Question about Toyota Cars & Trucks

Open Question

Please assist on how to perform static timing on toyota 4y engine with electronic distributor

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 78267 Answers

SOURCE: i need a diagram for a 4y Toyota engine

Go to the link please.

Posted on Aug 12, 2016


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need all torque settings for a toyota 4y 2.2 engine

try this site:

Mar 02, 2017 | Toyota Cars & Trucks

2 Answers

Timing on a 4y motor toyota forklift

images for Timing on a 4y motor toyota forklift

Timing Chain And Sprockets, Cover And Seal - AutoZone

AutoZoneToyota Cressida and Van 1983-1990. REMOVAL & ... 1 Exploded view of the timingcover assembly-3Y-EC and 4Y-EC engines. Click image to see an enlarged ...

How do you set the timing for a toyota 4y engine - Fixya
Jun 29, 2011 - Posted on Jun 29, 2011.

Nov 07, 2015 | Toyota Cars & Trucks

1 Answer

What could cause an 18month old distributor to break down in a 4Y engine

Usually it's caused by excessive resistance in the secondary circuit of the ignition system. The wires, spark plugs, low quality dist. cap, excessive moisture inside the distributor are common causes of premature failure you are experiencing.. Is there any engine oil inside the cap? This could easily cause it too. Ignition systems are designed to remain clean and dry. Check the end play on the distributor shaft to see if it is worn or able to move in any other way than in a circle---no side to side or up and down motion is permitted, if you have any of that, replace the distributor

Jan 02, 2015 | Toyota HiAce Cars & Trucks

1 Answer

How do i set the timing on a toyota 4y engine with an electronic ditributor?

Set No. 1 to TDC/COMPRESSION. To set in the following manner.
a. Remove No.1 spark plug.
b. Place your finger over the hole of the no.1 spark plug and rotate
the crankshaft clockwise to tdc. If pressure is felt on your finger
this is TDC/Compression of the no.1 cylinder. If not repeat the
c. Position the slot of the oil pump drive from 12 o clock looking
at it from the bolt that holds the distributor down should be
approx at 30 degrees to the right.
d. Align the groove of the housing with the drill mark of the driven
gear (not driven gear straight pin).
e. Insert the distributor, aligning the center of the flange with that
of the bolt hole on the cylinder block.
f. Also you can line up the no.1 marking of the cap to the rotor position
for no.1

Aug 06, 2014 | 1986 Toyota Hilux 2200

1 Answer

What is the head torque specifications?

You will be needing the specifications for a 4Y Toyota engine will be found in the workshop manual for a Toyota high lux that has the same engine in it.

May 10, 2014 | 2008 Isuzu i-Series

1 Answer

Toyota 4Y carburater problem float chamber drains over night

ive had the same problem, i just took off the carb and rebuilt it and never had a problem again

Jan 19, 2009 | 1984 Toyota Pickup Deluxe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides