Question about Cars & Trucks

Open Question

How do i get the control and radio panel off - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the signal light relay that makes signal lights flash located on 2000 ols intrigue 3.5 liter


Important: The hazard warning switch includes the turn signal and hazard warning flashers.
Removal Procedure
Remove the center air deflector. Refer to Instrument Panel Center Air Outlet Deflector Replacement .
Squeeze the retainer on the backside of hazard warning and cruise control switch.
Pull the hazard warning and cruise control switch from the retainer in the instrument panel.
Disconnect the electrical connectors from the hazard warning and cruise control switch.
Remove the hazard warning and cruise control switch from instrument panel.
Remove the hazard warning and cruise control switch bezel from the instrument panel trim pad by using a small flat-bladed tool to the release retainers.
Remove the radio. Refer to Radio Replacement in Entertainment.
Reach through the radio opening and push the retainers up towards the roof of the vehicle. When the retainers release, slide the instrument panel (I/P) center air outlet deflector out of the I/P opening
Remove the air outlet deflector
Remove the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement in Instrument Panel, Gauges, and Console.
Remove the bolts from the radio.
Pull the radio toward you.
Remove the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
Pull the instrument panel (IP) accessory trim plate away from the IP trim pad.
Disconnect the IP harness seat heater leads, if equipped.
Remove the seat heater switches from the IP accessory trim plate, if equipped.
Remove the IP accessory trim plate.

Nov 09, 2016 | Cars & Trucks

1 Answer

How do i remove a radio from a 1993 suzuki sidekick


well thats in the FSM. easy peasy
stock radio , we cant do non stock. (vast )
i guess step 4 is it?

heater control page.
  1. Disconnect the negative battery cable.
  2. If equipped, disable the air bag system. (skip)
  3. Carefully pull the knobs off of the control levers.
  4. On Sidekick, Tracker, Sidekick Sport and X-90 models, grasp the trim panel and pull it off of the instrument panel.
  5. stop.... here.
radio out
electronic version not analog
remove ash tray, and hidden tray screw and tray guide

  1. Pull the heater control lever knobs off of the levers.
  2. On 1996-98 models, separate the heater control trim panel from the control unit by pulling it straight away from the instrument panel. Allow the trim panel to hang loose.
  3. Open the ashtray, then depress the ashtray retainer and remove the ashtray from the sliding track. While it is removed from the vehicle, now would be a good time to wash it out.
  4. Loosen the two retaining screws, then remove the ashtray track from the instrument panel center trim bezel.
  5. On 1989-95 Sidekick and Tracker models, remove the trim panel (Bezel) by prying it carefully away from the instrument panel.
  6. On 1996-98 models, remove the center trim bezel from the instrument panel by loosening the four retaining screws and maneuvering the heater control trim through the appropriate hole. Set the bezel out of the way.
  7. Use a screwdriver to loosen the one rear mounting bracket-to-radio screw; access can be gained to this screw through the ashtray hole.
  8. Remove the four radio front retaining screws, then pull the radio out of the instrument panel just far enough so that the electrical connections on the rear of the radio can be accessed.
  9. Detach and label the wiring from the radio. Also, detach the antenna cable from the rear face of the radio
  10. pull radio. now. (if stock if not stock look for locks)


step 5
25477768-tiechxycrusckuccgw3t0yzs-2-0.jpg

Feb 25, 2015 | 1993 Suzuki Sidekick

1 Answer

How do i remove the stock radio from my 1993 geo metro 4 door hatchback


here is the online fsm quote

  1. Disconnect the negative battery cable.
  2. Open the glove box. Remove the glove box open panel.
  3. Remove the air conditioning switch connector and heater control unit lever knobs. Pull heater control unit cover plate from instrument panel.
  4. Remove the gearshift control lever upper boot and center console.
  5. Remove the ashtray.
  6. Remove the instrument panel center trim bezel and radio face plate.
  7. Remove the screw from the back of the radio receiver and the screws from the front face of the radio.
  8. Remove the radio.

Sep 30, 2014 | 1993 Geo Metro

1 Answer

Radio control panel works intermittantly


partly remove radio unit and check the earth wire is tight.

Oct 24, 2012 | 2009 Honda Pilot

1 Answer

How do I fix the light in the heater control?


The heater control will have to be removed and possibly disassembled to get at the bulb.

