Question about Ford Fusion

Open Question

My driver door would not lock. is working now but realized the anti theft system is not little on my dash. Is there a fuse for the anti theft system. I have a 2002 for fusion.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1994 cadillace anti theft system

I just had this same problem with a '96 . do you have a vats key in your '94? you need to bypass the VATS system. read some of the blogs on this site and it will tell you how to do it. I fixed mine with a $2 resistor from radio shack.

Posted on Oct 12, 2008

Ad
scramblepad
  • 66 Answers

SOURCE: Anti-theft system stuck triggered

Doing roadside assistance I have ran into this problem several times and if you look in your owners manual it will tell you how to reset it. Some of the cars you have to wait up to 10 min. with the key in the ignition and try again. The light will go out. READ carefully our owners manual.
Hope this helped....Kevin

Posted on Jan 31, 2009

  • 1 Answer

SOURCE: 1997 ES 300 How to reset anti-theft system when car won't start

With the doors shut, insert the key into the drivers door lock. Lock and unlock the door 5 times. This should reset the system. If that doesn't work you should contact a qualified repair shop.

Posted on Mar 20, 2009

nckracing
  • 4 Answers

SOURCE: my anti-theft system has lock my focus engine how

if the theft light is flashing fast, the PATS(passive anti-theft system) can only be reset with a ford scanner... you can try leaving the key in the on position for a little over an hour, sometimes it works.

Posted on Jun 22, 2009

  • 30 Answers

SOURCE: how do you reset the anti theft system

Try disconnecting your battery cables then wait about 10 minutes. The computer should reset itself. Reconnect the wires to the battery. It is normal for the theft light to blink about every 5 seconds when the ignition key is out or in the off position. This means the system is armed and working properly. Hope this helps. God bless!

Posted on Oct 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002. Why has anti lock cut off ignition and fuel?


Anti THEFT cuts off fuel pump and the ignition module. That is what it is for. The theft light on the dash should be on too. Something tripped the anti-theft system Try resetting the anti-theft module by locking and unlocking the drivers door with the key.

Jan 01, 2016 | Ford Cars & Trucks

1 Answer

Reset anti theft system


the remote starter "brain " should be a black box under dash on driver side will have wires with plugs going to it usually will have at least 1 6wire plug that if followed there path they will lead to key ignition switch. if you find this box unplug it untill you can get remote starter repaired.

Oct 30, 2013 | Chevrolet Cobalt Cars & Trucks

1 Answer

No indicators working found fuse box which fuse?


When you are talking about "indicators" we could assuming that your are refer about signal lights. This work with "flashers" devices.

For 1996 Audi A4 2.8L SFI 6cyl the Flasher is located in front seating area, driver side, under dash, behind dash lower panel, mounted above driver side of steering column.

About generic fuses, open the driver side door. Remove panel on left side of dash. Fuse box is behind panel:

Fuse # / Description / Amps
1 / Heated washer jets / 5
2 / Turn signals flasher unit / 10
3 / Headlight washer, illumination of glove compartment, engine compartment, climate control, automatic transmission, instrument cluster / 5
4 / License plate light / 5
5 / Instrument cluster, seat heating, test connection for cruise control, bulb monitor for auto-check control, Automatic transmission display, switch lighting, mirror switches and actuators, airbag warning light, outside temperature indicator, Climate control / 10
6 / Central locking system / 5
7 / Anti-lock brake system / 10
8 / Vacant
9 / Mirror heating / 10
10 / Vacant
11 / Cruise control (automatic transmission) / 5
12 / On board diagnostic system / 10
13 / Brake lights / 10
14 / Interior lights, reading lights, anti-theft alarm system, vanity mirror / 10
15 / Instrument cluster, power windows, climate control, automatic transmission / 10
16 / Anti-lock brake system, Anti-Slip-Regulation / 5
17 / Heated door locks / 10
18 / High beam right / 10
19 / High beam left / 10
20 / Low beam right / 15
21 / Low beam left / 15
22 / Tail and side marker right / 5
23 / Tail and side marker left / 5
24 / Wiper and washer system / 25
25 / Blower for heating, climate control / 30
26 / Rear window defogger, mirror heating / 30
27 / Rear window wiper / 15
28 / Fuel pump / 15
29 / Engine timing / 20
30 / Sun roof / 20
31 / Tail lights, cruise control, automatic transmission / 15
32 / Engine timing / 20
33 / Cigarette lighter / 15
34 / Engine timing / 15
35 / Trailer receptacle / 30
36 / Fog lights / 15
37 / Radio / 20
38 / Luggage compartment light, central locking system / 15
39 / Emergency flasher / 15
40 / Horn / 25
41 / Anti-lock brake system / 25
42 / Vacant
43 / Vacant
44 / Seat heating / 30

Hope this helps (remember to rate and comme this free answeer).



