Question about Cars & Trucks

Open Question

I have a 2011 4wd avalanche i need the transmission oil pan torque spec as i am changing the filter and fluid. thanks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

  • 43 Answers

SOURCE: Transmission fluid/filter change in 2000 Honda Odyssey

I would not recommend using Dexron III. Honda Odysseys are prone to transmission problems. A drain and fill with Genuine Honda Fluid is Recommended. The drain plug can be removed with a 3/8 ratchet at the bottom of the trans. The fill hole is at the top of the trans. You remove it with a socket on a long extension. The capacity is close to 3 quarts

Posted on Apr 07, 2009

  • 318 Answers

SOURCE: 98 toyota camry transmission service.

You can drain and fill your trans. It will take 2.5 -3.0 quarts of DEX III trans fluid....goes in the fill tube. Or you can get said transmission flushed which changes all fluid including torque converter.....about 15 quarts. Way more thorough.

Posted on Jul 13, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 pontiac g6 transmission filter replacement


Remove the transmission pan - some don't have drain plugs, have a big pan underneath to catch the fluid. Pull filter and install filter on. Clean any debris from pan. Install gasket onto pan and install pan back onto transmission. Torque bolts to factory specs. Fill with approved ATF.

Hope this is helpful :-)

-Scott
25449121-csuuapdgb0syz0ddt50mju2i-5-0.jpg
Pontiac G6 GT Trans Fluid and Filter Change time lapse GoPro

Feb 19, 2015 | 2007 Pontiac G6 GTP

2 Answers

Transmission oil pan bolts tourque specification please


Depends on the gasket used, but 7 to 14 foot pounds. I just snug them up with a ratchet one hand.

Feb 18, 2015 | 2002 Toyota Sienna

1 Answer

Change transmission fluid and filter 1998 mercury mystique


You will need to buy a "TRANSMISSION FILTER KIT," which will include a new transmission filter, uptake gasket, and pan gasket for your transmission. (They run about $20 or less on eBay.) Once you have done that, you will need to hoist the vehicle, and CAREFULLY remove the transmission pan by loosening one bolt a little at a time without removing them, and breaking the old gasket free (hopefully without making too much of a mess of transmission fluid). About half of the transmission fluid (about a gallon and a half) will be in the pan (the rest in the torque converter). It is usually sufficient to replace just the amount of oil in the pan (otherwise you need to remove the torque converter inspection plug on the bell housing and crank the engine to expel the seal, draining the other half of the fluid, then replace the bell housing seal).
Once you have drained away the transmission fluid in the pan, CLEAN THE PAN THOROUGHLY WITH A SHOP TOWEL, and carefully remove the bolts that secure the filter to the transmission valve body. (As I recall it is four 10mm bolts... but not sure on your year model).
Remove the filter, and remove any remnants of gasket on the uptake chamber between the filter and the valve body. MAKE SURE YOU REPLACE THE SMALL GASKET AT THE TOP OF THE FILTER WITH A NEW ONE, OTHERWISE THE TRANSMISSION WILL SLIP DURING THE 1-2 SHIFT DUE TO AIR BEING SUCKED-IN (been there).
Check for correct torque specifications for the filter mounting bolts before tightening them and DO NOT OVER-TIGHTEN THE RETAINING BOLTS.
Once you have replaced the filter, and your pan is clean, scrape away all remnants of gasket material from the mounting surfaces, and position the new filter. (This is easier if you use a tiny amount of silicone RTV to hold the gasket in place and keep it aligned with the pan mounting holes).
Replace the pan, tighten the bolts to spec, re-fill the transmission with the appropriate amount of NEW ATF, then test.

Jul 19, 2014 | Cars & Trucks

1 Answer

Change the transmission fluid in a 2000 ford windstar van


The transmission service is performed by lifting the vehicle in order to get access to the transmission pan. Remove all the bolts that hold the pan in place and the fluid will come out when the pan is being lowerd. From there the filter is accesible and should be changed by simply pulling it downward. The new one is installed by pushing it firmly in place where the old one once was. Clean the pan of the transmission completely including the magnet. place new gasket around the pan and reinstall all the pan bolts. be carefull not to over tighten the pan bolts as it can damage the new gasket the you have put on. next, lower the vehicle and add fluid through the dipstick tube located in the engine compartment. It's best to add 4 quarts then start the vehicle and check the level. If more is needed, add accordingly.
Macs Transmissions
281-394-4951
Macstransmissions@gmail.com
There is none. To change the fluid you need to remove the cover - undo one end first to limit the mess - but yes, it's messy. AnswerBest To Have A Good Transmission Shop Do This. Sometimes You Can Miss Alighn The Filter On Some Tranmissions And They Will Go Out. About Changing The Fluid, Even If You Could It Wouldn`t Do The Job Without a New Filter. Good Luck AnswerThere is an excellent write-up on this procedure relating to a Taurus - the steps are the same.
See "Related Questions" below for more

NOTE: dropping the pan alone will NOT change ALL the fluids - specifically the fluid that is in the torque converter. That would require a shop to perform a full fluid change with their specialized equipment. Answerdrop the pan, replace filter, clean pan replace gasket torq bolts to spec. refill to warm line on stick
Rick
ASE L-1 Master TransMichigan.com AnswerRemove the pan and then remove the filter on the valve body. Clean the pan and gasket surfaces on pan & trany. Install new filter and pan gasket and gently tighten bolts. Caution, if overtightened it will leak!!! Remember how tight they were when you removed them or get a spec & torque them. Refill the trany through the filler tube, DON'T overfill it or it may not shift properly. To check the fluid level the vehicle needs to be running in park and on a level surface. If you do the above you will only change aprox 40% of the fluid. The torque converter, cooler & lines hold the rest and the fluid won't drain out of them.
I suggest you take it to a shop that has a trany FLUSHING machine and will exchange 100% of the fluid and do the filter & gasket at the same time. Add a bottle of seal conditioner when done. With the price of a new trany this should be done every 80,000 kilometers (50-60,000 miles) or check your owners manual for service intervals. Not a lot of shops have this machine so be selective. Might cost up to $200-250.00 for this service to get it done properly but a proper trany rebuild can be $1500-3000.00 or more in some cases on some vehicles.
Flushing the fluid?

But the system should be flushed. Just dropping the pan and draining the oil and changing the filter on your transmission leaves all the used fluid still in torque converter. Have the system evacuated and totally replacing ALL the fluid is a much better approach. It will cost you more but if you plan on keeping the Ford, it's a worthwhile investment.


Source.

Dec 12, 2012 | Cars & Trucks

1 Answer

Where is transmission filter located in 2001 mitsubishi diamante located and how do i change it?


transmission filter in the bottom of transmission bolted to valve body.you need a large drain pan.place drain plug under transmission oil pan.remove transmission oil pan drain plug.let all transmission fluid drain out then screw back drain plug in oil pan.then you need to remove transmission oil pan then remove filter and replace pan gasket also.make sure you have right amount transmission fluid on hand.buy extra because if you short of fluid you cant drive car if fluid level too low.make sure you get the right amount fluid.torque pan bolts to 96 inch pounds.

Nov 10, 2011 | 2001 Mitsubishi Diamante

2 Answers

Just wanted to know how to change transmission oil.


Hello,

Before You change the transmission oil, You need to check if it is due for changing. To check the transmission oil. please follow the steps below:
  1. Open the hood and locate the transmission dipstick. It is in front of the engine on the left side, just behind the radiator cap.
  2. Pull the ring on top of the dipstick to remove it from its tube. Wipe it off with the paper towel and replace it. This will ensure an accurate reading.
  3. Remove the dipstick again an look at the markings at the tip. If the fluid on the stick is below the full line, add more transmission fluid.
  4. Repeat this procedure until the fluid reaches the correct level on the dipstick.

There are different types of engine therefore there are several ways to change their transmission fluid. Unless you got something in there via dipstick its really not necessary to ever change the ATF. It's a messy job because there's no drain plug to change the fluid, but You can do it yourself if you're so inclined. To change the fluid,

  1. You have to get under your vehicle and remove the pan from the bottom of the transmission.
  2. When you loosen the pan, fluid will start to dribble out in all directions so you need a fairly large catch pan. You should also know that removing the pan doesn't drain all of the old fluid out of the transmission. Approximately a third of the old fluid will still be in the torque converter. There's no drain plug on the converter so you're really only doing a partial fluid change. Even so, a partial fluid change is better than no fluid change at all.
  3. A typical fluid change will require anywhere from 3 to 6 quarts of ATF depending on the application, a new filter and a pan gasket (or RTV sealer) for the transmission pan. The pan must be thoroughly cleaned prior to reinstallation. This includes wiping all fluid residue from the inside of the pan and scraping all traces of the old gasket from the pan's sealing surface. Don't forget to clean the mounting flange on the transmission, too.
  4. When the new filter is installed, be sure it is mounted in the exact same position as the original and that any O-rings or other gaskets have been properly positioned prior to tightening the bolts. Then tighten the bolts to the manufacturer's recommended specs.
  5. When refilling the transmission with fresh fluid, be careful not to allow any dirt or debris to enter the dipstick tube. Using a long-neck funnel with a built-in screen is recommended.
  6. Do not overfill the transmission. Too much fluid can cause the fluid to foam, which in turn can lead to erratic shifting, oil starvation and transmission damage. Too much fluid may also force ATF to leak past the transmission seals.
  7. Add half a quart at a time until the dipstick shows full. The transmission really isn't full yet because the dipstick should be checked when the fluid is hot, and the engine is idling with the gear selector in Park. So start the engine, drive the vehicle around the block, then recheck the fluid level while the engine is idling and add fluid as needed until the dipstick reads full.
Hope this helped. Thank You for using FixYa!!!