1995-98 Models
  1. Disconnect the negative battery cable.
  2. Remove the radio/HVAC controller cover by depressing the center pins inward to release the push pin fasteners. Be careful not to push the center pins all the way through the fasteners.
  3. Remove the push pin fasteners and pull the radio/HVAC controller cover rearward.
  4. If equipped, disengage the traction control/fog lamps/rear defogger electrical connector.
  5. Remove the radio. Refer to the Radio removal and installation procedure, later in this section.
  6. Disengage the electrical connectors behind the controller face. Remove the wiring harness clip from the module boss.
  7. Disengage the temperature and mode cables from the controller assembly by squeezing the lock tabs together while pulling the cable housing straight up. Pull the cables straight up to disengage them from the control lever pins.
  8. Remove the HVAC control panel screws, then carefully pull the panel forward and remove it from the vehicle. To install:
  9. Position the HVAC control panel to the dashboard and install the retaining screws. Tighten the retaining screws to 22 inch lbs. (2.5 Nm).
  10. Install the white temperature and black mode cables over the pins.
  11. Install the cable housings into the clip grooves, then push down to lock them into position.
  12. Reattach the electrical connectors to the back of the control panel face. Install the wiring harness clip to the module boss. Be sure that the wiring harness does not bind with control lever movement.
  13. Install the radio.
  14. If equipped, reattach the traction control/fog lamps/rear defogger electrical connectors.
  15. Install the radio/HVAC controller cover by pushing in at the clip locations.
  16. Install and lock the push pin fasteners.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 26, 2010 | 1998 Saturn SL

1 Answer

How do i remove the radion on a 200 acura rl


You cann't remove only radio you have to remove whole panel which contains radio.

There are two possible scenarios for you car radio panel


1. Your car can have Navigator, Climate Controller and Radio.

2. Your car can have Climate Controller and Radio.

You have to open whole panel.

This Panel contains some of SRS components, so have to be very careful while removing it!

Please search for "Acura RL Service Manual"

Follow this link you will be able to download it for free.

http://rapidshare.com/files/55768439/1996-2004__Acura3.5RL_Service_Manual.rar.html

PLEASE RATE!

May 21, 2010 | 2000 Acura 3.5RL

1 Answer

Stock radio


removed the panel below the radio, clips hold it in and you have to yank it out without damage. then there are two 8mm head bolts behind that panel facing up. they hold the whole frame for the audio and climate controls. then push on that frame with your fingers to pop out the whole panel that the radio and the climate controls are mounted to. then simply disconnect the harnesses and remove the climate controls(three screws and the dials pop off). now you can get to the four 8mm bolts that hold the audio unit in.

Mar 05, 2010 | 2003 Honda Civic

2 Answers

How do I get the factory radio out , so I can put


Removal & Installation You will need radio removing tool T87P-19061-A or its equivalent to perform this procedure.
  1. Disconnect the negative battery cable.
  2. Place the temperature control switch to the COLD position.
  3. Unlock the temperature cable by pulling down on the tab.
  4. Disconnect the cable while holding the tab down.
  5. Using the radio removal tool, pull the integrated control panel from the instrument panel.
  6. Unplug the vacuum harness, antenna lead and the electrical connections from the rear of the control panel.
  7. Remove the control panel.
To install:
  1. Attach the vacuum harness, antenna lead and the electrical connections to the rear of the control panel.
  2. Install the control panel into the instrument panel.
  3. Connect the temperature control cable.
  4. Connect the negative battery cable

Jan 19, 2010 | 1999 Ford Escort

1 Answer

I have a 1996 Cadillac Seville SLS and I want to remove the radio and a website said I would just have to pull the trim around the radio and heater out and it would expose screws that would allow me to...


  • Remove the heater and A/C control and radio bracket fasteners.
  • Partially remove the radio and A/C control assembly.
  • Disconnect the electrical connectors from the radio and A/C control assembly.
  • Remove the radio and A/C control assembly.

  • 288103.gif
    tif.gif
  • Remove the radio retaining nuts.
  • Remove the radio from the radio bracket.
  • Installation Procedure Install the radio to the radio bracket.

    288103.gif

      tif.gif
      Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    Install the radio retaining nuts.
      Tighten
      Tighten the radio retaining nuts to 10 N·m (88 lb in).

      287815.gif
      tif.gif
    Partially install the radio and A/C control assembly.
    Connect the electrical connectors to the radio and A/C control assembly.
    Install the radio and A/C control assembly.
    Install the heater and A/C control and radio bracket fasteners.
    Install the console trim plate. Refer to Console Trim Plate Replacement in Instrument Panel, Gauges and Console.
    Install the instrument panel center trim plate. Refer to Instrument Panel Center Trim Panel Replacement in Instrument Panel, Gauges and Console.

    Jun 29, 2009 | 2001 Cadillac DeVille

    1 Answer

    1996 accord control panel


    Remove the center consule up to the radio. Remove the glove compartment. This will free up the radio consule. From there, you can remove the AC control panel

    Jun 16, 2009 | 1996 Honda Accord

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    16 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...