Jun 16, 2011 | 1996 Audi A4

1 Answer

The remote to my 2002 cadillac deville dont unlock or lock my doors or open my trunk like it used to. my power locks dont work. i got in the car last week and on car display says theft attempt, the lights...


Either via an actual theft attempt or you (or someone with your keys) not realizing that you/they actually armed the vehicle and opened the door or trunk afterwards.

Essentially this sounds like the vehicle was entered after being armed and the proper precedures not met to reset it.

The car may just need to be locked from the outside with the key (not the remote or keyless entry) while the doors are closed and windows are up, and then also unlocked with the key...

However it sounds as though you have perhaps driven it since then. If this is the case

You may want to check all your fuses and replace the ones affected by the anti theft system.
Security - Pwr Locks - Horn - Pwr Trunk Release _ Int Lights - and maybe The Emergency Flasher as well.

Be sure and check under the Dash, Hood and under the Back seat.

Cadillac recommends after a theft attempt, the vehicle may need to be serviced. So I recommend going through the fuses first, even replacing the battery in your remote fob and then if the problems still persist. have the vehicle serviced.

Good Luck and Happy Motoring

Respectfully

Jun 12, 2011 | Cadillac DeVille Cars & Trucks

2 Answers

I work for a garage and we have a 1998 mystique that wont start we were wondering if there was some sort of anti-theft systeme that we dont know about and also we would like to have the were abouts of the...


Starting System
The function of the starting system is to crank the engine at a speed fast enough to allow the engine to start. Heavy cables, connectors and switches are used in the system because of the large currents required.
The starting system consists of a gear reduced starter motor, battery, remote control switch (ignition switch) and relay.
Vehicles equipped with automatic transaxle have a transmission range sensor attached to the circuit which prevents operation of the starter motor unless NEUTRAL or PARK are selected.
Vehicles equipped with a manual transaxle have a start inhibit switch in the starter control circuit, which prevents operation of the starter motor unless the clutch pedal is in the applied position.
------------------------------------------------------------------------------
The anti - theft protection system provides protection from unauthorized entry into the passenger compartment.
The system is controlled by an anti - theft alarm control. When armed, unauthorized entry into the vehicle is detected by lamp switches.
Once triggered, the system flashes the headlamps, the parking lamps, the alarm indicator, and sounds the horn. In addition, the starter circuit is disabled to prevent starting the vehicle until the system is disarmed.
System Arming
The system will be armed by the remote entry transmitter when the following input sequence is followed:
  1. Turn the ignition switch off and remove the key.
  1. Close all doors (unlocked).
  1. Press the LOCK button on a transmitter to lock doors. Alarm warning lamp will turn on.
  1. Wait for the anti - theft warning lamp to turn off.
The system will also be armed when the following input sequence is followed:
  1. Turn the ignition switch off and remove the key.
  1. Open a door. Alarm warning lamp will flash.
  1. Lock doors with power door switches. Alarm warning lamp will now glow steadily.
  1. Close all doors.
  1. Wait for the anti - theft warning lamp to turn off.
Opening any door will activate the alarm after the alarm is armed.
Disarming an Untriggered System
The system can be disarmed by performing one of the following procedures.
  • Driver or RH front door is unlocked with a key.
  • Driver door is unlocked by pressing the UNLOCK button of a remote entry transmitter.
  • If remaining in the vehicle, turn the ignition switch to ON or ACC position.
System Triggering
The armed alarm system will be triggered if any door is opened without using a key or a remote entry transmitter to unlock the door first.
Disarming a Triggered System
Carry out either of the following steps will disarm the triggered alarm system.
  • Driver or RH front door is unlocked with a key.
  • Driver door is unlocked by pressing the UNLOCK button of a remote entry transmitter.
Two minutes and 45 seconds after the system has been triggered, the horns and exterior lamps will shut off automatically. The system will then reset to an armed state and will trigger again if another intrusion occurs.
--------------------------------------------------------------------
Passive Anti-Theft System (PATS)
The Passive Anti-Theft System (PATS), known as SecuriLock, is fully passive in operation and requires no special procedures by the driver to arm or disarm the system. It is invisible to normal scrutiny and is operated by a transponder within the key body. This communicates with the module through a transceiver mounted around the ignition switch lock barrel.
The PATS functionality is incorporated within the powertrain control module.
PATS keys contain an electronic device inside, and are physically larger than a non-PATS key.
The transponder code reading is carried out when the key is inserted into the ignition lock barrel, and turned from position 0' to position II' or III' to crank the engine. If the PCM receives the correct code signal, the engine will start. Should the code received not be recognized, the engine will not crank as the PATS is still armed and the engine immobilized.
Anti-Theft Indicator
Whenever the ignition is switched on the anti-theft indicator will remain on for three seconds while the system carries out an initial ignition key-read.
The anti-theft indicator will flash rapidly for three seconds to indicate the PATS has immobilized the vehicle.
For additional information on the PATS fault codes, refer to the Diagnosis and Testing section.

