Question about Ford F-250

1 Answer

02 ford 250 7.3 want crank replaced cam sensor,fuel filter,checked fuses and relay,has oil pressure when trying to crank,everything works except tac and check engine light does not come on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,680 Answers

Did you check battery crank power?Could be starter,

Posted on May 04, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will the oil pressure sensor prevent ignition to the motor? 1999 Ford Laser - KN or Mazda 323


no oil sensor not related

fuel ,spark a broken timing belt

fuel
pump or relay you should be able to hear the fuel pump working
if engine light is on
crank angle sensor

Nov 05, 2016 | Ford Cars & Trucks

1 Answer

Why my 97' f-250 7.3 powerr stroke keeps dieing while idling


The power stroke engine has several things that will cause this problem #1 crank shaft sensor AKA cam shaft sensor on crank shaft located on passenger side of engine near crank shaft pulley # 2 IPC sensor Injection pressure control if has oil in sensor replace it & wiring pigtail .#3 high pressure oil pump not up to par. #4 injection pressure regulator solenoid they get sticky. with a good scanner that has FORD enhanced software you can check all of these without leaving the drivers seat and perform running tests on injectors and test the ficm module interface with the pcm. Fuel Injection Control Module & Power Control Module.

May 02, 2014 | Cars & Trucks

1 Answer

Ford F250 2002 7.3 Diesel won't start


check engine immobiliser and crank position sensor . Run fault codes and replace faulty units.

Apr 04, 2013 | Ford Cars & Trucks

2 Answers

My 02 chevy cavalier turns over but will not start. I have replaced ever thing i know that could be wrong.


does it produce fire does the gas pressure rise does the crank sensor and cam sensor work

Feb 09, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Replaced everything under the sun on our 87 olds delta 88...wont fire on its own but will fire and run fine as long as u shoot it with starter fluid. We replaced starter, fuel pump, filter, plugs, wires,...


Can you here the fuel pump running?no, check fuse,and pump relay. Check pump fuel pressure,at the fuel injector rail,or throttle body. Check for voltage at the top wiring on the fuel nozzel.While cranking look for pulsating voltage.None, test computer,scan system. let me know the outcome.

Aug 30, 2010 | 1987 Oldsmobile Delta 88

1 Answer

Replaced motor on 2004 suburban and roll over except not starting


If one of the coils are bad the computer will send a code that can be read with a scan tool. Check this and also check your fuel pressure reading with a pressure gauge hooked up to make sure you have pressure from the fuel pump. Even if you hear it, it may not be putting out the correct pressure or fuel filter could be clogged, the sock on the fuel pump could be collapsed, or could just have an air lock in the fuel system. Maybe try pulling the air horn on your throttle body and pouring a VERY small amount of gas into it to force fire while you are cranking. Good luck and hope this helps.

Jul 06, 2010 | 2004 Chevrolet Suburban

1 Answer

Engine cranks,has spark,fuel and oil pressure.changed oil pressure switch,crank and cam sensor,spark plugs and ignition relay.checked electrical connections and all fuses.


most cars have a mass airflow sensor.try reploacing that,That is the only other thing i can think of besides what was already replaced. if this does not work get a compression test done on the car.

Feb 09, 2010 | 2006 Nissan Sentra

2 Answers

97 Ford F-250 - turns over but won't start


Did you check for spark? Ignition coil? Ignition control module.

Sep 02, 2009 | 1985 Ford F 250

1 Answer

Wont start but cranks


I dont know if you have tried this, but first change the glow plugs, if that doesnt work or you have tried that, then clean off the terminal where the glow plug cables attach to by the battery. Hope this helps

Mar 17, 2009 | 1985 Ford F 250

2 Answers

2003 chevy malibu that cranks but won't run


If you haven't done so already, have the cam and crank shaft position sensors checked, or replaced, You have replaced everything else.

Jan 27, 2009 | 2003 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...