Question about Cars & Trucks

1 Answer

Changed trany oil in demio 1999. The hold light started to blink and car did not change to highest gear. After about 500km one day at a robot stop the car lost drive. What should I do to repair this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 9,771 Answers

Change the filter in the transmission and be sure the oil level is correct.

Posted on May 04, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u clear the code of change oil light on a 1999 grand am


on the drivers side end of the dash there is a removable panel that sometimes says fuses on it. You will need to have the door open to remove it. Once it is off you will see a red reset button. Turn the key on. push the reset button one time, the change oil light should start to blink. if not press it again. Once the change oil light is blinking press and hold the reset button for about 10 seconds. an audible tone will beep three or four times and the light will go out.

Jun 23, 2011 | 1999 Pontiac Grand Am GT

1 Answer

Recently the Maintenance Required light comes on and blinks for a couple of minutes, then goes off. We put new brakes on the front and we changed the oil and I thought the light would stop, but it's still...


the car is telling you that the oil needs to be changed/ the milage has reached the limit for needing to be changed. even if you have changed the oil it will still warn you after 7500 miles to change the oil. To make the light go off, press and hold the knob the resets your milage for 15 secs then turn the key to the on position(dont start the car) then continue to hold the knob in for about 30 secs, release, turn the car off, wait 5 secs, turn car to on position, then back off the start the car it should clear the maintence light.

Oct 18, 2010 | 2005 Honda Pilot

2 Answers

How to reset my oil change light in a 99 firebird 3.8


You do this via the trip odometer. With engine on, push in and turn trip odometer to the left and hold for about 5-7 seconds. The light will start blinking, keep holding until the blinking stops and you should be good to go.

Sep 26, 2009 | 1999 Pontiac Firebird

1 Answer

My jeep went all sluggish and wouldnt leave 1st gear unless i turn off the engine now it wont even start its like its an automatic car it just refuses to change gears and tries to drive of its own accord.


hope its now the transmission gone bad, but try these check, is there trans fluid in the trany/ check the fuse ad relay pertaining to the trany. change the filter

Jul 21, 2009 | 1999 Mitsubishi Montero Sport

3 Answers

Mazda Demio:The HOLD button blinking and gear stack to no.3


i have a mazda mpv 2001 , hold lihgt is blinking , how can i fix it ?

Mar 24, 2009 | Mazda B2600 Cars & Trucks

1 Answer

Automatic gear box


yes it can be checked and if you can get any oil on the dip stick smell it if it smells bernt or bad smelling the trany is prob no good

Feb 02, 2009 | 1999 Volkswagen Passat

2 Answers

Mazda 626 'HOLD' light after gear box oil seal was replaced


I have the same problem with my car I think its the torque converter clutch but you should visit a diagonestic machine just to find out

Dec 06, 2008 | 1998 Mazda 626

2 Answers

Trany would slip at high speed and sometimes if i got on it hard. It was just doing it maybe once every 4/6 months, until one day i was driving to work. I was goig 75 mph and all of a sudden i lost every...


Have the vehicle scanned for diagnostic trouble codes,and repair any codes.More than likely the trans needs a rebuild.If the fluid smelled burnt,then obviously clutches or bands are burnt inside the trans.Changing the fluid just got rid of the smell,whatever is burnt is still hurnt.It is best to stop driving the vehicle,as continuing to drive it will just cause more damage to whatever is damaged.Those transmissions are prone to pump problems too.

Jul 26, 2008 | 2001 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...