Question about Cars & Trucks

1 Answer

Only have high beams no low beamsfor both headlights

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,554 Answers

Check the globes. I have had this on a ford falcon EA series where the filaments on low beam had both blown and I only had high beam so worth checking.

Posted on May 05, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While low beams on the left high beams stays on dim light but wen I turn high beams on they work fine


It could be driving lights mode instead of low beam. Check connections.

Jun 16, 2017 | Cars & Trucks

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

1 Answer

No power to right side (PS) headlight low beam plug socket, new bulb, fuse is good. High beam works, blinker works, park light works. just no low beam and doesn't register any voltage on volt meter.


check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

Jan 30, 2014 | Cars & Trucks

1 Answer

1987 Chrysler Fifth Avenue, only one low beam headlight is on.


the light is out replace it the low side work when u have high beams on ththe short in the light is in the low beam .

Sep 09, 2012 | 1987 Chrysler Fifth Avenue

1 Answer

My 2004 madza 3i high and low beam are too low. I have to use high beam to see the road. Is anyone know how to fix it?


This is not hard to fix. Wait until it is dark enough outside to clearly see your headlight beams, then park your car on level ground 20 feet from a wall, fence, garage door, etc. Turn on your headlights (be sure your high beams are off) and open the hood. on the top of each headlight assembly you will find an adjustment screw... just turn the screw with a Phillips screwdriver until the hot spot in the center of your headlight beam hits the wall where it meets the ground.

Nov 22, 2011 | Cars & Trucks

1 Answer

The high beam indicator is on. The low beams don't work.


You need a new headlight dimmer switch located on the steering column between the dash and the firewall

Jun 03, 2010 | 2000 Mazda MPV

1 Answer

Headlight low beam


Test to see if you have voltage at the bulb connector in low beam position. I'd almost bet that if there is no voltage there for the low beams that you have a bad high/low switch.

Oct 03, 2009 | 2002 Subaru Forester

1 Answer

Low beam not work !!


replace the headlight bulbs. Usually when the bulbs blow out the low beam blows out first, but the high beams still work. If you want and need both low and high beams to work then replace the headlight bulbs with brand new ones and I garauntee that both low and high beams will work

Mar 27, 2009 | 1999 Dodge Caravan

2 Answers

What would cause both low beam headlights to go out at the same time? i have replaced the headlights and they still dont work.


The headlight high/low beam switch assembly.96 Safari has the turn signal stem as the high/low beam switch.Removal of the steering wheel is necessary to get to the switch assembly for replacement.

Jul 13, 2008 | 1996 GMC Safari

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...