Question about Toyota Cars & Trucks

Open Question

How to reset timing belt warning light for Toyota super custom model1995 1kz engine

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: How to reset timing belt light

to reset the light you need to remove speedo dash assembly ,on the back of the printed curcuit there is a small screw and a hole next to it remove screw and fit to empty hole . refit assembly

Posted on May 07, 2009

  • 115 Answers

SOURCE: code 1346 on 2002 toyota sienna

P1346 is the code for:
VVT Sensor /Camshaft Position Sensor Circuit Range/ Performance Problem (Bank 1)
If the code came on just after the timing belt replacement more than likely the sensor was damged in some way during the work. The sensor is located in the same area the mechanic was working in while changeing the timing belt. You should have this checked right away. A faulty cam sensor can also lead to the vehicle not starting.

Posted on Sep 04, 2009

Testimonial: "thanks sounds good"

  • 1 Answer

SOURCE: Timing belt light of Toyota LandCruiser 2006

the reset procedure of the timing belt light is all done by pressing the trip meter button and holding it in whilst the ignition is turned to on then select from the trip button then continue pressing until you come to 15 on trip metre, turn off and then restart. The light should then go off.

Posted on Jan 13, 2010

  • 1 Answer

SOURCE: How do I reset the timing belt warning light in a

how to reset timing belt warning light in a toyota hilux model LN 145

Posted on Sep 11, 2010

  • 62 Answers

SOURCE: 2008 Toyota Prado - timing

Remove instrument panel, at rear is indicated where to move screw from one position to the other!

Posted on Oct 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Timing belt warning light remains on


I'm assuming that you followed the lamps advice and replaced the timing belt. This indication comes on automatically every 150000km to remind you to replace the timing belt before it breaks and causes catastrophic engine damage. That being said, here is the procedure to reset the lamp for the next time.e14cc3b3-111d-48e9-ae93-9d93377ba748.jpg

Nov 08, 2013 | 2007 Toyota Hilux 2.7

1 Answer

Land cruiser 2010 timing belt warning light ON, how can reset?


not sure if thes will work for you but try it you wont lose any thing :

turn the key on hold the odometer button in and turn the key but don't start the engine and keep holding the button for 10 ten seconds then lift your finger off the button and the number 1 should come up now this number represents 10,000 K's so what you do is keep pushing the button until you reach the desired K's you want you can go up to 20 = 200,000 K's and then you hold the button in for another 10 seconds then let go and turn the key off and turn it back on and it should be gone i know this works because I've just done it today

Mar 26, 2013 | 2010 Toyota Land Cruiser

1 Answer

My toyota qualis shows T-Belt warning when i switch on ignition but it does not goes away when i start the engine is it OK


open the od meter timmig belt indicator shift in the side whole the tmmig belt light is reset next miles

May 14, 2012 | 2002 Toyota Tundra

1 Answer

How to turn off the timing belt light of a 3L engine


Have you replaced the timing belt? The warning light is a maintenance item that shouldn't be ignored. 60k is the average life span of a timing belt and if ignored and belt breaks you're in full a "wallet full" of repairs. Replace if you haven't, then have Toyota or service place reset the light. That's one light you shouldn't ignore.

Jan 04, 2011 | Toyota Land Cruiser Cars & Trucks

2 Answers

How do I reset the computers timing belt information in a Toyota 2007 4.7L (VIN T, 5th digit, 2UZFE eng, 8 cyl) after making a timing belt change?


1. T-BELT MODE DISPLAY
a) With ignition turned ON, using the trip switch (select/reset button) change the display to ODO, and turn the ignition OFF
b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds.
c) Release the trip switch, then press the switch again within 5 seconds.
d) The digital display should change to T-belt mode. The initial display "15" (0,000km) is displayed (ie. 150,000km).

2. REWRITING REPLACEMENT VALUES
While in the T-Belt mode, each press of the trip switch will change the displayed value by 10,000km increments. Once " 20 " (200,000km) is reached the display reverts back to " 1 " (10,000km) again. Remember, this setting is the number of kilometres to be travelled before the light comes on next, and once reset this counter will start from zero.
I believe the timing belt interval for all the 100 series engine variants is 150,000km, but this should be checked against each different markets servicing recommendation. This being the case, you shouldn't need to change from the default setting of "15".
Obviously for the US, the ODO is in miles, and I guess the T-Belt warning would be set in 10,000 mile intervals.

3. T-BELT WARNING RESET COMPLETION
a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch.
b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
NOTE: If the T-Belt mode is completed, even though the belt replacement has not been performed, the T-Belt warning IS reset.

Oct 30, 2010 | Toyota Tundra Cars & Trucks

2 Answers

How do I reset the timing belt warning light in a 2004 toyota prado 120 diesel


how to reset timing belt warning light in a toyota hilux model LN 145

Aug 29, 2009 | 2004 Toyota Land Cruiser

1 Answer

Don't know how to reset timing belt warning light after belt repl


You must remove the dash panel and you'll find a screw just behind the warning light. You have to swap the screw place...it's written at the back "timing belt reset".

Feb 08, 2009 | 1996 Toyota 4Runner

2 Answers

How to reset timing belt warning light of UZJ100 LANDCRUSER


what year what type ??? whats a holden ,i think its an opel now ,best advice remove the bulb

Nov 21, 2008 | 2006 Toyota Land Cruiser

1 Answer

Toyota Land Cruiser check timimg Belt


Hi,

I am assuming that you have a series 80 diesel engine and that it has run for about 100,000 kms hence the warning light and the changing of the timing belt. Based on the instructions of its repair manual you need to "remove the grommet off from the speedometer and turn off the lamp by pushing the warning light reset switch, then replace the grommet." Alternately, you can try to reset the entire computer of the vehicle by removing the battery cables for a couple of minutes. Pls note that some car radios/head units would revert to security default (ask for a code) when power is completely removed.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jun 24, 2008 | 1997 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...