Question about Ford Cars & Trucks

1 Answer

Have water leaking from the side of engine of ford laser 1999 auto seems like it's coming from the mounting bolt

Left side

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 2,430 Answers

Has to be from the engine block or head welch plugs or perhaps a heater hose , the plugs often rust out replace them with brass plugs.

Posted on May 03, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a coolant leak on a 97 sunfire 2.4l engine.when looking at the engine,is the water pump on the left side or to the right of the engine.


the water pump is in the back of the engine. if you stand at the passengers side fender and look at the motor it is on your left side next to the fire wall,and it is run by the timing chain

Nov 16, 2012 | 1999 Pontiac Sunfire

1 Answer

What is the torque setting for 1999 ford 182 exaust manifold


Check this for 1996-1999 FORD 3.0L (182) V6 DOHC...
- Install the exhaust manifold with a new exhaust manifold gasket.
- Install the exhaust manifold retaining studs and tighten to 13-16 ft. lbs. (18-22 Nm) in the sequence illustrated.
Raise and safely support the vehicle.
Position the Y-pipe assembly using a new flange gasket and install all the retaining nuts and bolts loosely.
Starting at the front of the system tighten the Y-pipe to exhaust manifold nuts to 26-34 ft. lbs. (34-46 Nm).

- Tighten the converter to transaxle nut and bolt to 30 ft. lbs. (40.3 Nm). Tighten the converter outlet bolts to 26-34 ft. lbs. (34-46 Nm).

zjlimited_1988.jpg

Fig. Right side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click image for zoom)


zjlimited_1989.jpg

Fig. Left side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click over image for zoom)

Hope this helps (remember to rating this answer).

Oct 06, 2011 | 1999 Ford Taurus

1 Answer

Were changing the water pump on a 1993 buick lesabre but have run into a problem. Can't get the motor mount out so we can get to the water pump. Have removed 2 bolts and a nut on the engine and all the...


Water Pump REMOVAL & INSTALLATION CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old. 1987-95 Vehicles EXCEPT 1995 VIN 1 ENGINE
  1. Disconnect the negative battery cable.
  2. Drain cooling system into a suitable container.
  3. Remove the serpentine drive belt, as outlined in Section 1 of this manual. NOTE: On some engines, removing the alternator provides better clearance for removing the water pump. For alternator removal and installation procedures, please refer to Section 2 of this manual. Fig. 1: After removing the alternator, remove the brace 89633p01.jpg

  4. Unfasten the water pump pulley bolts, (long bolt removed through access hole provided in the body side rail), then remove the pulley. Fig. 2: Pull the water pump pulley from the pump 89633p03.jpg

  5. Disconnect the radiator and heater hoses from water pump. Fig. 3: Use a screwdriver to loosen the hose clamp screws, then disconnect the hoses from the water pump 89633p02.jpg

  6. For 1992-95 vehicles, remove the torque axis mount, as follows:
    1. Use a suitable engine support fixture and lifting bracket to raise the engine slightly to take the weight off of the engine mounts.
    2. Remove the through-bolt from the torque axis (front) engine mount.
    3. Lift the engine with the support fixture until the power steering reservoir touches the strut tower cross brace.
    4. Loosen the bottom two bolts on the torque axis (front) engine mount.
    5. Remove the A/C line clip and top two bolts on the torque axis engine mount, then remove the mount.
    6. Remove the 2 bolts and nut attaching the engine torque axis mount bracket assembly to the front of the engine. NOTE: On some engines, when you remove the 13mm bolts, coolant will flow from the bolt holes, so make sure to position a drain pan under the pump before unfastening the bolts.
  7. Remove the water pump attaching bolts, then remove the water pump from the vehicle. Remove and discard the gasket. Thoroughly clean the gasket mating surfaces. Fig. 4: Unfasten the water pump mounting bolts (see arrows for locations of top bolts) . . . 89633p04.jpg
    Fig. 5: . . . then remove the water pump from the engine 89633p05.jpg
    Fig. 6: Use a gasket scraper to carefully clean the water pump's mating surface 89633p06.jpg
    Fig. 7: You can also use Scotchbrite® or equivalent non-abrasive scouring pad to clean the water pump gasket mating surface 89633p07.jpg
    Fig. 8: When using a scraper to clean the gasket mating surfaces, be careful not to gouge the engine and cause leaks 89633p10.jpg
    Fig. 9: Exploded view of the water pump mounting - 1994 vehicle shown, others similar 89633g37.gif
    To install:
  8. Apply a suitable sealant to the bolt threads. Fig. 10: Coat the bolt threads with a suitable sealing compound 89633p09.jpg

  9. Position a new gasket, then install the water pump to the engine and tighten the retaining bolts, as follows: Fig. 11: Place a new gasket on the water pump mounting surface 89633p08.jpg
    1. For 1987-94 vehicles, tighten the long bolts to 29 ft. lbs. (39 Nm) and the short bolts to 97 inch lbs. (11 Nm).
    2. For 1995 vehicles, tighten the water pump-to-block bolts to 22 ft. lbs. (30 Nm) and the water pump-to-front cover bolts to 11 ft. lbs. (15 Nm), plus an additional 80°rotation.
  10. For 1992-95 vehicles, install the torque axis mount, as follows:
    1. Attach the torque axis engine mount bracket assembly to the front of the engine using the 2 bolts and nut. Fig. 12: Install the torque axis engine mount bracket and secure with the 2 bolts and nut 89633g34.gif

    2. Replace the 2 upper bolts previously removed from the torque axis engine mount, and attach the mount and plastic clip for the A/C lines.
    3. Tighten the 2 lower bolts that were previously loosened on the torque axis engine mount. Fig. 13: Exploded view of the torque axis engine mount and tightening specifications 89633g35.gif

    4. Adjust the engine height to align the torque mount with the torque axis mount bracket.
    5. Insert the through-bolt, attach the retaining nut and tighten to the specifications shown in the accompanying figure. Remove the engine support and lifting fixture. Fig. 14: Insert the torque axis mount bracket through-bolt 89633g36.gif

  11. Install the water pump pulley and secure with the retaining bolts.
  12. Connect the radiator and heater hoses to the water pump.
  13. Install the serpentine drive belt.
  14. Connect the negative battery cable.
  15. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Check for leaks and top-off the coolant.

Dec 17, 2010 | Buick LeSabre Cars & Trucks

1 Answer

Water pump removal


Water Pump REMOVAL & INSTALLATION CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old. 1.8L Engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the timing belt.
  4. Raise and safely support the vehicle.
  5. Remove the engine oil dipstick tube bracket bolt(s) from the water pump.
  6. Remove the two bolts and the gasket from the water inlet pipe.
  7. Remove all but the uppermost water pump mounting bolt.
  8. Lower the vehicle.
  9. Remove the remaining bolts and the water pump assembly.
  10. If the water pump is being reused, remove all gasket material from the water pump.
  11. Remove all gasket material from the engine block. Fig. 1: Exploded view of a water pump mounting - 1.8L engine 86753048.gif
    To install:
  12. Install a new gasket onto the water pump.
  13. Place the water pump into its mounting position, then install the uppermost bolt.
  14. Raise and safely support the vehicle.
  15. Install the remaining water pump mounting bolts and tighten all bolts to 14-19 ft. lbs. (19-25 Nm).
  16. Install a new gasket onto the water inlet pipe.
  17. Install the two bolts from the water inlet pipe to the water pump and tighten to 14-19 ft. lbs. (19-25 Nm).
  18. Install the bolt to the engine oil dipstick tube bracket.
  19. Lower the vehicle.
  20. Install the timing belt.
  21. Fill the cooling system.
  22. Connect the negative battery cable.
  23. Start the engine and allow it to reach operating temperature. Check for coolant leaks.
  24. Check the coolant level and add coolant, as necessary.
1.9L Engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the timing belt cover and the timing belt.
  4. Raise and safely support the vehicle.
  5. Remove the lower radiator hose from the water pump.
  6. Remove the heater hose from the water pump.
  7. Lower the vehicle.
  8. Support the engine with a suitable hydraulic floor jack.
  9. Remove the right engine mount attaching bolts and roll the engine mount aside.
  10. Remove the water pump attaching bolts.
  11. Using the floor jack, raise the engine enough to provide clearance for removing the water pump.
  12. Remove the water pump and gasket from the engine through the top of the engine compartment. Fig. 2: Disconnect the lower radiator hose (A) from the water pump (B) 90983p45.jpg
    Fig. 3: Disconnect the heater hose (A) from the water pump (B) 90983p46.jpg
    Fig. 4: Remove the water pump's lower mounting bolts (arrows) . . . 90983p47.jpg
    Fig. 5: . . . and the upper mounting bolts 90983p44.jpg
    Fig. 6: After raising the engine enough to provide clearance, remove the pump from the engine compartment 90983p49.jpg
    Fig. 7: Use a scraper to clean the mating surfaces of the cylinder block and water pump 90983p50.jpg
    To install:
  13. Make sure the mating surfaces of the cylinder block and water pump are clean and free of gasket material.
  14. If the water pump is to be replaced, transfer the timing belt tensioner components to the new water pump.
  15. With the engine supported and raised with a suitable floor jack, place the water pump and the gasket on the cylinder block and install the four attaching bolts. Tighten the bolts to 15-22 ft. lbs. (20-30 Nm).
  16. Install the timing belt and cover.
  17. Roll the engine mount into position and install the mount bolts. Remove the floor jack.
  18. Raise and safely support the vehicle.
  19. Connect the heater hose to the pump.
  20. Lower the vehicle.
  21. Connect the negative battery cable.
  22. Refill the cooling system.
  23. Start the engine, allow it to reach normal operating temperature and check for coolant leaks.
  24. Check the coolant level and add as necessary.
prev.gif next.gif

