Question about Cars & Trucks

2 Answers

My vx commodore clutch is leaking where the clutch adjustment is on the inside of the car it seems to be leaking out that rubber boot! Why? Is this fixable

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 197 Answers

They tend to leak if the clutch pedal has been adjusted to its maximum - perhaps back it off a bit and see if there's an improvement - don't forget you will need to re-bleed the clutch after adjusting BUT they can be a real pain to bleed!!!
Maybe get a mechanic if too hard but there's plenty about re-bleeding clutches on you tube

Posted on May 06, 2017

Testimonial: "Thanx"

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 51,218 Answers

replace the clutch master cylinder with a new one
if the clutch salve cylinder has been replace in the last 5 years replace it also

Posted on May 06, 2017

Testimonial: "Thanx"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What each colourvwiringis for in vx ,2002,Commodore

The Holden Commodore (VX) is an executive car that was produced by the Australian manufacturer Holden from 2000 to 2002. It was the second iteration of the third generation of this Australian made model. Its range included the luxury variants, Holden Berlina (VX) and Holden Calais (VX), and it formed the basis for a new generation Holden Ute (VU) coup? utility and Holden Monaro (V2) coup?.
The VX series was produced between October 2000 and September 2002, as a minor restyling update to the VT series from 1997. It introduced greater model differentiation along with gains in crash safety. An intermediate Series II was launched in August 2001, featuring a revised suspension system among other changes.



Apr 16, 2017 | Cars & Trucks

1 Answer

Will ls1 go in vx commodore s 2000

yes VX V8s were fitted
depends on what state you live in
LS1 fitted may need a modification plate
needs the LS1 engine ecu and
and a few extra wiring and
join the just commodore forum for loads of helpful information

Jul 29, 2016 | Cars & Trucks

1 Answer

Check transmission trian on Vx commodore executive it had no fluid have filled it but keep getting that message is their a reset button

try this just commodores forum
on the VZ 2004-- 2006
Forum VZ Holden Commodore 2004 2006

I only know of engine service message
clearance using the mode buttons on a VT.VX

i hope you are a lucky person because
any commodore transmission man or auto
driven without fluid would have taken some internal damage


Jun 23, 2016 | Cars & Trucks

1 Answer

How to know if slave cylinder in leaking

In the design of most of them, the slave cylinder is all external to the bell housing, so just peel the rubber boot back to see if it is full of fluid. Similarly for the clutch master cylinder, which could be located inside or outside the firewall.

Mar 15, 2015 | Cars & Trucks

1 Answer

How do I eliminate the loud wind noises coming through closed sunroof? I have a 2002 Holden Vx Ss Series 2 Commodore

sounds like you need new rubber seals, but first, open the roof, and with a damp cloth, clean dirt off the inside rubbers, then close roof most of the way and clean around the edge of the glass/metal, which ever it is. Then close it fully and see if there are any tiny gaps. Does it leak water ? Red.

Apr 04, 2014 | Cars & Trucks

1 Answer


I assume that the clutch isn't releasing. I had an older pickup that the clutch master cylinder was leaking but the rubber boot was keeping the fluid from leaking out so you couldn't see it. Peek at the master and slave cylinders (peel the rubber cup back a bit to check for leaks) and see if that isn't your problem.

Apr 01, 2014 | 1994 Toyota Pickup

1 Answer

Will vx trans fit vs commodore

You will need to check with a salvage yard on this, they have cross reference books to tell them this.

Oct 11, 2012 | Holden Commodore Cars & Trucks

1 Answer

Fuse box diagram for vx commodore

Anything for less than $200 is great.

Jun 05, 2012 | Holden Commodore Cars & Trucks

1 Answer

How to adjust the clutch on 1977 mgb. my clucth is almost on the floor to change gears

There should be just a couple thousands of an inch of free play at the slave cylinder to the fork. (at the bell housing) If you have more than that, then adjust the length of the slave cylinder pin. Your symptoms can also be caused by not enough brake fluid in the clutch master or air in the line. If it gets way better by pumping the pedal you might just need to bleed the air out. If it is leaking fluid at the slave, it needs a new rubber washer inside - a rebuild kit usually includes the dust boot for it also. If it is leaking fluid at the master, rebuild that.

Oct 15, 2011 | Cars & Trucks

1 Answer

Clutch isn't working. feels really loose and i can't figure out how to check any fluid levels

depending on the car, your fluid level resovior for your clutch should either be under your brake MC or side by side, it is easy to tell, your brake MC will have several lines coming from it where as your clutch cyl will only have 1 line, so look for thr one that has only 1 line, also another place to check for a leak is inside the car, follow the clutch pedal to where it connects to the pedal pushrod that comes through the firewall , there should be a rubber boot covering the pushrod , squeeze that rubbr boot if you get wet with brake fluid then it ( the clutch MC) is bad, also check on the trans for brake fliud leaks coming out of the clutch bell housing, n alot of todays cars the slave cyl is internal and operates the clutch release bearing as well instead of a pivot fork style... please rate theis help, thanks...

Aug 05, 2009 | 2005 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides