Question about Ford Cars & Trucks

1 Answer

What upper and lower radiator hoses will fit a 1978 ford f100 with a 351W engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,051 Answers

Go on line to auto zone and put in the make, model and year of the truck and it will give you a number for replacement of the hoses.

Posted on May 03, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Waterpump 2002 ford turaus 3.0 durtec


3.0L Engine

VIN S Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
  • Splash shield
  • Lower heater hose
  • Radiator lower tube bolt
  • Radiator upper front tube bolt
  • Air cleaner assembly
  • Battery and tray
  • Water pump belt
  • Upper radiator hose
  • Engine vent hose
  • Transaxle 10 pin connector
  • Radiator bypass hose assembly
  • Thermostat housing
  • A/C compressor brace, if equipped
  • Water pump mounting nuts
  • Connector hose
  • Water pump




25996402-nto4xxgg4h3g52i5qee3bm1e-1-0.gif
To install:
  1. Install or connect the following:
  • Water pump
  • Connector hose
  • Water pump mounting nuts and tighten them to 15-22 ft. lbs. (20-30 Nm)
  • A/C compressor brace, if equipped, and tighten the nuts to 15-22 ft. lbs. (20-30 Nm)
  • Thermostat housing
  • Radiator bypass hose assembly
  • Transaxle 10 pin connector
  • Engine vent hose
  • Upper radiator hose
  • Water pump belt
  • Battery and tray
  • Air cleaner assembly
  • Radiator upper front tube bolt
  • Radiator lower tube bolt
  • Lower heater hose
  • Splash shield
2. Fill the cooling system.
3. Start the engine and check for leaks.

Dec 06, 2015 | 2002 Ford Taurus

1 Answer

How do i replace the radiator on a 2003 Buick Lesabre


3.8L Engine

  1. Drain the engine coolant.
  2. Remove the upper radiator seal.
  3. Remove the upper tie bar.
  4. Disconnect the coolant overflow hose from the radiator.
  5. Plug the coolant overflow hose.
  6. Disconnect the upper and lower radiator hoses.
  7. Remove the transaxle oil cooler pipe bracket bolt from the lower tie bar.
  8. Remove the cooling fans.
  9. Slide the plastic cap off the transaxle oil cooler pipe quick connect fittings.
  10. Disconnect the upper and lower transaxle oil cooler pipes from the radiator.
  11. Remove the A/C condenser mounting bolts.
  12. Separate the condenser from the radiator.
  13. Lift the radiator up and out of the vehicle.
To install:
  1. Install the radiator to the vehicle. Place the bottom of the radiator in the lower pads.
  2. Install the condenser to the radiator.
  3. Install the A/C condenser mounting bolts and tighten to 115 inch lbs. (13 Nm).
  4. Push the upper and lower transaxle oil cooler pipes into the radiator quick connect fittings, until a "click" is heard.
  5. Tug gently on the cooler pipes to ensure proper retention.
  6. Slide the plastic caps (1) over the quick connect joints.
  7. Install the cooling fans.
  8. Install the transaxle oil cooler pipe bracket bolt to the lower tie bar and tighten to 89 inch lbs. (10 Nm).
  9. Install the upper and lower radiator hoses.
  10. Connect the coolant recovery hose to the radiator neck.
  11. Install the upper tie bar.
  12. Install the upper radiator seal.
  13. Fill the cooling system.
  14. Inspect the transmission oil level.

Nov 02, 2015 | Buick Cars & Trucks

1 Answer

Steps on removing and replacing radiator on my 1999 jeep cherokee sport 6 cyl. stright


Things You'll Need
  • Waste oil collection pan
  • Needle nose pliers
  • Phillips head screwdriver
  • Wrench set
  • Socket set
  • Antifreeze
  • Water
armor-all-tyn2.png
  1. Draining the Cooling System
    • 1 Locate the petcock valve on the lower right corner of the radiator and place a waste oil collection pan underneath it.
    • 2 Open the petcock valve by turning it counterclockwise, using needle nose pliers.
    • 3 Wait until all the coolant has drained out then close the petcock valve by turning it clockwise.
    Removing the Radiator
    • 1 Loosen the hose clamp that connects the upper radiator hose to the radiator using a Phillips head screwdriver. Then pull the upper radiator hose off the radiator.
    • 2 Loosen the hose clamp that connects the lower radiator hose to the radiator using a Phillips head screwdriver. Then pull the hose off the radiator.
    • 3 Unscrew the transmission cooler lines from the radiator (automatic transmission only) using a wrench.
    • 4 Unscrew the bolts that secure the radiator to the core support, using a socket.
    • 5 Lift the radiator straight up to remove it from the vehicle.
    Installing the Radiator
    • 1 Lower the radiator into position behind the core support. Be careful: the cooling fins are thin and can be easily damaged.
    • 2 Screw the bolts that secure the radiator into the core support. Tighten with a socket.
    • 3 Thread the transmission cooler line fittings into the radiator. Tighten with a wrench.
    • 4 Slide the lower radiator hose onto the fitting on the bottom of the radiator. Slide the hose clamp over the fitting and tighten with a Phillips head screwdriver.
    • 5 Slide the upper radiator hose onto the fitting on the top of the radiator. Slide the hose clamp over the fitting and tighten with a Phillips head screwdriver.
    • 6 Fill the engine with a 50/50 mix of antifreeze and water.
    • 7 Run the engine and visually inspect for leaks.

Aug 30, 2011 | 1999 Jeep Cherokee 4WD

1 Answer

How do I remove my car radiator?


Section 303-03: Cooling, Engine 1997 Explorer, Mountaineer Workshop Manual REMOVAL AND INSTALLATION Radiator - 4.0L Removal
  1. NOTE: Refer to following illustrations.
    Drain the cooling system by removing the radiator cap (8100) and attaching a 9.5 mm (3/8 inch) inside diameter hose to the draincock nipple, located at the lower rear corner of the radiator tank. Then, open the radiator draincock (8115) and allow the coolant to flow through the hose into a suitable container.
  1. Loosen hose clamps at throttle body and engine air cleaner assembly. Remove air cleaner outlet tube and position aside.
  1. Remove radiator overflow hose from the radiator, disconnect two hose locators at top of radiator and position hose aside.
  1. Remove two fans shroud bolts. Lift the fan shroud out of the lower retaining clips and position it on the fan blade.
  1. Position upper and lower radiator hose clamps, remove hose from radiator and position it on the fan blade.
  1. Disconnect the two transmission cooling lines from the oil cooler fittings on the radiator, install protective caps over lines and position aside.
  1. Remove two upper radiator bolts.
  1. Tilt the radiator back (rearward) approximately 25 mm (one inch) and lift directly upward, clear of the radiator support bracket and the fan blade.
Installation
  1. Position the radiator into engine compartments, make sure that mountings on both tanks are inserted into radiator support brackets. Install radiator retaining bolts. Tighten to 6-8 - (54-70 lb-in).
  1. Remove protective caps from cooler lines. Connect the two transmission cooling lines at the oil cooler fittings on radiator. Tighten to 16-24 - (12-17 lb-ft).
  1. Install upper radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Install lower radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Position fan shroud in lower retaining clips and install upper bolts. Torque to 6-8 - (54-70 lb-in).
  1. Position radiator overflow hose, connect to radiator and locators.
  1. Position air cleaner outlet tube to throttle body and air cleaner assembly. Tighten to 2-3 - (18-27 lb-in).
  1. Fill the cooling system; refer to Cooling System Draining, Filling and Bleeding in this section.

Oct 28, 2010 | 1997 Mercury Mountaineer

2 Answers

How to remove radiator from my 2000 chrysler 300


Radiator Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect negative cable.
  3. Drain cooling system.
  4. Remove or disconnect the following:
    • Radiator upper crossmember
    • Upper and lower coolant hoses from the radiator
    • Transmission hoses from cooler
    • Engine oil cooler lines (if equipped)
    • Radiator fan electrical connector and fan assembly
    • Condenser mounting screws located at the front of the radiator
    • Transmission cooler line bracket from left side of radiator
  5. Lift condenser upward enough to disengage upper mounting clips. Allow condenser to rest on lower radiator crossmember.
  6. Lifted radiator from engine compartment.
To Install:
  1. Seat the radiator assembly lower rubber isolators into the mounting holes in radiator lower support.
  2. Attach air conditioning condenser to radiator
    • Torque to 45 inch lbs. (5 Nm)
  3. Install or connect the following:
    • Radiator lower hose
    • Transmission cooler line bracket and transmission hoses
      1. Torque to 28 inch lbs. (3 Nm)
    • Radiator fan and electrical connector
    • Engine oil cooler lines (if equipped)
      1. Torque to 160 inch lbs. (18 Nm)
    • Radiator upper hose
    • Radiator upper support crossmember
    • Negative cable
  4. Fill cooling system with coolant.
prev.gif next.gif

Aug 03, 2010 | 1999 Chrysler 300M

2 Answers

How to change radiator in 1992 ford explorer


Radiator Removal
  1. Drain the cooling system by removing the radiator cap and attaching a 9.5mm (3/8-inch) inside diameter hose to the draincock nipple, located at the lower rear corner of the radiator tank. Then, open the draincock and allow the coolant to flow through the hose into a suitable container.
  1. Remove the rubber overflow tube from the radiator and store it out of the way.
  1. Remove the shroud's or finger guard's two upper attaching screws. Lift the shroud out of the lower retaining clips and drape it on the fan.
  1. Loosen upper and lower hose clamps at the radiator and remove hoses from the radiator connectors.
  1. For vehicles with automatic transmissions:
    1. Disconnect the two transmission cooling lines from the oil cooler fittings on the radiator. Intermediate flare fittings as shown remain as originally installed.
    1. Disconnect the transmission cooler tube support bracket from the bottom flange of the radiator by removing the screw.

