Question about Cars & Trucks

Open Question

The key fob on my 2006 Jeep Liberty Sport CRD does not lock or unlock any of the four doors but it does lock/unlock the tailgate. Signal lights flash when the fob button is pushed. Any ideas for fix?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: tailgate stuck

The auto lock burned out you need to go to dealer and get ripped off for $300 to have them fix it. Make sure you tell them the exact problem since it took 3 mechanics two days to figure mine out after i told them what was wrong the first time. Not too swift there.

Posted on Aug 15, 2008

  • 12 Answers

SOURCE: 2006 gmc yukon back door/hatch won't unlock

Check battery voltage. if above 13.7 volts move to rear lock actuator and measure battery voltage at actuator if above 13.6
replace actuator if below specs. check grounds and alternator out put as follows, alternator output 13.7 to 14.25 volts. key off battery volts should be 12.90 + - 3/10 of a volt and about the same voltage at the actuator. let me know. kindest regards Bill

Posted on Jan 30, 2009

  • 30 Answers

SOURCE: 2002 Ford Focus Doors lock with key fob, but horn does not honk

there are two seperate horns

Posted on Mar 11, 2009

keemo68
  • 1263 Answers

SOURCE: Power door locks won't unlock + tailgate won't open

your issue involves the master control switch panel on the drivers side and or the passenger side as well some how the contact inside the switch assembly has either shorted out or no longer makes contact for the unlock side of the circuit. replace the drivers side panel switchs it's either a series of switc hs or mostimes one sigle board of switchs. you are better off going to an auto parts store rather than a GM dealership this will save you quite a bit on cash on the parts. now as to the rear tailgate. if it is electronic controled and there is an issue with the master switch you can,t manually unlock it because of a safty issue built in the system. you can manually unlock the passenger compartment doors for thew same reasons of safety but doesn't apply to the tailgate. just replace the parts and this will take care of the problem

Posted on Apr 18, 2009

VOLVOCHICAGO
  • 33 Answers

SOURCE: 1999 Volvo V70 - The tailgate door will not unlock

you will need new t gate lock assembly parts inside are worn out

Posted on Aug 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello,same as Matt,first my horn didn't work,is it unplugged,then I plug the horn,does not function .unlocks remotely and then the alarm begins to function!unplug quickly..I am French.THANK YOU


posting to USA Forum with a French car.
ok, its a CRD diesel, common rail diesel. we have no books on it here, nor car. my guess near same car as our Liberty
does car drive ok? engine run ok, and all things on car work ok but your listed items?
So the alarm is failing.
So the doors unlock ok, with the key fob, but then the alarm goes off. Id say, it needs help. get car serviced, or at least scanned.
if both key fobs fail, (do you have both, if no OOPS) get it serviced.
so does engine start and run, after unplugging horn.
does it?
if not does it crank over,(start spin over engine>?"
if no , then battery is dead.

Jul 30, 2016 | 2006 Jeep Grand Cherokee

3 Answers

How do i reset anti theft on 06jeep liberty. It wont let the gas. Go inyo the intake


Is there a theft light flashing? If so,use the key fob to lock and unlock the doors. This usually resets the system

Apr 27, 2015 | 2006 Jeep Liberty

1 Answer

The tailgate lock and rear wiper will not work on my 2006 jeep liberty I also noticed it will not unlock at all with the key until im close to the driver door maybe related im not sure


Without buying the factory service & diagnostic manuals
or cd---- your Not going to find anything

So you need a dealer or local shop-- that has the data & info
to find a problem

Dec 01, 2014 | 2006 Jeep Liberty

1 Answer

Jeep liberty 2006 power lock will lock but not unlock


there are 3 ways to lock.
key metal
on door switches
and the FOB, RKE.

so is this a fob question? key fob? only failure???????
did you know that many fob modes are PROgrammable?
the operators guide tells you how to do that.
did you try both fobs, that came with car new., if not why not?
did you replace the 8 year old fob batteries, no , why not now.?

on my 08 (for example) :
can program it to only open drivers door. or all.
and autolock feature off or on.

on my other car all was worked fine. then drives door failed
to open (all 3 fobs fail, one is new) the door solenoid was bad.
$100 part. now fixed, by me.
so do all fobs fail. if in fact this is a FOB question
RKE (called remote key entry by jeep)

i have 4 fobs for my jeep now. you must have 2 good keys.
to make a 3rd by self.
so keep 2 , never ever used. to be self sufficient.
this is not a door issue, above 3 lines, its a not getting stranded issue.


Mar 31, 2014 | 2006 Jeep Liberty

1 Answer

2009 jeep liberty only drivers door unlocks


you just get this car.
or it worked before but not now? key questions.

door switch driver and RKE not working right.

and some cars the driver has a master switch and local switch.
and some have a kids safe switch that kills the other doors.
i dont have the opr,guides. for liberties.

in this case , this is a programmable feature. most newer jeeps.
you can program most cars. for (only driver door works with fob)
this is for security, (like airport parking , alone, at night)
the operators guide (lost already )covers this. in the glove box.
most folks don't read it ,they just drive to jeep service and
ask to have it set like you want. and pay $100.
it could be a fault too... but that will take checking above first.
on my other car, i must click 2 times to open all doors, (GM)

the dealer will scan the PCM/BCM puters. to see if they are throwing
DTC errors. any good scan tool can do this.
and check fuses first. never last. or get egg in face.

did you read this?
http://justgivemethedamnmanual.com/jeep/jeep-liberty-owners-manuals/

lost it , then get it and put it on a flash stick and put it back in the glove box or burn a CD . (or kill a tree and print it)

page 21
To Unlock the Doors and Liftgate
Press and release the UNLOCK button on the RKE
transmitter once to unlock the driver's door or twice to
unlock all doors and the liftgate. The turn signal lights
will flash to acknowledge the unlock signal. The illuminated
entry system will also turn on.

Remote Key Unlock, Driver Door/All Doors First
This feature lets you program the system to unlock either
the driver's door or all doors and the liftgate on the first
press of the UNLOCK button on the RKE transmitter.
To
change the current setting, proceed as follows:
• For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to "Remote Key
Unlock," under "Personal Settings (Customer-
Programmable Features)," under "Electronic Vehicle
Information Center (EVIC)" in Section 4.

end quote.

my GUESS, you didnt RTM.
read it.

Mar 21, 2014 | 2009 Jeep Liberty

1 Answer

How do i reset central locking on a micra 04 reg


Try the following:

"KEY FOB PROGRAMMING
NISSAN
SYSTEM DESCRIPTION
The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and hazard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.
A maximum of four remote controls are allowed to be programmed.
ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II
Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.
Procedure
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds."

Mar 12, 2012 | Nissan Cars & Trucks

2 Answers

2006 Jeep liberty sport remove door panel driver side


2005 jeep liberty,the key will not unlock the driver side door and the power lock will not unlock the driver sider door.

May 11, 2010 | 2006 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...