Jan 27, 2011 | Lexus IS Cars & Trucks

1 Answer

Won.t shift into grear, how do i replace the tansmission filter?


TO DO A TRANSMISSION FLUID CHANGE YOU NEED HAVE TRANSMISSION FLUID ON HAND YOU NEED TRANSMISSION FILTER AND GASKET.YOU NEED 3/8 WRENCH THE RATCHET TYPE WITH METRIC SOCKETS. YOU NEED JACK TO RAISE VECHICLE SUPPORT VECHICLE ON JACK STANDS.YOU NEED A DRAIN PAN. ONCE YOU GET VECHICLE OFF GROUND.PLACE DRAIN PAN UNDER TRANSMISSION OIL PAN REMOVE OIL PAN DRAIN BOLT.LET FLUID DRAIN OUT IN DRAIN PAN THEN SCREW DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.REMOVE OIL PAN AND GASKET. BESURE TO HAVE PAPER TOWEL ON HAND.MAKE SURE TRANSMISSION OIL PAN GASKET SURFACE CLEAN BEFORE INSTALLING NEW PAN GASKET. ONCE TRANSMISSION OIL PAN REMOVED. REMOVE THE OLD TRANSMISSION FILTER INSTALL THE NEW FILTER.THEN WITH NEW GASKET ON OIL PAN IN PLACE.OIL PAN NEED TO BE CLEAN SO THE GASKET ADHESIVE WILL HOLD PAN GASKET IN PLACE WHILE INSTALLING PAN AND GASKET TO TRANSMISSION.INSTALL OIL PAN BOLTS INSTALL THEM CRISS CROSS TORQUE PAN BOLTS TO 7 TO 10 FT LBS. LOOK IN OWNERS MANUAL FOR TRANSMISSION FLUID CAPACITY.BUY 10 QUARTS .TO BE ON SAFE SIDE SO YOU WILL HAVE ENOUGH FLUID ON HAND. IF YOU DONT HAVE NO TRANSMISSION FLUID CAPACITY. ADD 7.5 QUARTS FLUID.WAIT FOR 2 MINUTES.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK. SHOULD BE ON THE FULL MARK.CRANK VECHICLE UP.LET IDLE FEW MINUTES CHECK TRANSMISSION DIP FLUID LEVEL IF DROPPED ADD LITTLE MORE.WHILE ENGINE IDLING GETTING WARM UP. KEEP EYE ON FLUID LEVEL.WHEN FLUID LEVEL STOP DROPPING. APPLY BRAKES HOLD FOOT ON BRAKES SHIFT THROUGH ALL GEARS TWO TIMES. THEN CHECK FLUID LEVEL SHOULD BE ON FULL MARK.CHECK FOR LEAKS WHILE ENGINE RUNNING.

Nov 19, 2010 | 1996 Ford F250 Crew Cab

2 Answers

When changing the trans fluid on my 2004 Avalanche, I understand that you have to disconnect the trans lines from the radiator and run the engine until the fluid stops flowing. Is this correct? If so, do...


