Question about 1997 Chevrolet S-10 Pickup

1 Answer

No fluid pressure coming out of ABS modulator

No fluid pressure coming out of ABS.
I have no fluid pressure coming out of the one port of the ABS modulator that goes to the rear brakes. It comes out the front brakes fine, but i cant get fluid to go to the rear brakes. Anything i can do to fix it instead of replacing the modulator? I don't see any other valves in the system. i got the master cylinder, then lines go from there to the ABS modulator, then lines come out of there and go the the wheel cylinders. thanks for the help keith

it a 1997 chevy s-10 pickup 2 wheel drive 2.2 liter

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

You have to get a scanner and perform a function bleed test on abs valve to work air out of valves, some also have push pins under rubber buttons on side that you can manually push to remove air

Posted on Jul 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of abs pressure switch on 2003 mazda tribute


probly in the abs module-which is in the brake fluid line--a new module can cost 3000--if the fluid is dark changeit cause it destroys the modules--remembr u can stil brake w out antilock

Nov 12, 2014 | 2003 Mazda Tribute

1 Answer

Brake pedal loosing pressure


Honda had two brake reservoirs one on the normal brake master cylinder the other on the ABS module. If abs fuse has no power the module has no power. that power comes from the main fuses in underhood fuse box. the abs system is supplement system to normal braking system loss of brake pedal is a air problem or drum brake adjustment problem or a loose wheel bearing pushing the caliper piston back into caliper requiring more fluid to get brake to work causing a low pedal.

Nov 12, 2013 | 1995 Honda Accord

1 Answer

No pressure on brake pedal 95 suburban 2500 4x4 7.4L


try bleeding your ABS block first, if that doesn not work could need a master or proportioning vavle. Some scan tools are capable of bleeding the ABS system on some vehicles, and some you have to bleed manually.

Apr 07, 2012 | 1995 Chevrolet Suburban

1 Answer

Leaking brake fluid from modulator valve


The brake pressure modulator valve is the heart of the abs and traction control systems. A fault in this part would cause the abs and traction control lights to come on as well as the service stability system. If this valve fails, the wheels could possibly lock up. If you were to experience the wheels locking up, you should pump the brakes to regain control over the vehicle.

Dec 21, 2011 | 1989 Ford Ranger

1 Answer

Looking for a replacement part for My 1999 Ford F150 XL 4.6 L... With no luck. (I had a faulty front brake line - now after replacing it ..it will not bleed air or fluid) Disconnected the line from the...


YOU NEED A SCAN TOOL TO BLEED BRAKES.THE SCAN TOOL REACTIVATE HYDRALIC BRAKE MOTOR.YOU CAN RAISE VECHICLE WHEELS OFF GROUND SUPPORT SECURE SAFELY. ALLOW DRIVE WHEEL SPIN 5 MILES AN HOUR WHILE VECHICLE OFF GROUND THE WHEEL SENSORS WHILE WHEELS SPINNING WILL ACTIVATE ABS HYDRALIC MOTOR TO BUILD UP BRAKE FLUID PRESSURE.THEN LOWER VECHICLE TO GROUND.MAKE SURE MASTER CYLINDER BRAKE FLUID LEVEL CORRECT THEN BLEED BRAKES IF BRAKE DONT FEEL FIRM OR SOLID DONT DRIVE HAVE VECHICLE TOWED IN.GARAGE WILL HAVE TO USE SCANNER TO BLEED BRAKES.

Nov 17, 2010 | Ford F-150 Cars & Trucks

2 Answers

I replaced the brake master cylinder on my 91 Lincoln Mark 7 with a non high pressure master cylinder and the rear brakes do not hold. Do I need to change the cal. on the rear also?


ANTI-LOCK BRAKE SYSTEM (and HCU-Hydraulic Control Unit)
General Information The 4-Wheel Anti-lock Brake System (ABS) is an electronically operated, all wheel brake control system. Major components include the power brake booster, master cylinder, the wheel speed sensors, and the Hydraulic Control Unit (HCU) which contains the control module, a relay, and the pressure control valves. The system is designed to ****** wheel lockup during periods of high wheel slip when braking. Retarding wheel lockup is accomplished by modulating fluid pressure to the wheel brake units. When the control module detects a variation in voltage across the wheel speed sensors, the ABS is activated. The control module opens and closes various valves located inside the HCU. These valves, called dump and isolation valves, modulate the hydraulic pressure to the wheels by applying and venting the pressure to the brake fluid circuits. Some models are equipped with a Traction Assist (TA) system. The TA system senses wheel spin upon acceleration, turns on the Hydraulic Control Unit (HCU) pump and applies fluid pressure to the appropriate rear wheel. Two additional isolation valves in the HCU will also close to permit fluid to flow only to the rear wheels. The TA system monitors TA usage to avoid overheating the rear brakes. If the system does sense brake overheating, the ABS module will inhibit TA operation until the rear brakes are permitted to cool down.
---
SYSTEM COMPONENTS The anti-lock brake system consists of the following components:
  • Vacuum booster and master cylinder assembly
  • Hydraulic Control Unit (HCU)
  • ABS module
  • Wheel sensors
  • Pedal travel switch
---
On 1992-1994 and 1995-00 a scanner is used to perform the brake bleed. But on yours, I think it's different according to the manual.
---
What do you mean change the cal. on the rear also? Do you mean Caliper?

Jul 26, 2010 | 1991 Lincoln Mark VII

1 Answer

When I restart the engine when hot, the ABS and Brake lights come on and stay on. Not when a cold start


It sounds like the ABS accumulator needs to be replaced. If you crack the line open at the ABS module and the fluid comes out with lots of pressure then you have confirmed this suspicion.

Jun 10, 2009 | 2001 Oldsmobile Bravada

2 Answers

1994 Cavalier -replaced master cylinder-no pressure to rear brake


The most common bleeding procedure is to bleed the ABS brake furthest from the master cylinder first, then bleed the other brake that shares the same hydraulic circuit (which may be the other rear brake on a rear-wheel drive car, or the opposite front brake on a front-wheel drive car or minivan). After these have been bled, you then bleed the other brake circuit starting with the furthest brake from the master cylinder.
Air can be very difficult to remove from an ABS modulator assembly because of all the nooks and crannies inside the unit. The modulator may have eight to 10, or more, ABS/traction control solenoid valves, plus various check valves and dead-end ports. Some ABS modulators have special bleed screws to help you vent the trapped air when bleeding the system. Others do not and require the use of a scan tool to cycle the ABS solenoids while you bleed the system. 1. To bleed the isolation valves in the modulator, there are two bleeder screws. Start with the one toward the engine. Turn the ignition on and apply light pressure on the brake pedal. Open the bleeder screw and allow the fluid to flow until clear. Close the screw and do the same at the second bleeder screw. 2. Depressurize the accumulator by pumping the pedal 40 times with the key off. Wait about two minutes for the brake fluid to de-aerate, then refill the fluid reservoir with DOT 3 brake fluid. 3. Now you can bleed the boost section. This is done by applying moderate pressure on the brake pedal and turning the ignition on for three seconds, then off. Repeat this a total of 10 times. Make sure the pedal feels firm when you have finished, and give the car a road test to make sure the brakes are working properly.

Mar 15, 2009 | 1994 Chevrolet Cavalier

1 Answer

Brake fluid is forced out under pressure from ABS resevior


Hi,welcome to fix ya. this usually happens when the solenoids stick in the modulator . take the car to a dirt road and apply the brakes several times to activate the ABS system to clean up the valves in the solenoids. this usually frees them up. if not you will need to replace the ABS modulator.

Feb 18, 2009 | 1990 Honda Accord

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

604 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...