Nov 08, 2010 | 1999 Ford Escort

1 Answer

How do i replace a water pump on a 1992 buick lesabre custom


GM Bonneville/Eighty Eight/LeSabre 1986-1999 Water Pump - REMOVAL & INSTALLATION

CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
1987-95 Vehicles
EXCEPT 1995 VIN 1 ENGINE
  1. Disconnect the negative battery cable.
  2. Drain cooling system into a suitable container.
  3. Remove the serpentine drive belt, as outlined in of this repair guide.
On some engines, removing the alternator provides better clearance for removing the water pump. For alternator removal and installation procedures, please refer toin this repair guide.

  1. Unfasten the water pump pulley bolts, (long bolt removed through access hole provided in the body side rail), then remove the pulley.
  1. Disconnect the radiator and heater hoses from water pump.
  1. For 1992-95 vehicles, remove the torque axis mount, as follows:
    1. Use a suitable engine support fixture and lifting bracket to raise the engine slightly to take the weight off of the engine mounts.
    2. Remove the through-bolt from the torque axis (front) engine mount.
    3. Lift the engine with the support fixture until the power steering reservoir touches the strut tower cross brace.
    4. Loosen the bottom two bolts on the torque axis (front) engine mount.
    5. Remove the A/C line clip and top two bolts on the torque axis engine mount, then remove the mount.
    6. Remove the 2 bolts and nut attaching the engine torque axis mount bracket assembly to the front of the engine.

On some engines, when you remove the 13mm bolts, coolant will flow from the bolt holes, so make sure to position a drain pan under the pump before unfastening the bolts.
  1. Remove the water pump attaching bolts, then remove the water pump from the vehicle. Remove and discard the gasket. Thoroughly clean the gasket mating surfaces.
To install:
  1. Apply a suitable sealant to the bolt threads.
  1. Position a new gasket, then install the water pump to the engine and tighten the retaining bolts, as follows:
  1. For 1987-94 vehicles, tighten the long bolts to 29 ft. lbs. (17 Nm) and the short bolts to 97 inch lbs. (11 Nm).
  2. For 1995 vehicles, tighten the water pump-to-block bolts to 22 ft. lbs. (30 Nm) and the water pump-to-front cover bolts to 11 ft. lbs. (15 Nm), plus an additional 80° rotation.