Aug 12, 2010 | 1998 Mercury Mystique

1 Answer

No. i need to find the fuse for my alarm system. and i don't have a manual


Section 13-11: Anti-Theft System, Active 1998 Villager Workshop Manual DIAGNOSIS AND TESTING Inspection and Verification
  1. Verify customer concern by operating the anti-theft alarm system.
  1. Visually inspect the following components of the anti-theft alarm system:


    VISUAL INSPECTION CHART Mechanical Electrical
    • Door lock key cylinders binding
    • Loose hood anti-theft switch
    • Blown fuse(s):
      • 7.5A S.E.C.
      • 10A ELECTRON (IGN)
      • 30A PWR WDW
      • 15A HORN
    • Damaged circuit breaker #1
    • Damaged or corroded anti-theft relay
    • Broken or loose wiring
    • Damaged,loose or misaligned hood anti-theft switch
    • Damaged or loose luggage compartment lamp switch
    • Damaged or loose door courtesy lamp switch(es)

  1. Verify that the following systems are operating correctly:
    • Horn.
    • Headlamps.
    • Instrument cluster and panel lighting.
    • Power door locks.
    • Keyless entry remote transmitter (if equipped).
    If any systems are not functioning properly, refer to the appropriate section of this service manual for diagnosis and testing before proceeding.
  1. Check wiring harness for obvious signs of looseness, corrosion, or damage.
  1. If the fault is not visually evident, determine the symptom and proceed to the Symptom Chart.

Apr 19, 2009 | 1998 Ford Expedition

1 Answer

We replaced the car's battery and now the dash board lights blink


Under the dash on drivers side is the black box for the security system. If you look on the box there is a little red button. Push the button for a couple of secounds and it will click and stop your marker lights and dash lights from flashing. It is a stock anti theft part of the security system. Hope this helps.

Jan 10, 2009 | 1997 Subaru Legacy

2 Answers

1997 ES 300 How to reset anti-theft system when car won't start


With the doors shut, insert the key into the drivers door lock. Lock and unlock the door 5 times. This should reset the system. If that doesn't work you should contact a qualified repair shop.

Jan 01, 2009 | 1997 Lexus ES 300

1 Answer

1992 chevy corvettecranks but doe's not start.fuel pump not working but good.fuse good doe's not have power to fuse at all.


The built in factory anti-theft system disables the fuel pump if it is triggered, or this can be caused by a fault in the anti-theft, those are a few of the reasons, arm and dis-arm anti-theft is it working properly? Follow this procedure to check security system:

The Security System is reset by unlocking the driver's door twice with the Ignition Key, but if it does not reset, most likely the Ignition Lock Cylinder has failed. It has small contacts which 'sense' the pellet on the key and transmits that data to the Anti-theft Module. Often the contacts, or the micro wires, break causing the module to think you have no key in there. The ASR may be illuminating since the Security System is active, trouble codes?

Aug 04, 2008 | Chevrolet Corvette Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5581 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...