I didn't read about running the engine at all during the transmission fluid change. --- Removal & Installation 4L60E/4L65E To Remove:
  1. Raise and safely support the vehicle.
  2. Place a drain pan under the transmission.
  3. If equipped with a drain plug, drain the transmission fluid.
  4. If necessary, remove the bolts and position aside the range selector cable bracket for clearance while lowering the pan. It is not necessary to remove the cable from the lever or bracket.
  5. Remove the catalytic converter.
  6. Remove the oil pan bolts from the front and sides of the pan only.
  7. Loosen the rear oil pan mounting bolts about 4 turns.
  8. Lightly tap the oil pan with a rubber mallet in order to loosen the pan and allow the fluid to drain.
  9. Remove the remaining oil pan bolts.
  10. Remove the oil pan and the gasket.
  11. Remove the filter by twisting and pulling on it.
  12. Remove and discard the filter seal. The filter seal may be stuck in the pump; if necessary, carefully use pliers or another suitable tool to remove the seal.
  13. Clean the transmission and the oil pan sealing surfaces with solvent, and air dry. You must remove all traces of the old gasket material.
To Install:
  1. Coat the new filter seal with transmission fluid.
  2. Install the new filter seal into the transmission case. Tap the seal into place using a suitable size socket.
  3. Install the new filter.
  4. Install the oil pan and new gasket. Tighten the bolts alternately and evenly to 97 lb in (11 Nm).
  5. Install the catalytic converter.
  6. If previously removed, install the range selector cable bracket and bolts. Tighten the bolts to 18 lb ft (25 Nm).
  7. Apply a small amount of sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the oil pan drain plug, if equipped.
  8. Install the oil pan drain plug, if equipped. Tighten the plug to 13 lb ft (18 Nm).
  9. Lower the vehicle.
  10. Fill the transmission to the proper level with DEXRON® III transmission fluid.
  11. Check the COLD fluid level reading for initial fill only.
  12. Inspect the oil pan gasket for leaks.
4L80E/4L85E To Remove:
  1. Raise and suitably support the vehicle.
  2. Place a drain pan under the transmission oil pan. Drain the transmission fluid and install the plug. Tighten the drain plug to 13 lb ft (18 Nm).
  3. Support the transmission with a transmission jack.
  4. Remove the transmission crossmember.
  5. Disconnect the range selector cable end from the transmission range selector lever ball stud. NOTE: It is not necessary to remove the selector cable from the bracket.
  6. Remove the transmission range selector cable bracket. Reposition the bracket and cable.
  7. Remove the oil pan bolts. NOTE: The transmission oil pan gasket is reusable. Replace as needed.
  8. Remove the oil pan and gasket.
  9. Remove the magnet from the bottom of the pan, if necessary.
  10. Remove the oil filter and neck seal.
To Install:
  1. Clean the transmission and the oil pan sealing surfaces with solvent.
  2. Install the filter neck seal and filter.
  3. Install the oil pan gasket to the pan.
  4. Install the magnet into the bottom of the pan, if necessary.
  5. Install the oil pan and bolts. Tighten the oil pan bolts to 18 lb ft (24 Nm).
  6. Install the transmission range selector cable bracket. Tighten the bolts to 18 lb ft (25 Nm).
  7. Connect the range selector cable end to the transmission range selector lever ball stud.
  8. Install the transmission crossmember. Tighten the fasteners to 70 lb ft (95 Nm).
  9. Install the transmission mount nuts. Tighten the nuts to 30 lb ft (40 Nm).
  10. Remove the transmission jack.
  11. Lower the vehicle.
  12. Fill the transmission to the proper level with DEXRON® III transmission fluid.
prev.gif next.gif

Aug 26, 2010 | 2004 Chevrolet Avalanche

1 Answer

2002 Chevy Malibu Transmission Filter Change...


Not very hard by all means if you have a few basic hand tools, a torque wrench and ramps or a jack and stand to lift the car up...

About 95% of automotive automatic transmissions do not have a drain plug, so you have to remove the transmission pan to drain the fluid, and the filter is up under the pan anyway. Remove all the pan bolts, drop the pan, make sure you have a container ready for the oil under it... If you buy the filter/pan gasket kit and you look at the filter it should be a pinch to spot. 649425d.jpg This is what your particular filter looks like (from the top)

Replace the filter, clean the pan/transmission mating surface with emery cloth, scuff pad, or whatever needs to be used to get the metal clean again (without removing too much material eg. a grinder would definitely cause a leak).

Reinstall the pan with the new gasket (do not use silicone or any type of fluid "gasket maker" Automatic transmissions have a lot of tiny oil passages which can easily be blocked by these products and cause severe transmission damage)

Torque the bolts to the manufacturer's spec (you don't really need a torque pattern, just start from the middle of the pan and alternate from side to side (this is to make sure the pan seats square with the transmission body)) 90% of the time you could tighten them anyway you want and wouldn't have a leak but you want it done right the first time so don't take any chances (you should be able to get the torque value from the parts store where you get the filter/gasket kit). I'm not able to pull out an exact spec for you right now.

Fill the tranny up, then drive th

Sep 09, 2008 | 2002 Chevrolet Malibu

1 Answer

Transmission fluid change


More than likely, like most automatic transmissions, yours does not have an oil plug. You need to drop the transmission oil pan to drain the old oil... You need to buy a transmission filter/pan gasket kit. The filter is located on the bottom of the tranny. You will see it when you remove the pan. Replace the filter, thoroughly remove any traces of old gasket material, clean the mating surfaces, and reinstall the pan with the new gasket. Torque the pan bolts to the manufacturers spec (you should be able to get this where you buy the filter/gasket kit). Refill the transmission through the dipstick (Capacity for the Voyager is 4 quarts, make sure to use ATF Plus (Type 7176) for your particular tranny, NOT Dexron, Mercon, or generic automatic transmission fluid, Chrysler transmissions do not like any other kind and tend to fail quite quickly with the wrong fluid). Fill to the full cold level. Start the engine, move the shifter through all gear ranges, and put it back in park. Leave the engine running and refill to cold full. Drive the car for 5-10 minutes and, with the engine still running and the car in park, fill to Hot full. You should be ready to go!

Aug 26, 2008 | 1997 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...