  1. Remove the two radiator upper attaching screws.
  1. Tilt the radiator back (rearward) approximately 25mm (one inch) and lift directly upward, clear of the radiator support and the cooling fan.
  1. If either hose is to be replaced, loosen clamp at the engine end and slip the hose off the connections with a twisting motion.
  1. Lift the shroud off the fan and remove from the vehicle.
  1. Remove the radiator lower support rubber insulators.


8a0d173.gif

Jun 12, 2010 | Ford Explorer Cars & Trucks

1 Answer

How to remove and replace radiator on 1998 ford taurus


  1. Disconnect battery ground cable.
  2. Remove the battery.
  3. Remove clip retaining constant control relay module and position module aside.
  4. Remove battery tray.
  5. Remove radiator cap.
  6. Raise vehicle on hoist.
  7. Remove radiator splash shield.
  8. Drain engine cooling system.
  9. Remove radiator mounting bracket assembly.
  10. Remove lower radiator hose.
  11. Partially lower vehicle.
  12. Remove upper radiator hose.
  13. Remove radiator overflow hose.
  14. Remove upper A/C condenser core retaining bolts.
  15. Remove upper A/C transmission oil cooler tube clips.
  16. Remove upper transmission oil cooler tube (7C410) using 3-8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  17. Raise vehicle on hoist.
  18. Remove lower transmission oil cooler tube clips.
  19. Remove lower transmission oil cooler tube using 3/8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  20. Remove transmission oil cooler bracket and position transmission oil cooler aside.
  21. Remove lower A/C condenser core bolts and position A/C condenser core (19712) aside.
  22. Remove radiator support bracket.
  23. Remove radiator.

May 07, 2010 | 1998 Ford Taurus

1 Answer

What is the procedure for removal of the radiator from the Mercury Mystique(1998 model)?


Ford Contour/Mystique/Cougar 1995-1999 Repair Guide

Radiator -REMOVAL & INSTALLATION
(see Figures 1 through 7)

7249321.jpg
Fig. 1: Remove the upper radiator hose from the radiator


d2d2436.jpg
Fig. 2: Use a back-up wrench to remove the transaxle cooler line connections-automatic transaxle only


3213ac8.jpg
Fig. 3: the lower transaxle cooler line connection


ec9272d.jpg
Fig. 4: Remove the passenger side radiator mount and ...


956cd3d.jpg
Fig. 5: ... and the driver's side radiator mount


f06fec0.jpg
Fig. 6: The condenser can be support using mechanic's wire as shown here, or another suitable device


242d821.jpg
Fig. 7: Carefully lower the radiator out the bottom of the vehicle
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Remove the upper radiator hose from the radiator.
  4. On 2.5L equipped vehicles, remove the radiator overflow hose from the radiator.
  5. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler inlet fitting and plug the line and the fitting.
  6. Remove the engine fan.
  7. Raise and support the vehicle.
  8. Remove the lower radiator hose from the radiator.
  9. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler outlet fitting and plug the line and the fitting.
Remove the cooler lines while holding the radiator connector with a back-up wrench.
  1. Support the radiator, and A/C condenser with a jackstand or other suitable device.
  2. Remove the lower radiator supports from the front of the subframe.
  3. Remove the two retaining bolts for the A/C condenser from the brackets at the bottom of the radiator.
  4. Position the jackstand aside and remove the radiator out the bottom of the vehicle.
To install:
  1. Carefully raise the radiator into place and support the radiator with a jackstand or other suitable device. Install the two retaining bolts for the A/C condenser into the brackets at the bottom of the radiator.
  2. Install the lower radiator supports and tighten the bolts to 71-97 inch lbs. (8-11 Nm).
  3. Remove the jackstand and install the transmission cooler outlet line (if equipped) and the lower radiator hose to the radiator.
  4. Lower the vehicle.
  5. Install and tighten the fan shroud nuts.
  6. Install the transmission cooler inlet line (if equipped) and the upper radiator hose to the radiator.
  7. On 2.5L equipped vehicles, install the radiator overflow hose from the radiator.
  8. Connect the negative battery cable.
  9. Fill the cooling system with the proper 50 / 50 mixture and start the vehicle.
  10. Bleed the cooling system and check for leaks.

Hope helps with this (remember rated this help) Good luck.

Jan 20, 2010 | 1996 Mercury Mystique

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    87 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    77169 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    fordexpert

    Level 3 Expert

    5575 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...