Question about 1992 Acura Integra Hatchback

1 Answer

Brakes keep freezing; new brakes, rotors, calipers, etc.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Try rubber hoses

Posted on Jul 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My passenger side rotor is grinding against something when I drive it. Rotors and brake pads have just been changed but still having the problem. 2003 buick century...Any suggestions?


Did you check the calipers? If you have a caliper hanging up (not fully retracting after braking) it will give that kind of noise and you might even feel a slight tug to the side where the caliper is hanging up. Does the noise go away when you step on the brakes? if so that is diagnostinc for a faulty caliper. You can get a rebuilt one fairly reasonably I would think and it is easy to change. You will need to bleed the brake lines after changing. Keep the brake line plugged up and covered to keep dirt etc out of the system while disconnected.

Jun 03, 2014 | Cars & Trucks

1 Answer

Replace rear brake discs and pads


Depending on vehicle. Find level ground and park there. Put chocks in front and behind wheels not being lifted. Loosen lugs, jack up vehicle, set jack stands, lower vehicle on jack stands, remove lugs and wheel. Open hood remove brake fluid cap. Remove two bolts holding caliper, pull caliper off rotor disc and bracket, remove pads, place a used pad in front of caliper piston, use a c clamp to push caliper piston in caliper, remove c clamp and old pad, hang caliper up, remove 2 bolts holding caliper bracket, remove bracket, remove rotor, install new rotor, install caliper bracket, install new pads, install caliper, repeat this on other side, put cap back on brake fluid tank, remove bleeder fittings and keep pressing brake pedal until an even flow of brake fluid sprays out. Install bleeder fitting. Make sure brake fluid doesnt get on paint and is contained and disposed of correctly, top off fluid install wheels and raise car up remove jack stands, lower car and break in new pads

Nov 06, 2013 | Cars & Trucks

1 Answer

1994 Jeep GC rear drum brakes grab on damp days and low speeds. All hardware has been replaced including new shoes and drums.


The Caliper Adjustment Lever is what adjusts the caliper - ensuring the brakes pads are in proper placement to the rotor for effective braking. The lever must be cycled in order to keep the calipers adjusted properly. The only way the lever is cycled, is by the usage of the e-brake.


zjlimited_1187.jpg

Remove the cable from the Caliper Lever. Be careful when handling and removing the spring.

zjlimited_1188.jpg

The Caliper Adjustment Lever is what adjusts the caliper - ensuring the brakes pads are in proper placement to the rotor for effective braking. The lever must be cycled in order to keep the calipers adjusted properly. The only way the lever is cycled, is by the usage of the e-brake.



Initial testing: After you have removed the ebrake cable - kneel in front of the rotor and give it a gentle shake (as if you were removing it). Do you notice any PLAY between the pads & rotor?? Make note of this.



For the TSM kit caliper adjustment instructions - visit here: Troubleshooting.htm#2 and click on "Adjust Caliper Parking Brake".

Good luck.

May 05, 2011 | 1994 Jeep Grand Cherokee

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

How do I change front brakes on this vehicle?


Your model is not to involved with special needs or tools...The brake pads are exposed when you remove the front caliper...this is accomplished by removing the 2 mounting bolts completely, then lift the caliper off of the rotor...be sure to hang the caliper on a strut spring or something to keep it from falling or damaging the brake line...you can pull off the rotors on this model after removing the caliper...You need to push the pistons all the way in to use the new pads...channel locks can do this. I recommend that you include replacing the rotors as this will assure the smooth new operation of pads and rotors...the rotors are inexpensive at about $20-$25...use all lubricants in re-assembling the calipers, and grease your wheel studs for weather-proofing and future service. SPECIAL NOTE: After completion pump the brakes before driving...do not be surprised that the pedal initially goes to the floor...keep pumping to restore...check fluid in master cyclinder to be sure still full...congratulations on replacing your own brake parts and saving $$$$

Nov 24, 2010 | 1999 Plymouth Grand Voyager

1 Answer

How do you remove the front brake rotor on a 2005 Pontiac Vibe?


