Question about Ford Ranger

Open Question

2010 ranger codeb1212 new drivers seat

Replaced drivers seat used

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side electric seat is stuck in the far forward position and won't move. How do I move it manually or fix the motor.


Auto Repair: How to Replace a Power Seat Motor - YouTube

? 1:44
https://www.youtube.com/watch?v=EDh-0rs5Fjo
Oct 26, 2010 - Uploaded by automdvideos
Auto Repair: How to Replace a Power Seat Motor ... 2007 - 2008 Ford Expedition/Lincoln Navigator Driver Bottom Install Video ...2003-2006 Chevy/GMC Seat Cover Install 1 of 3 - eBay Ready ...2000 Ford Explorer Front Seat Track Stuck Motor Repair - Duration: 4:39. by cubmancan 4,959 views. 4:39.
Drivers seat is dead! No power seat or heat. - TheDieselGarage.comwww.thedieselgarage.com/.../96465-drivers-seat-dead-no-power-seat-hea...Mar 22, 2010 - 2003-2005 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2003-2005.... Power seat on driver side didn't work.....passenger did! Neither ...DANG electric seat ' Chevy Truck Forum ' GM Truck Clubwww.gmtruckclub.com/forum/threads/dang-electric-seat.2990/Apr 27, 2006 - 10 posts - ‎7 authors'03 Tahoe My driver seat just stopped, of corse not where I need it, the ... I have a 2003Tahoe and both heated seats are not working. ... with my seat heater on the drivers seat in my 03 Avalanche, it turns ... The driver's side on my Silverado gets way warmer than the passenger side. ... Frozen New Member.Power Seat Problems?? - Tahoe Forum - Che

Dec 29, 2015 | 2003 Chevrolet Avalanche

1 Answer

Have a 2010 ford ranger standard cab .the seat belt light goes off with chime, whether buckled up or not. How do I troubleshoot it.


The wire for the light is connected to a switch inside the latch side of the seat belt. It can get knocked loose if you have a lot of stuff under the seat. The switch cab go bad too. That will require replacing just the latch side of the belt, not the entire belt.

Dec 20, 2015 | Ford Cars & Trucks

1 Answer

Heated seat on driver side not working


The heating pad in the seat finally died.
My drivers side did the same thing but i havent gotten around to replacing it yet.
Ebay sells new heating pads if you want to replace it yourself.

Oct 26, 2015 | 2010 Ford Taurus SEL

1 Answer

2010 ford ranger fuel gauge not working has new sender.gauge goes up and then right back down


it can b a bad earth wire or one of the wires not making perfect contact

Jun 12, 2015 | 2010 Ford Ranger 2.3

1 Answer

2010 Ford ranger, slips out of gear (from drive to OD) NO check engine light NO code, New filter and oil ( 2.3 automatic ).


Could be TCC solenoid, sticky valves/ valve body, or torque converter. Could be clutch bands also. Needs to be on a scanner.

May 22, 2015 | 2010 Ford Ranger

2 Answers

Driver seatbelt 2010 toyota matrix wont retract


go to nearest toyota dealer will change that out for free.anything safety related seat belt.

Mar 10, 2015 | 2010 Toyota Matrix Automatic

1 Answer

Show me how to replace the horn fuse in an 1993 for ranger 2.3 engine"?"


  • 1 - Open the driver-side door of your Ranger. Use a flashlight to locate the fuse panel beneath the dash area on the driver side of the truck, just inside the door. The fuse panel door will be labeled "FUSES" or something similar.
  • 2 - Grasp the handle of the fuse panel cover and pull it straight off the panel. Set the cover aside in a safe place.
  • 3 - Remove the rubber-tipped fuse puller from the panel. The fuse puller looks a little bit like a pair of tweezers with rubber tips.
  • 4 - Grasp the top of the fuse you want to change with the fuse puller. Pull the fuse straight out of the panel. Discard the old fuse.
  • 5 - Press the new fuse into place. If the empty slot is difficult to get to, use the fuse puller to help you get it into place. Press it in until it stops, so it is properly seated in the fuse panel.
  • Sep 03, 2014 | Cars & Trucks

    1 Answer

    2010 ford ranger


    Ground wire or connection probably requires renewal.

    Feb 27, 2014 | Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    15 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5501 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...