  1. For 1992-95 vehicles, install the torque axis mount, as follows:
    1. Attach the torque axis engine mount bracket assembly to the front of the engine using the 2 bolts and nut.
    2. Replace the 2 upper bolts previously removed from the torque axis engine mount, and attach the mount and plastic clip for the A/C lines.
    3. Tighten the 2 lower bolts that were previously loosened on the torque axis engine mount.
    4. Adjust the engine height to align the torque mount with the torque axis mount bracket.
    5. Insert the through-bolt, attach the retaining nut and tighten to the specifications shown in the accompanying figure. Remove the engine support and lifting fixture.
  2. Install the water pump pulley and secure with the retaining bolts.
  3. Connect the radiator and heater hoses to the water pump.
  4. Install the serpentine drive belt.
  5. Connect the negative battery cable.
  6. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Check for leaks and top-off the coolant.

Hope this help (remember comment and rated this; TY for using Fixya.

Mar 31, 2010 | 1992 Buick LeSabre

2 Answers

Where is water pump located on 1997 nissan pick up truck


Several engines in here:

- 2.0L
b8ce1b5.jpg

View of the water pump mounting and O-ring-2.0L engine


- 2.4 L
81bf5ba.jpg

Exploded view of the water pump and mounting on the engine-2.4L engine


- 2.5L
21fb20c.jpg

View of the water pump mounting-2.5L engine


For remove in a 2.0L
  1. Disconnect the negative battery cable.
  2. Properly drain the engine coolant into a clean container for reuse.
  3. Remove the timing belt.
  4. Unfasten and remove the timing belt rear protective covers.
  5. Detach the hose from the water pump.
  6. Unfasten the water pump attaching bolts, then remove the water pump and seal ring.
To install:
  1. Thoroughly clean and dry the mounting surfaces, bolts and bolt holes.
  2. Using a new sealing ring, install the water pump to the engine and hand-tighten the retaining bolts.
  3. Attach the hose to the water pump.
  4. Fasten the timing belt rear protective covers, then install the timing belt and properly adjust the tension.
  5. Tighten the water pump bolts to 18 ft. lbs. (24 Nm).
  6. Install the timing belt cover and related parts.
  7. Connect the negative battery cable.
  8. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Recheck for leaks and top-off the coolant.

For more details about other engines, can visit autozone.com

Hope helped. Good luck.

Nov 02, 2009 | 1997 Nissan Pickup

1 Answer

Removal and installation of an auto trans in 2002 toyota camry


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the transaxle fluid.
  3. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Battery Air cleaner assembly Throttle cable from the throttle body Cruise control actuator cover and connector, if equipped Ground wire Starter Speed sensor connectors, direct clutch speed sensor, and the park/neutral position switch connector on the transaxle Solenoid connector on the transaxle Shift control cable Oil cooler hoses Front side transaxle mounting bolts Front engine mounting bolts Oil cooler line mounting bolts from the front frame Upper transaxle to engine mounting bolts

    0900c15280197a59.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tie the steering rack to the engine support fixture components, as shown-Avalon and Camry
    Front exhaust pipe Engine side covers and undercovers Both halfshafts Front side engine mounting nut Rear side engine mounting bolts (remove hole plugs) Left side transaxle mounting bolts Steering gear housing Front frame assembly Rear end plate mounting bolts Torque converter cover Torque converter retaining bolts Remaining transaxle mounting bolts Transaxle

Apr 09, 2009 | 2002 Toyota Camry

1 Answer

Water pump


Okay...this is how to remove and install it....you do it from under neath...some of it...

DOHC ENGINE
  1. Disconnect the negative battery cable. CAUTION
    Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  2. Drain and recycle the engine coolant.
  3. Raise the car and support it with safety stands.
  4. Unfasten the splash shield bolts and remove the shield.
  5. Loosen the water pump pulley retaining bolts, then remove the drive belt.
  6. Remove the A/C compressor bolts and move the compressor aside.
  7. Unfasten the water pump retainers and remove the pump from the middle timing belt cover.
  8. To install:
  9. Install the water pump and tighten the retainers to 17 ft. lbs. (24 Nm).
  10. Place the A/C compressor in position and tighten the mounting bolts.
  11. Install the drive belt and tighten the water pump pulley bolts.
  12. Install the splash shield and tighten the bolts.
  13. Fill the cooling system with the proper amount and mixture of coolant.
  14. Connect the negative battery cable.
  15. Start the engine and check for leaks.

Apr 05, 2009 | 2006 Ford Laser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...