To remove the brake rotor, you must first remove the brake pads and caliper. There are two bolts that hold the brake caliper in place. Remove the two bolts and tie the caliper up out of the way. Be careful not to break the brake line connected to the back of caliper. Once the caliper is removed, simply slide the rotor off. To install a new rotor, simply slide rotor over studs and replace the caliper with new brake pads. It is as simple as that.

Jun 16, 2010 | 2005 Pontiac Vibe

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

2 Answers

Evaluting Brakes/Calipers and Rotors Front end shimmeys when applying brakes at all speeds...


the roiors are "warped" you could have them machined but the problem will come back and be worse due to thinner rotors. replace with new rotors.
and high quality brake pads. recomend the ceramic ones they are way more exspensive but last way longer, make less dust and noise and are able to better handle the heat produced by your driving situation. heat from exessive usage is what causes rotor warpage

Apr 28, 2010 | 2001 Dodge Dakota

1 Answer

I replaced the rear brake shoes on a 2003 Hyundai Sonata about 2 weeks ago. When I took them off...the passenger side was like new but the drivers side was worn badly. The inside shoe was worn but the...


Did you replace the rotor on the driver's side? If the rotor wasn't replaced or turned (to make the surface smooth again), the rotor may have chewed up the new brake pad.

The other possibility is that the caliper is not centering itself over the rotor, causing one side (outside) to do most of the braking. The caliper assembly has to be able to 'float' in order to keep itself centered. Check the guides that the caliper is mounted in for damage or corrosion that would keep the caliper from moving in/out.

Feb 03, 2010 | 2009 Hyundai Sonata

1 Answer

All new brake shoes on 97 jeep front callibers still sticking


The problem lays with the Caliper itself and/or the brake hose connected to the Caliper.
However if you replaced the pads, did you also replace the Rotors or have them Turned? The old pads wear the rotor. New pads on old rotors that have not been replaced or turned may end with rubbing or stuck brakes.
A simple way to test whether it's one and/or the other:
1. Remove the Caliper from the rotor, remove the pads. Keep for now the caliper attached to the brake hose.
2. Very slowly push on the brake, exposing more of the piston out of the bore. Not all the way. Usually until the rubber dust seal/boot is fully extended.
3. Check the seal/boot for cracks and tears, and if clean or not. Bad seals may prevent the piston from re-seating.
4. Using a c-clamp and pushing straight in: Try repushing the Caliper Piston back into the Caliper Bore (the cup back into the hole). It should go back in realitively easy.
5. If it doesn't go back in easy: Again slowly pump the brake and re-push the pistons back out to full extended seal/boot (but not the piston out of the bore).
6. Detached the brake hose from the caliper.
7. Again using a c-clamp and pushing straight in: Try again to repush the caliper piston back into the bore without the hose attached. If it goes back-in relatively easy - the caliper is okay...it is the brake hose.
8. If the caliper piston does not go back in easily - Replace the caliper.
9. When Installing the new (reman) caliper, remember to bleed the brakes.
TRY EITHER OR #10 OR #11 BELOW:
After the new Caliper is reattached to hose and has been bled:
10. Again push on the brake petal to fully extend the caliper piston fully (rubber seal/boot fully extended) Again do not push the piston out of the bore! Try pushing the piston back into the bore. If it does not re-seat relatively easy: Replace the brake hose.
11. Another method: After replacing the new caliper back on the rotor: Assumng the entire front end (2WD front wheel drive) or entire vehicle (2WD rear wheel drive) or (4WD all the time) is jacked up off the ground
a. Put the lug nuts back on the rotor.
b. Have helper Start the vehicle and place in Drive. Don't step on gas!
c. Have then let off the brake and then engage the brake.
d. When they let off the brake watch to see if the Rotor is turning or not, if rubbing or not. Or if still sticking.
e. With a new caliper, turned or new rotors, and still a problem? It is the brake hose!
12. Replace the brake hose and try again.

Another method but more expensive:
OR Replace the calipers, brake hoses; bleed and test!

If this helped or not; or if you need additional help or have addtional questions let me know on fixya.com!

Nov 28, 2009 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
1992 Acura Integra Hatchback Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...