Question about Cars & Trucks

Open Question

2005 pt cruiser turns over won't start? Oil on the spark plugs!codes 118,113,108... any suggestions??

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75117 Answers

SOURCE: oil light keeps coming on and beeps

This is the pressure light, nothing to do with the oil needing to be being changed, you have low oil pressure being indicated, this will destroy the engine if the light is really indicating low oil pressure, have the oil pressure tested with a mechanical test guage at a shop, if the oil pressure is ok then replace the oil pressure light sending unit.

Posted on Nov 23, 2008

  • 15 Answers

SOURCE: spark plugs

you must take off the in-take housing top of engine ( plastic) 5bolts,take off bolts at throttle body3bolts,take off all hoses in rear of plastic throttle body 2 bolts,take your time not to brake plastic hoses in rear, and make sure you have gaskets inside of plastic intake once you take off. Pull intake off slow, and the spark plugs and wires are seen. You need a spark plug wrench to take out spk plugs, do one at a time. Replacement is the reverse........runjoe

Posted on Mar 02, 2009

66 chrgr
  • 1011 Answers

SOURCE: 2005 pt cruiser misfire low rpm

Have your plugs and wires checked for replacement:)

Posted on Jul 31, 2009

nicole99wu
  • 1049 Answers

SOURCE: My 2005 PT Cruiser shows error codes P0508, P0688,

this obd2 trouble code table can help u understand the meaning of code.
po522, the possible solution:
The most likely cause is a faulty oil pressure sensor/switch.
for p0688, you can Check all the ECM fuses, if the fuses are OK try replacing the ASD relay.

Posted on Aug 15, 2011

emissionwiz
  • 75117 Answers

SOURCE: Where is crank sensor on

REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Posted on Aug 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Pt Cruiser running poor at acceration


If plugs helped...the problem went away...then it could be a plug getting fouled by excess fuel or oil. Look at your new plugs and see if they are discolored or went with gas. could be an injector problem. It could also be an ignition problem. You moved the plug wires around and they worked for a few minutes till the new "connection in the wire" burned up. Check your plug wires with an ohm meter. Check your plugs for fuel or oil on plug...a sign of stuck injector, oil leak, misfire. Did it really help or was it just wishful thinking?

Apr 02, 2014 | 2002 Chrysler PT Cruiser

1 Answer

2005 PT Cruiser showing P0456 and P0522. Cranks but wont start.


The sensor that is most likely causeing the problem is the low oil pressure sensor. It is telling the cpu that you have a problem that unless you correct it, the motor will suffer serious damage from insufficient lubrication.Have the oil pressure checked with a manual gauge then replace the sensor unit if faulty.

Feb 23, 2013 | 2005 Chrysler PT Cruiser

1 Answer

How do i remove intake manifold on 2005 pt cruiser 4 cylinder


there is a 2 part. just take off the one going over the valve cover. it has 6 -10mm bolts

Feb 11, 2013 | 2005 Chrysler PT Cruiser

1 Answer

My 2005 PT Cruiser shows error codes P0508, P0688, and P0522. Sometimes it runs well, and other times it runs rough then dies and won't start back.


this obd2 trouble code table can help u understand the meaning of code.
po522, the possible solution:
The most likely cause is a faulty oil pressure sensor/switch.
for p0688, you can Check all the ECM fuses, if the fuses are OK try replacing the ASD relay.

Aug 15, 2011 | 2005 Chrysler PT Cruiser

2 Answers

Engine light on


They are still looking for a cause because it isnt misfiring right now or because they cant find the cause of the stored misfire codes ?
If it is misfiring right now and they cant figure it out then perhaps you should find new mechanics !
I have seen a lot of bad coils on the PT.
Misfire is usually caused by spark plug wires first, spark plugs 2nd, and coil third.
If it isnt misfiring now, spray down the wires with water. If it misfires after that replace the spark plug wires and spark plugs and try again.
If it still misfires then the problem will likely be the coil.



Oct 03, 2009 | 2005 Chrysler PT Cruiser

1 Answer

2005 pt cruiser... it sputters and won't idle well


That is the first thing i would suggest you do. Replace all the spark plugs and the plug wires. Those 2 things are the most commen thing that cause misfires.

Mar 19, 2009 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...