Question about Honda Cars & Trucks

Open Question

2003 Honda cry 2.4 auto.while taking off valve cover a small oval,I think brass,washer fell out on the garage floor.Idk were I goes,fell like a dummy,if anyone can help I'd greatly appreciate it.thx

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 740 Answers

SOURCE: New Mastercylinder/brakes still lose pressure

ITS THE MASTER CYLINDER AGAIN.More than likely they are using a re manufactured master cylinders. Get a new one from MOPAR-(CHRYSLER) that will take care of your problem. Trust me I have had the same problem with a similar vehicle in the past in my shop. Good Luck, thank for using FIX YA

Posted on Jan 16, 2009

Ad
  • 1861 Answers

SOURCE: slite oil leak from rear valve cover gasket per dealer $650.00

Hello. Let me try to assist you the best I can, with the hope of achieving a FixYa rating from you for my assistance.

Changing the rear valve cover gasket on your vehicle would be not considered a "real" big job, but IS a time-consuming job.
In order to remove the rear cover, you first have to remove the intake plenum. If you do not remove the plenum, you can't get to the valve cover bolts that are under the plenum. After the plenum is off, the valve cover is easy to access. You will also need to replace the intake plenum gasket, if you do the job yourself.

I hope this information has satisfied your question.
Thanks for choosing FixYa for assistance!

Posted on Jan 28, 2009

  • 1 Answer

SOURCE: 2003 town and country brake problem

Did your mechanic use a DRB III or equivalent scanner before performing the bleeding procedure after installing the master cylinder? This is a requirement by the manufacturer (Chrysler) when bleeding the brake system.

Posted on May 15, 2009

blueextc3221
  • 15935 Answers

SOURCE: Rearview mirror fell off windshield! Not broken...

the mirror should simply slide over the metal mount (button) that is glued to the window.

loosen the set screw on the mirror mount...

hold the rear view mirror mount on the glass just above the metal mount (wide end of plastic opening facing down)

slide it into place...
secure it by tightening down set screw you loosened earlier.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 22, 2009

canbruce75
  • 1776 Answers

SOURCE: I have never changed brake pads before in any car!

Piece of cake....you can do it! I would register at autozone.com. It's free and you can access a full online repair manual. Anytime I purchase a different car I also purchase a Haynes Repair Manual. These are also available at auto parts stores. It will give step by step instructions for your particular make and model of car. Hope this helps and good luck.

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the wiper relay in a 2003 honda odyssey


the relay box in under the hood near to the battery , remove the cover flip over it has a diagram showing the position to find the relay wiper switch fuse. small cube shape can easily be removed or replace

Feb 16, 2015 | 2003 Honda Odyssey

1 Answer

Windshield washer liquid leaking


Could be a couple of things ,,,, If the washer resevoir frooze in the recent past it could have split the motor/bottle or hoses attached, it may also be the anti return valve (Y shaped) on the hose work split and causing a drip !

Aug 26, 2012 | 2003 Acura 3.2TL

1 Answer

I just read an answer post you had made in response to a question about a 2003 Chevy Astro van vacuum line keeping the vents from switching from defrost to floor, to dash vents, etc., you mentioned...


I didn't initially answer your question, or even read it but I know what you are talking about. The source vacuum to the HVAC system inside the van. It attaches to a vacuum port on the left side of the engine just above valve cover attached to a bracket. They are very brittle plastic and break easily. I found it better to replace the vacuum line with small rubber line, such as washer fluid hose. Its easier to route and can be installed without bending plastic. Feed it from the left side vacuum "T" above the left valve cover, over to the heater valve on the right side in heater hose split. Its the source vacuum to inside, and if lost it defaults to the defrost mode and won't change modes.

Jan 29, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

My 2003 bmw 325xi has a oil smell inside the car. no oil spots on garage floor but oil is needed once a month.


A small amount of oil could be leaking from valve cover on to hot manifold, the oil would burn off leaving a oil smell that could permiate car interior.

Jul 29, 2010 | 2003 BMW 325

1 Answer

My 2006 Town Car is leaking a small amount of oil. Garage has checked and replaced oil plug and tightened oil filter but I am still noticing small 1/2 dollar bill size leak on garage floor. Any ideas? Cost...


Check for stains in the valve cover gasket on the side of the oil filter, and in the engine block right above the filter. There is not much that can leak on that side, other than filter itself, and you already checked it. You HAVE to take the car to dealer for warranty inpection, and repair. The issue not only has to be covered by warranty, but by not doing so in time, it might void the warranty, for being careless about it.

Dec 26, 2009 | 2006 Lincoln Town Car

1 Answer

The battery is on my 2004 Honda Odyssey. I need to jump start the car. It is nose into the garage all the way to the wall. I can't get it into neutral in order to push it out of the garage. Is there a...


YES. using a small screw driver or your finger nail, at the top of the cover on the steering column, just before the speedomter is a small cover, take that cover off, now take the ign key and push it in the slot, hold the key down and now the shifter should now come out of park.

Oct 17, 2009 | 2004 Honda Odyssey

2 Answers

2003 expedition Broken coil bolt Brass Insert


what engine?

4.6L/5.4L 2 valve

Is this the bolt you are talking about?

4e7257b.gif
5.4L 4 valve

or this?

07a7355.gif
If the top one, I think you could replace the insert

Aug 11, 2009 | 2003 Ford Expedition

1 Answer

2003 passat wagon rear window washer leaks


Hi
I have had this problem as well as many others with the passat Solved it as follows
First take out 2 philips screws inside the pull down hand grips ( hidden by covers) and 2 by the rear window surround
Then pull the rear panel of it is secure by metal clips, a 3 foot length of 2x1 timber with an angled ends helps to release the ones nearest the window
The washer pipe just pushes on the back of the wiper assembly
The most common reason it comes off is because of not using sufficient anti freeze additive in the washer water, inside the washer motor drive spindle is a small brass pipe which freezes in cold weathe and when you use washer the pressure pushes the pipe off
It an other one of volkswagens stupid designs a long with putting all the vunerable electronics in a box in the footwell which then floods when the drain under the battery gets blocked with debris!!!!
Steve
In UK

Feb 09, 2009 | 2003 Volkswagen Passat

1 Answer

Need a diagram of rear disc brakes


Replaced rear drum brake 97 f150 4x4. A spacer/washer oval in shape with 2 notches on outer edge and a rectangular hole in center. Where did it come from? Fell out while taking drum off.

Jul 21, 2008 | Ford Mustang Cars & Trucks

1 Answer

Honda Accord 1991 idles high then low


)The fact that thge engine idle fluctuates when it is cold indicates that the Fast Idle THermo Valve is out of adjustment.
This valve is located ot the front of the intake manifold on the driver's side just below the accelerator cable. To adjust it, wait until the engine is cold (best to do it first thing in the morning).
Remove the two screws holding the cover on and start the engine. There is a brass needle sticking up through a plastic ring that has two slots in it. With the engine idle fluctuating, use a thin flat blade screwdriver to SLOWLY turn the ring CLOCKWISE
until the idle stabilizes. Once done. put the cover back on withg the two screws and you should be done.

Jun 04, 2008 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...