Question about Cars & Trucks

Open Question

Where can I purchase a replacement globe for my D722 Pushlite Friedland D7222 pushlite door push... post code is 5041

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace park bulb.vt commodore


To replace the front parklight globe on a vt commodore can be a little tricky.

1.turn the lights on to see which 1 is inoperative once you know turn lights off.
2.open bonnet
3.go to side that is inoperative and on the back of the headlight you will see a round large plastic cover turn this to release it.
4.under the headlight globe there will be 2 wires flow these to the park globe socket gently twist and pull it out.
5.once the sockets out and you can see the globe ,pull the globe out of socket.
6.push new globe into socket
7.refit the socket in headlight
8.refit all trims
9.turn lights on make sure new globe is work..

Jan 22, 2014 | Cars & Trucks

1 Answer

Wiring diagram friedland door chimes


These are installation and wiring instructions for the Friedland 954 Door chime.

wiring-diagram-friedland-door-chimes-k3ydjvglpspjo3gx23qxrs40-1-0.jpg wiring-diagram-friedland-door-chimes-k3ydjvglpspjo3gx23qxrs40-1-2.jpg wiring-diagram-friedland-door-chimes-k3ydjvglpspjo3gx23qxrs40-1-5.jpg wiring-diagram-friedland-door-chimes-k3ydjvglpspjo3gx23qxrs40-1-9.jpg

Jun 24, 2013 | Cars & Trucks

1 Answer

Replace tail light globe holden astra 2005


remove inside black plastic triangle pieces under carpet or service flap light assembly then comes out and you now can get globes out
or some have plastic clips on side of globe holder assembly that you push out while pulling on globe holder assembly depends on what assembly you have

Jan 30, 2013 | 2004 Holden Astra

1 Answer

The brake light on my dash stays on even when the emergency brake is off. THe interior light sometimes goes on when the door is opened, sometimes doesn't and the ignition light doesn't always come on


The handbrake warning light is activated by a switch on the handbrake bracket under the console. This is most likely stuck or broken.

The interior light staying off when the door opens is common. It could be that a door plunger switch is sticking (they can corrode inside), or there is poor contact at each end of the dome light globe. Take out the globe and press the contacts closer (just a bit) then push the globe back in, checking that it is firmly held. Then spray a little WD40 or similar on the plunger of each door switch and press it in a few times against the spring.

Which ignition light is not working, one of the warning lights? Or the check engine light?

Dec 25, 2011 | 1995 Toyota Camry

2 Answers

Message centre posted "check stop lamp" what does


Sounds like you have a blown brake light globe. Often the brake light circuit electrical resistance is monitored and will have detected a blown globe (bulb) Have someone put their foot on the brake pedal and make sure all the brake lights are working. If not replace the faulty globe or repair the fault. Blown brake light globes on a few modern vehicles can cause many engine running faults which seem unrelated to the brake lights.

Mar 07, 2011 | 2004 Volvo XC90

1 Answer

Tail light is burned out on tail light. I have the bulbs but can't figure out how to remove and replace burned out light.


  1. Check with your local auto parts store or look in your owner's manual to find the proper model number of the replacement tail light globe.

  2. Open your trunk or lift your hatchback. Find the cover just on the inside of your vehicle next to the burnt-out bulb.

  3. Turn the two latches counterclockwise to open them so the cover may be removed. In most cases you can turn the latches with your fingers; in some cases you may need a coin or a slot screwdriver to turn them. Remove the cover.

  4. Press the tabs that allow you to remove the tray that holds the tail light globes. There are four tabs on most VW models. Each tab must be depressed to release the tray. Pull the tray out a few inches, as far as the wiring allows.

  5. Press down slightly on the burned-out globe and turn it counterclockwise with your thumb and fingers. It should release easily and then pull straight out. Push the replacement bulb in and turn it clockwise until it locks in place.

  6. Snap the tail light tray back in place. The tray should simply push back into place and the four tabs should "snap" into their locked position. Replace the door cover and turn the door locks clockwise. Test your bulb to see that it is working.

Good Luck

Nov 20, 2010 | 2004 Volkswagen Beetle

1 Answer

How to replace heahlight bulb in a 1994 Audi What bulb do i purchase? How do i release the clip that holds the light unit in place?


I replaced my globes not so long back.
The metal clip you simply push down. Replacing the left light is challenging as the air intake is in the way but its not impossible. After removing the clip there is a plastic cap. Remove it.
Then remove the cable that feeds power. You should be able to see the rear of the 'globe'. There is another spring loaded metal clip holding the 'globe' in place. Push the two ends of the clip together to remove this clip. The globe should be free now. Remeber the globe go in a specific way, so take note. I bought to Halogen globes for my Audi as these immitted a stronger beam. Please, whatever you do DO NOT TOUCH THE NEW GLOBES GLASS. The natural oil from your fingers will impact the lifespan of these and you'll have to replace these again. Remember to also reallign the beams.

May 26, 2010 | 1994 Audi Cabriolet

1 Answer

Replace headlight bulb 2006 Point


Under hood, remove large plastic wether cap from back of light, remove 3 point lug from unit, depress the rounded end of the retaining spring inside the open area,
while depressing it push it over to one side to release the pressure off the globe, remove globe, new globe will fit in only one position, be careful not to touch globes end with fingers as the oil in your skin is dtremental to its operation. assmbly is then in reverse. Good luck

Nov 20, 2009 | 2006 Pontiac Grand Prix

1 Answer

How do I replace the headlights on a 1988 town car?


Under hood, remove large plastic wether cap from back of light, remove 3 point lug from unit, depress the rounded end of the retaining spring inside the open area,
while depressing it push it over to one side to release the pressure off the globe, remove globe, new globe will fit in only one position, be careful not to touch globes end with fingers as the oil in your skin is dtremental to its operation. assmbly is then in reverse. Good luck

Nov 20, 2009 | 1998 Lincoln Town Car

1 Answer

Mitsubishi TH Magna 4 door Disassembling the dash to replace blown light globes. Where are the screws or bolts?


if you dont see any(look real hard) then you probably can just pull up or out and it will just come out,Some dashes after 2000 are pushed in type.

Jul 23, 2009 | Mitsubishi Passenger Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...