Question about Cars & Trucks

1 Answer

Vaccume stamatics for 1998 2.5 liter contour

Vaccume lines from egr to intake

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,673 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Antifreeze getting into throttle body


The 3.8 liter for this year has a plastic intake manifold. These manifolds are known to fail around the EGR port. When this happens coolant will leak into the intake right behind the throttle body. Dorman makes a replacement upper plenum that has been reinforced in this problem as along with a new gasket and an updated EGR tube. This will more than likely solve your issue. If you see a little coolant behind the throttle body this repair needs to be done ASAP. If this area completely ruptures it will hydroloc the engine. This means that coolant will fill one or more of the cylinders and the engine will not turn over/start.

Nov 03, 2012 | 1998 Oldsmobile 88

1 Answer

I cant find the EGR valve on my 1998 Ford Contour SE. Supposed to be on the intake manifold but I dont see it anywhere. Also should be a line to it from the exhuast manifold but I dont see one. Engine is...


It has to have a tube or pipe going to it
from the exhaust manifold

It has to have vacuum hoses going to it
That is a dead give away

It could have a wiring harness connected to it.

As you said it has to let exhaust gases into the intake

Look for a picture on the internet or ask a neighbor
to show you

Jun 27, 2011 | 1998 Ford Contour

2 Answers

On a 1998 ford contour what is the line that run from the intake to break booster


This is the vacuum line that boost the pressure you apply to the pedal. In other words, without this line you do not have power brakes.

Feb 09, 2011 | 1998 Ford Contour

1 Answer

What is code po171 on a 1998 Ford expedition


refers to o2 sensor bank 1 s1 is reading lean check for exh leak vaccume leak egr intake check for misfire


let me know if this helps comment reply if you need more info

Jan 18, 2011 | 1998 Ford Expedition

1 Answer

If the EGR vacuum salenoid valve is failed would is cause it stall at low speed


yes it will remove vaccume line to egr if you can and egr will close if solenoid is attatched to egr then you have to replace egr valve

Jan 14, 2011 | 1998 Mercury Grand Marquis

2 Answers

1998 dodge ram error code 1494 check engine light on and poor gas mileage


Check all tubing and junctions for leaks in the fuel evaporation control system. The ECU has detected an issue with intake manifold pressure and is indicating that fuel vapour recovery system is perhaps to blame. Sometimes this can be connected to a fault in the manifold differential pressure circuit which lies on the vacuum line leading to the EGR valve. Also quickly check that the EGR (exhaust gas recirculation) valve is OK by connecting and reconnecting its vacuum line and listening to engine note changes. No engine note change indicates the EGR is probably jammed shut with exhaust crud and needs a general clean up. Sometime these codes detect the symptom and not the cause so you just have to work your way back and eliminate what it might be.

May 07, 2010 | 1998 Dodge Ram 2500 2WD

1 Answer

1998 saturn s2 wagon revs high and then shuts off


Most likely you have a leak, its either a vaccum leak (could be the intake manifold, or most likely it is just a PCV Line, these are hoses leading from the Head cover to the intake manifold) or leaking EGR (exhaust Gas Recirculation) valve.

Feb 04, 2010 | 1998 Saturn SW

1 Answer

98 ford ranger xl 2.5 liter


did you check to make sure everything is plugged in like for instance the tps(throttle position sensor)? did you plug the temp sensor(it's on the intake near the thermostat housing)?did you somehow disconnect a vaccum hose to the intake(check the EGR valve)? check to make sure all your plug wires are on tight. keep me posted

Sep 06, 2008 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...