forklift

Troubleshooting Yale -
No Trans Braking Error code 524264-14. Discussion started: 5 .... Error code 108-1displayed. Discussion ... Yale forklift has perkins 4203.2 engine oil capacity?

Oct 23, 2015 | Cars & Trucks

1 Answer

Clark forklift 3 ton movmenet problem

check hydraulic fluid levels/ filter..also look for any leaks near the valve controls and this a gas powered one or an electric one..

Dec 22, 2013 | Cars & Trucks

1 Answer

I have just rebuilt a mazda va engine out of a forklift. While priming the oiling system I am not able to get more than 10psi. I have checked all the normal stuff as I am a engine machine shop owner and...

how are you priming the system
before installing the oil pump , you fill it with grease or vaseline
That primes the pump so that when you start cranking it it is producing pressure
to get pressure you need volume and there will be no way that you will get the volume required other than by the pump

Dec 16, 2017 | Mazda B-Series Truck Cars & Trucks

1 Answer

My 2004 Pacifica wont start at all, the gear is in park but the gears on my dash panel are all lit up, no matter what gear I put it in. I changed the Transmission Solenoid cause their was a hole in it...

What Transmission Solenoid did you replace ? Pressure control solenoid ? Shift control ? P0522 code is not saying oil pressure is low , It's saying the PCM is seeing sensor pressure low ! Do you know how to test automotive electrical circuits with a volt meter ? An this has nothing to do with your gears lit up . Different problem .

Apr 15, 2017 | Chrysler Pacifica Cars & Trucks

1 Answer

My oil light just came on i check oil is fine no knocks or smells i am about 400 miles till i am due for an oil change could it be an oil pressure switch

First, check the oil level (as you did). If low, add immediately. If car is relatively new, your PVC valve may have stuck open drawing the misted oil to the intake and burning it with very little tell tail smoke, this would resolve missing/low level oil issue. If you don't understand the system, take it to your dealer. You could loose the engine with low oil pressure. Most pressure sensors open at 5PSI turning out the light on your instrument panel.

Feb 19, 2011 | 2006 Kia Spectra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides