Question about Chevrolet Classic

1 Answer

I need to know how much pounds is apliied to a 350 chevy cylinder heads

Posted by on

Ad

1 Answer

What is the year and model of your vehicle?

On a 1968 Chevy 350 small block it is 60-70 ft/lbs with sealant applied

When torqueing the heads, it is helpful to start at around 25 ft. lbs. and torque all the bolts, then go to 50 ft. lbs., and finally, your specified torque. Doing this in increments will help give a nice even torque to the heads

Posted on Jul 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing the head on chevy cavalier 2.2 need to know what to torque head bolts


On the first pass, torque the long bolts to 46 foot pounds, short bolts to 43 foot pounds. On the final pass, turn all bolts and additional 1/4 turn.

Mar 23, 2011 | 1998 Chevrolet Cavalier

1 Answer

What are the torque specs on edelbrock aluminum rpm heads on chevy 350


I would think that they are the same as a regular 350 and that is 65 foot pounds.

Nov 05, 2010 | 1983 Chevrolet Malibu

1 Answer

I need to know the sequence to tighten cylinder head bolts on a 97 dodge intrepid 3.5 6 cylinder


First, torque them all to 45 ft pounds(61 nm), second to 65 ft pounds (88nm) go over them a third time @65 ft pounds again. then 1/4 turn and you are done.

Sep 14, 2010 | 1997 Dodge Intrepid

2 Answers

How do i ajust my lifters on a chevy 350 tbi


they are hydralic and are not adjustable during normal maintenence
if you removed heads then you need to adjust them
if they are clicking then a lifter may be bad or the cam shaft is going flat

Mar 22, 2010 | 1992 Chevrolet K1500

1 Answer

94 mazda B3000 3.0L cylinder head torque specs


Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Sep 17, 2009 | 1994 Mazda 2WD B Series Pickup

1 Answer

Head bolt torque


They have this listed under a 2007 E-350 but I new it couldn't be. Any how the torque specs are as follows. The big bolts 1-26 are to be torqued first they are torqued to 120 ft. lbs. then rechecked to 120 ft. lbs. Then tightened 1/4 turn or 90 degrees. After that that loosen all the bolts up till the washers are loose again then perform the exact sequence all over again. After that tighten the small bolts on the outside part of the cylinder head all 7 of them to 20 ft. lbs. Good luck.

Apr 11, 2009 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

4 Answers

Chevy 5.7 17 bolt heads tork specs


Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb

Oct 13, 2008 | 1999 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...