Question about Mitsubishi Cars & Trucks

Open Question

What is splash problem in mitsubishi model mwk_07cv m

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Our 2004 Mitsubishi Endeavor continues to leak water in the driver's floor board and you hear it splashing in the compartment. We have had it reparied two times. And it works for awhile and then ret

You most likely have a leak in the heater core.
It will have to be removed , repaired or replaced.

Any independent garage can handle the job.

Jun 02, 2014 | 2004 Mitsubishi Endeavor

1 Answer

How do i replace rear wheel bearings

Remove tire, brake caliper, rotor, and abs sensor. Remove complete steering knuckle with hub, rotor sensor, splash shield, and bearing with seals from tie rod, strut, and ball joint. Take complete steering knuckle with hub, rotor sensor, splash shield, and bearing with seals to auto machine shop to have old bearing and seals, and rotor sensor with hub pressed out and new bearing and seals, and rotor sensor with hub pressed in. Don't forget the splash shield that fits between the the steering knuckle and rotor sensor with hub. Reassemble in reverse order. Pay special attention to abs wheel speed sensor specifications. Any further help:

Mar 16, 2013 | 1994 Mitsubishi 3000GT

1 Answer

I'm trying to remove the pivot bolt on the bottom of the alternator from a 1999 mitsubishi galant.

The bolt head hits a plastic splash plate that is fastened to the fender with three bolts . Remove the bolts with a 1/4 inch drive 10mm socket and viola!

Dec 29, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

Air conditioning evapator drain from under dash where is drain hose come out of?

look for a hose hanging down underneath the car floor board ,most likely plugged up at the opening of the drain hose. From road splash. Use a coat hanger wire to open the drain hose!

Sep 10, 2010 | 2005 Mitsubishi Endeavor

1 Answer

How to get to belt there is little space

The belt should be able to be twisted in a manner that will fit into the space between the pulleys and the wheel well. You will also need to remove the tire and the plastic splash guards on the inner wheel well. Romove the plastic grommets carefully. You will now have better access the align the belt onto the pulleys. You will also be able to see theadjuster pulley wilth a square shaped recess that accomadates a breaker bar end or ratchet end. You will beed to turn this pulley while slipping on the belt. Its easier with 2 people. Check the mitsubishi forums for more help.

Aug 06, 2010 | 2003 Mitsubishi Outlander

1 Answer

Change a crankshaft position sensor on a 2000 eclipse

Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Oil capacity?

With the filter this motor is right @ 4.5 quart. In practice most will put in the full 5 quarts with no issues. The extra .5 quart will not cause the crank to splash in the oil.
I hope the may have assisted,

Oct 23, 2009 | 1993 Mitsubishi Galant

1 Answer

Where is the drain plug located on the 2002 Lancer?

Probably under the splash shield, it's an off-white colored plug, but you can remove the lower radiator hose to drain the coolant as well.

Jul 05, 2009 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8832 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides