Question about Cars & Trucks

1 Answer

How to bleed clutch system from the start for Camry 99 v6 mv 20

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 197 Answers

You have to have 2 people, this is how you do it:

person inside press clutch pedal down
person outside opens bleeder
person outside closes bleeder
person inside pulls clutch pedal up
repeat over and over and over

heres a video - all clutches are pretty much the same to bleed --- https://www.youtube.com/watch?v=YlnlMuYzLRE

Posted on May 06, 2017

Testimonial: "Cheers mate,have tried that,at the start of the process I have accidentally pushed down on clutch pedal and due to that it won't bleed."

  • Adam Plug
    Adam Plug May 06, 2017

    Another option is to reverse bleed the system. Force fluid through the bleeder on the slave into the master.

  • Adam Plug
    Adam Plug May 06, 2017

    other than that your slave cylinder might have spat it perhaps...

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I pushed clutch n while system was open and now Iwe can't bleed clutch system,99 Camry v6 mv20


close of the bleeder nipple
you may have to operate the pedal by hand to pull it op of the floor a few times
open the nipple with the pedal on the floor . close off the nipple while the pedal is down . repeat the process until the air is bled out

May 06, 2017 | Cars & Trucks

1 Answer

Bleed clutch lines on 99 miata manual clutch


Underneath the vehicle there is a clutch slave cylinder that has a bleed port.
bleeding clutch for slave cylinder replacement

Feb 07, 2015 | 1999 Mazda MX-5 Miata

1 Answer

Bleeding brakes on a 1992 camry toyota with a.b.s


Was or IS there air in the system?
Did you let the Master cylinder go dry?
Bad news.
Need to follow the manufacturers bleeding sequence.
Usually RR,LR,LF,RF.
DO NOT LET BRAKE PEDAL GO TO THE FLOOR!!!!!!
It will kill the master cylinder(1992 car).
If it has,the master may be ruined.
Replace it and start over.Follow instructions in the box,but there are easier ways to do it.

I need a LOT more info,here.

Feb 21, 2013 | 1992 Toyota Camry V6

1 Answer

Toyata camry v6 99


You have a ground issue.Current from another circuit is running through the lights to get to ground. this causes them to burn out quickly.You need to do a real detailed visual check.A good component wiring diagram and component locator is a requirement here.

Sep 06, 2012 | Cars & Trucks

1 Answer

No pressure in my clutch 1993 toyota camry


Slave cylinder is in the front you will see brake line going to it.

Nov 28, 2011 | 1993 Toyota Camry V6

2 Answers

1999 Camry Solara: the clutch stays pressed all the way down on its o...


Hello, and welcome to FixYa. Please allow me to assist you.

I had the exact same problem in my V6 Camry. The problem turned out to be bad clutch hydraulic cylinders. I replaced the clutch master cylinder (on the firewall) and the clutch slave cylinder (on the transaxlwe), the problem was eliminated.

Replace your clutch hydraulic cylinders, and you will be fixed right up.

Thanks for choosing FixYa for assistance today.

May 05, 2010 | 1999 Toyota Camry Solara

2 Answers

Car running hot 1993 toyota camry. it has new engine head, new fan, midas did a radiator flush check to see if it was that. checked water pump said no its not the reason the thermator is not in the car...


You should have a thermostat in the engine. It allows the water flow to speed up or slow down as needed. Also, make sure your antifreeze is set for 20° BELOW zero.

Jul 03, 2009 | 1993 Toyota Camry V6

1 Answer

Hyd. Slave cylinder WITHOUT bleeder


you have to replace the master and slave. if there is no bleeder, you might get lucky bench bleeding it, but the whole assy, comes from dealer pre-bled. The system is sealed and even to do a clutch or trans, you shouldnt have to take it apart. DO NOT PUSH CLUTCH WITHOUT ALL PARTS HOOKED UP! youll break it.

Mar 21, 2009 | 1999 Dodge Dakota

1 Answer

Bleeding the clutch


This would be simpler with 2 people. One would sit in the car and the other under it with his wrench on the bleed screw. Have the person inside pump on the clutch pedal several times and then hold it down. The other person then opens the bleed valve on the clutch, let the fluid come out while the person inside is continueing to hold the pedal down. Close off the bleed screw and repeat several times until all the air is gone from the system. If you dont have any leaks, you are good to go. Make sure you service the reservoir, and forget the mechanic.RC

Jan 05, 2009 | 1986 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...