Question about Cars & Trucks

Open Question

I have a L39 and it will not go into gear. it has an GST error code 60

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Rosa bus, model PA-BE64DJ automatic transmission. Where can I get gear selector switch?


PDF]TRANSMISSION Workshop Manual FR M/T (W-E)

www.mitsubishi-motors.kiev.ua/Manuals/Transmission/.../22D.pdf
Transmission Model. Gear ratio. Speedometer gear ratio. Vehicle Model. EngineModel. EUR ... 0.856. Reverse. 4.142. 3.578. V5M21 TRANSMISSION MODEL. Gearratio. A. B. C. 1st. 4.330. 3.967 ... Transmission. Backup lamp switch. 29 ± 2.

[PDF]BONLUCK BUS & COACH - Australasian Bus and Coach

www.busnews.com.au/media/.../abc_310_p72-73_classifieds-1-.pdf
LUGGAGE BINS RADIO,CD,P.A.. DISC BRAKES ... THE BUS YOU WANT IS NOW EASIER TO FIND ... 2006 MITSUBISHI ROSA DELUXE AUTO ... 25 Seater, 4 Cyl Turbo Diesel Automatic Transmission, Highback ... 2009 MODEL $120,000 + $12,000 GST = $132,000 ..... 50 seater, engine-gear box rebuild - only 130 000km.Missing: be64dj ‎selector ‎switch

Dec 18, 2015 | Mitsubishi Cars & Trucks

1 Answer

I have a 1995 eclipse gst turbo 5 speed, theobd2 is p0120 i wonder if the pcm is bad? it goes in and out when the rpms reach 4,500 so i gotta shift early, it does it sometime and sonmetimes it doesnt. i...


Make sure the throttle body is clean (scrub brush and cleaner)but don't scratch it. If you only have trouble at high rpm it may be the computer limiting engine damage. You may have to clean the idle air port or check its operation to clear the error code.

Mar 09, 2014 | Mitsubishi Eclipse Cars & Trucks

1 Answer

1997 eclipse spider gst automatic trans slipping out of gear while driving, in over drive.


Have the fault codes read Replace the faulty units with genuine one because most aftermarket units are not set
for OEM cpu units and are not completely compatible Have a pressure test done on the transmission. Check oil
level on dip stick

May 05, 2013 | Cars & Trucks

2 Answers

Vehicle hesitates while accelerating and doesn't go over 60


try adding heavy gage ground wire(s) to fire wall, starter bolts anywhere that looks like thick steel.

May 06, 2012 | 2000 Toyota MR2 Spyder

2 Answers

Code po734, po735


This is what your codes mean:

Trouble Code-P0734 (A/T Additional Gear Ratio Error In Fourth Gear)


Trouble Code Conditions:
Vehicle driven to a speed of 4-37 mph at more than 500 rpm, gear selector in 4th Gear in Drive, and the PCM detected too much difference in the engine speed and output shaft speed.

Possible Causes:

  • Customer may complain of intermittent 4th gear operation
  • O/D and 2/4 pressures less than 75 psi
  • O/D or 2/4 clutch volume indexes out of specification
  • O/D accumulator seals are damaged
  • Transmission enters "limp in" mode running in 4th gear

Trouble Code-P0735 (A/T Gear Ratio Error Fourth Prime)

Trouble Code Conditions:
Vehicle driven any forward Gear, and the TCM detected the ratio of the Input speed to the Output Speed did not match the current Gear Ratio (this test can take up to 5 minutes).

Possible Causes:

  • Related Gear Ratio trouble codes may be stored (note that some of these Gear Ratio trouble codes may be intermittent)
  • Transmission has internal problems or damage present
You have a transmission problem.

Jan 17, 2011 | 2003 Dodge Durango

1 Answer

WHATS THE CODE TO THE FACTORY RADIOS ON A 1997 ECLIPSE GST TURBO


your best bet is taking the details of the car like vin/chassis number to your nearest dealer, most codes like key, ignition, radio code, etc are stored in their system databases.

Jun 21, 2010 | 1997 Mitsubishi Eclipse

1 Answer

Gear box problem


96 intrepid lost 3rd and4th gears will only run in 1st and 2nd
no lights or other warnings .car was in cruise at 60 when engine
just went flat out trying to keep to 60 no codes showing any faults

May 19, 2010 | 1996 Dodge Intrepid

1 Answer

Timing my 1998 Mitsubishi Eclipse GST


the timing marks on your crank and cam crank need to be one on top of the other if you understand what i mean. anyway if this is done correctly, your cam should make two revolutions to one of the crank thus after one full revolution of the crankshat gear your camshaft gear should do 2 revolutions and you timing marks should be next to one another

Jan 08, 2009 | 1998 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...