Question about Cars & Trucks

Open Question

Air bag electrical connections diagram? - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 lincoln town car no horn or cruise control all the fuses are good


Could be the clock spring assembly in the steering column . Do you know what that is ? The clock spring allows the buttons on the steering column to be connected to the vehicle .
How cars clock spring works
Testing the electrical with a DVOM -digital volt ohm meter is the proper way to diagnose electrical systems . Viewing wiring diagrams to see where connections are for easy testing of the circuit .

http://www.bbbind.com/free_tsb.html Enter vehicle info . year , make , model engine . Under system click on engine ,then under subsystem click on speed controls . Hit the search button , then click the blue link .Scroll down to second diagram an you will see the air bag slide contacts . This is a clock spring I think , never had your type vehicle apart . Do you also have a air bag light on ?

VEHICLE RELAYS Operation Diagnosis

Apr 25, 2017 | Lincoln Cars & Trucks

1 Answer

Trouble codes for 2006 ford foucos


p2258 - Secondary Air Injection System Control 'A' Circuit High
Possible causes - Faulty Secondary Air System Relay - Secondary Air System Relay harness is open or shorted - Secondary Air System Relay circuit poor electrical connection - Faulty Secondary Air System Pump

B1934 - Air Bag Driver Inflator Circuit Resistance Low on Squib

B1935 35 Passenger Air Bag Circuit Resistance Low Go To Pinpoint Test K

B2232 - Air Bag Driver Circuit Open - Loop #2 0 ' Add Comment Possible causes - Faulty Clock spring
Possible symptoms - Air Bag Warning Light ON

Dec 16, 2016 | 2006 Ford Focus

1 Answer

How do you disable air bag on 95 crown victoria


1992-98

CAUTION The air bag system must be disarmed before performing service around air bag components or wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary repairs and/or personal injury.
  1. Position the vehicle with the front wheels in a straight ahead position.
  2. Disconnect the negative battery cable.
  3. Disconnect the positive battery cable.
  4. Wait at least one minute for the air bag back-up power supply to drain before continuing.
    1. Remove the air bag module retaining bolts. Detach the electrical connector and remove the module.
    2. Attach air bag simulator tool 105-00010 or equivalent, to the vehicle harness connector.

  5. Connect the positive, then the negative battery cables.

Jun 27, 2012 | 1995 Ford Crown Victoria

2 Answers

Steering wheel adjustment , the steering whell is 90degrees off but the car does not pull eather direction. car was stolen no damage just steering whell truned


jack front of car up then turn steering wheel full lock to full lock and count the number of turns from either side then divide by 2 so you have the straight ahead position then remove the steering wheel and replace in the straight ahead position ,iam saying this because the vehicle may have been re tracked and only one track rod end adjusted so you have say 2 turns to the left and 2 and half to the right if you follow me .or remove the steering wheel then just hold it on and slowly drive forewards and lift wheel and refit to the correct position

Feb 10, 2011 | 1999 Mercury Grand Marquis

1 Answer

I want to find out where the fuse box is on my 2008 Toyota rav4 V6 engine and the location of the fuse for the air bags. I recently had surgery and opened chest so if air bag went off accidentally or...


Hey Doug ! I hope you're recovering fast and I wish you good health! Coming back to your problem ! Well I'll show you the link where you can find the electrical wiring on your RAV4 ! The diagram is of f a RAV4 but a 2003 Model ! As the manufacturer hasn't changed much of the electrical wiring layout, you won't find much difference in the two !
http://rav4faq.kerkerinck.de/xa2/tsb/files/BE3010_0_1_ElectricalWiringDiagramCLA20_Ergaenzung.pdf
A19 is the driver's Airbag connection. You could easily lead up to the fuse board and disconnect it.
Hope that solves your problem !
=)

Feb 02, 2011 | 2008 Toyota RAV4

1 Answer

My girlfriends car well the horn stop working?


Go to the horn remove the electrical connectors and jump it directly to the battery. if it works then you have to get the wiring diagram for the horn and check for B+ at the electrical connector to the horn,fuse and relay.
If all is good before you go to the horn switch protected by an air bag on the steering wheel READ THE SHOP MANUAL on stabilizing the air bag before you check out this switch. Remember this could be a $1200 dollar mistake if you deploy that air bag so be careful. Any problems write back I'll get you threw it.

Mar 07, 2010 | 1989 Honda Prelude

1 Answer

Rear suspension compressor turns on when without ignition


The compressor turns on when the height level switch closes. This is most likely occuring because the air bags are leaking air.

Nov 14, 2009 | 1992 Buick Park Avenue

1 Answer

Air bag light flashing (red)


Airbags dont need to be replaced. There is an issue with the electrical that connects to the airbags. This is not a DIY project because if you connect the wrong wires it could cause the bags to deploy and you could get seriously hurt - or cost $3,000 if your lucky to replace the bags

May 12, 2009 | 1995 Nissan Altima

1 Answer

How do you remove or replace the passenger airbag on a 99 contour , Is it a whole dash unit? What holds the drivers bag in the steering wheel? I assumed it was a tork but not sure. Where is the control...


Please rate as fixya if this helps.
the air bag control module is under the console.

  1. Disconnect the battery ground cable.
    1. Wait one minute.
  2. Remove the center console. For additional information, refer to Section 501-12 .
-----------------------------------------------------------------
  1. Disconnect the battery ground cable.
  2. Wait one minute.
  3. NOTE: Contour shown, SVT similar.
    Remove the rear floor console screws.
    1. Move seat fully forward.
  1. Fully apply the parking brake.
  1. Detach the shift indicator selector bezel.
  1. Detach the shift bezel from the selector housing.
    1. Remove three bolts.
    1. Detach shift bezel from the console.
  1. NOTE: The rear floor console must be raised to disengage the front retaining clips.
    Raise and remove the rear floor console.
  1. Remove the four front floor console retaining screws.
  1. Detach the front floor console.
    1. Set the gearshift lever into position 1.
      Partially remove the front floor console.
  1. Disconnect the cigar lighter electrical connections and remove the front center console
-----------------------------------------------------------
  1. Disconnect the air bag control module electrical connectors.
    1. Depress the locking tang.
    1. Slide the locking bar back.
    • Disconnect the connector.
  1. NOTE: The air bag control control module is grounded by the retaining bolts.
    Remove the air bag control module.
    • Remove the three bolts.
--------------------------------------------------------------------------------------------
driver air bag module

  1. Disconnect the battery cables.
  1. Rotate the steering wheel 90 degrees to access and remove the Torx screw. Rotate the steering wheel 180 degrees to access and remove the Torx screws.
  1. Remove the driver air bag module.
    • Disconnect the electrical connector.
    • Remove the air bag module.
------------------------------------------------------------------------------------------
  1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
  1. Open the glove compartment, press the sides inward and lower the glove compartment to the floor.
  1. Remove the passenger air vent duct.
    1. Disconnect the duct from the heater box housing.
    1. Disconnect the duct from the instrument panel register and remove.
29e093f.gif
  1. Disconnect the passenger air bag module electrical connector.
  1. Remove the two retaining bolts securing the rear of the passenger air bag module to the cross-vehicle beam.
14df419.gif
  1. sxp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the passenger air bag module when removing the retaining nuts.
    Remove the two nuts from the front of the passenger air bag module.
4a697c8.gif
  1. Remove the passenger air bag module.
    • Lower the front edge of the passenger air bag module, roll the passenger air bag module around the cross-vehicle beam lowering it into the passenger footwell.
82a0ae0.gif

Mar 15, 2009 | 1999 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...