Question about Dodge Cars & Trucks

Open Question

I have a 2004 Dodge Stratus sxt coupe SOHC 2.4 L. Where is the cam shaft position sensor located and how do I remove it to replace it?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: 2004 Dodge Stratus SXT 2.4L Coupe

its in the intake air hose close to the throttle body

Posted on Oct 08, 2008

ewashmidas
  • 362 Answers

SOURCE: Cant find transmission filter on 2003 Dodge stratus Coupe.

The filter is inside the transmission. You need to take the pan off the bottom then you can replace the filter and the pan gasket.

Posted on Mar 04, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 36 Answers

SOURCE: where spark plugs located on 2004 dodge stratus

Should be an intake plenum under the hood. Remove plenum and they are rite in the top of the head.

Posted on Nov 15, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need torque specs for the head bolts on a 2004

For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Posted on Aug 02, 2010

Testimonial: "I appreciate your quick response. Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Diagram of where a camshaft sensor is on a dodge stratus 2.4L 4 cylinder


2003 model
not confirmed
crank angle sensor might be near the stater motor on the block


26233366-qzmmc3ihqjw1j4mumdlnccct-4-0.gif

26233366-qzmmc3ihqjw1j4mumdlnccct-4-2.gif

Jul 07, 2016 | Dodge Cars & Trucks

1 Answer

2004 dodge stratus 2.4 dohc po344 code


PO 340 thru PO344 are cam shaft position sensor issues

That does not tell you what is wrong or to replace anything

Have it diagnosed at a repair shop

A sensor could fail & it more than likely is just
reporting other issues you have to have resolved.

Oct 02, 2012 | 2004 Dodge Stratus

1 Answer

How do I remove the input/turbine speed sensor? I have the R/T v6 3.0L Coupe


MAKE SURE YOU IGNITION KEY OFF POSITION. YOUR VECHICLE SPEED SENSOR IS LOCATED IN THE INPUT SHAFT HOUSING NEXT TO TWO FLUID COOLING LINES TO REMOVE IT YOU REMOVE ELECTRCAL CONNECTOR FROM FROM THE VSS.THEN REMOVE THE VSS SENSOR OUT OF TRANSAXLE.REPLACE O - RING THEN INSTALL THE NEW VSS OR VECHICLE SPEED SENSOR.

Nov 25, 2010 | 2001 Dodge Stratus

1 Answer

I need torque specs for the head bolts on a 2004 Dodge Stratus Coupe 2.4L SOHC


For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Aug 02, 2010 | 2004 Dodge Stratus

2 Answers

A 2004 Dodge stratus with the 4 cylinder that will not start


code p 16 refers to crankshaft position/cam shaft position bank 1 sensor A--correlation====causes ---wiring---CKP sensor ( crankshaft position sensor )---mechanical fault

code p 0340 refers to -camshaft (CMP) sensor A bank 1 circuit malfunction ===causes wiring--CMP sensor--ECM
cosrs nothing to check the timing belt , just remove the oil filler cap and see if the rockers are moving when turning it over
the clue here may be bewteen the 2 codes , the word correlation and circuit malfunction so check the wiring, harness connections for pin corrosion and then substitute the ECM with a know good unit as the correlarion and circuit malfunction could be in the ECM
if the ECM program is not getting good reports for both sensors then it reasons that the piston and cam shaft are not timed properly and so will not allow it to start

May 15, 2017 | 2004 Dodge Stratus

1 Answer

Where spark plugs located on 2004 dodge stratus coupe sxt


Should be an intake plenum under the hood. Remove plenum and they are rite in the top of the head.

Nov 14, 2009 | 2004 Dodge Stratus

1 Answer

Cam Shaft Sensor Problems


Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Dec 15, 2008 | 2004 Dodge Neon

1 Answer

2004 Dodge Stratus SXT 2.4L Coupe


its in the intake air hose close to the throttle body

Sep 30, 2008 | 2004 Dodge Stratus

1 Answer

2004 dodge stratus with 2.4L


Hi...
The Code P0340 on your Stratus is :
Camshaft Position Sensor Loss signal.
Ok, The first step is check tha condittion on the connector.
For corrosion, bent pins or damaged wires.
If you found that everything is ok.
Replace the Cam Position Sensor.
The Cam Position Sensor, Is common that the Cam fail on this Vehicle and similars of this.
Tha Cam position sensor Is located:
At end of the engine head, driver side. Is attached with 4, 10mm
screw, and the connector at the center of the sensor.

I hope this help on your problem.
Thank you for use fixya...

Aug 29, 2008 | 2004 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...