Question about Oldsmobile Cars & Trucks

Open Question

1988 oldsmobile intrepid fuel pump wiring

No fuel pressure in line

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 625 Answers

SOURCE: 1999 oldsmobile alero

check the fuel pump fuse, and if ok look foe fuel pump relay and replace it

Posted on Jun 02, 2008

Ad
  • 1 Answer

SOURCE: Location of fuel line and fuel pump on a 1988 Subaru Justy

I imagine you have found it by now but just in case, the fuel pump and filter are mounted on the underside of the frame just ahead of the left rear suspension.

Posted on Jul 05, 2008

short shadey
  • 421 Answers

SOURCE: 1988 jeep wrangler no fuel

check your fuel pump relay and your ignition switch those numbers you gave for voltage are not right, please recheck that you have a ground and 12volts at the pump while cranking please rate -jeff

Posted on Sep 04, 2008

michigan man
  • 3533 Answers

SOURCE: fuel line diagram

try an autozone or a dealership they can print out the diagrams for you

Posted on Feb 03, 2009

mcgyver468
  • 710 Answers

SOURCE: ran yesturday, tried today no fuel in lines, or pressure in rail, fuel pump not activating

Check the fuel pump fuse and relay under the hood in the fuse panel. If both fuse and relay are good then fuel pump may be at fault, but it seems too new for a fuel pump replacement. Hope this helps. Keep me posted please. Good luck

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i test a fuel pump relay on a 1997 dodge intrepid


there should be a spot either on the fuel rail or fuel line where you can unscrew a cap and screw on a gauge so when you turn the key on and the fuel pump kicks on you can see how much pressure its putting out find out what the pressure is supposed to be an see if yours is weak.

Mar 20, 2013 | 1997 Dodge Intrepid

1 Answer

Repacing fuel filter on 1996 intrepid


1) Relieve the fuel system pressure by first removing the fuel pump relay from the Power Distribution Center. Then, start the engine and let it to run until it stalls. Try starting it again and allow it to run until it stalls. Continue restarting the engine until the car will no longer start. Turn off the ignition.
2) Disconnect one electrical connector from an injector. Use an alligator clip to connect an end of a jumper wire to either injector terminal. Connect the other end of the jumper wire to the positive side of the battery. Then, connect an end of a second jumper wire to the other injector terminal. Very briefly touch the other end of the jumper wire to a ground.
3) Locate the fuel filter, which is part of the fuel pressure regulator mounted on the fuel pump module. Disconnect the negative battery cable, then lower the fuel tank. Disconnect the fuel lines from the filter.
4) Remove the fuel line from the pressure regulator. Remove the filter/regulator by pushing in on the locking tab on the filter as you turn the regulator to unlock it. Then, pull it straight up.
5) Push the new fuel filter into the fuel pump module. Turn to lock it in place. Connect the fuel lines, and then you can reinstall the fuel tank. Check for leaks when you start the engine on your Dodge Intrepid.

Parts Of BMW.





May 30, 2012 | 1999 Dodge Intrepid

1 Answer

1997 Dodge Intrepid has set up for several months while in hospital. Will not fire. Put small gas amount in air intake and it fires and runs for 10-15 seconds. Gas probably not getting to injectors. Pump...


Several months could be a tank of bad gas. When turning the ignition to on position the pump runs for 3 to 5 seconds to pressurize the system, next find the valve on fuel rail and press it, Shield with a rag while doing this. You should get fuel. Check the way it smells, bad gas has an awful smell that can make you hurl! Attach a fuel pressure tester, it should be around 50lbs. If it's bad empty the tank by pressing the needle and relieving the pressure. Next disconnect fuel line before the filter get a container to catch the gas. IN the engine conpartment disconnect the fuel pump relay and put a jumper wire to run the pump until tank is drained. Instal new filter and pump if needed and add a can of "Seafoam" to the tank with fresh gas. Run pump until there's fuel at the fuel rail then put relay back in. now we should have ignition and constant running. Hope this helped.

Oct 07, 2010 | 1997 Dodge Intrepid

1 Answer

New fuel filter and fuel pump installed but car still has fuel problems.


Check the fuel pressure regulator and check fuel pressure. Have you tested the fuel pump relay?

Apr 19, 2010 | 1988 Oldsmobile Cutlass Supreme

2 Answers

99 dodge fuel pump intrepid how to change it


Start by safely raising the rear end of the vehicle well above the ground. Note: it is best to change the fuel pump with as little fuel in the tank as possible. Once under the car locate the fuel tank and remove the large filler tube going into the side of the tank. Also, if equipped, remove the smaller tube next to the filler tube. Then, remove the two bolts furthest to the rear of the vehicle that are retaining the fuel tank hanger brakets. This should allow the tank to sag down in the rear end, allowing you access to the fuel pump wiring harness, vent tube, pressure line, and return line. Remove all of these carefully. Note beware of residule fuel pressure in the lines, also the fuel lines may require special disconnect tools to unfasten them from the pump assy. With all lines, tubes, and wiring removed from the tank, remove the brackets from the tank and manuver the tank to the ground. Move it to a well ventailated spot and then use a flat tip screw driver and a hammer to work the fuel pump assy. retainer nut couter clockwise off of the tank. Remove the pump assy. from the tank carefully and replace. Reverse procedure to reinstall. When attempting to start the vehicle the first time after service cycle the ignition key back and forth from the locked to the on position at least three times in order to prime the fuel system, as there is no fuel pressure in the lines following there removal. Also be sure to check closely for leaks once the vehicle is running. Then watch closely when adding fuel for the first time following service to ensure a proper seal at the filler tube.

Oct 24, 2009 | 1999 Dodge Neon

2 Answers

1988 cutlas ciera starts but stalls imediatly has 34 lbs fuel pre


If you have a V-6, your fuel pressure should be 40 to 45 lbs. If you have'nt done it already, replace the fuel filter and try again. Make sure the pressure does not leak down to near 0 lbs, the pump should hold near the pressure it produces.
Good luck, let me know.
Regards,

May 12, 2009 | 1987 Oldsmobile Ciera

2 Answers

How do you changs a fuel pump in a 1995 Dodge


You MIGHT not have to drop the tank. On the 95 LHS (same frame) you can go through the trunk. take the trunk lining out. Underneath it near the back seat there may be an access panel. If so it will make it MUCH easier to replace! Worth the time to check it out!

Apr 12, 2009 | 1997 Dodge Intrepid

2 Answers

Replacing fuel pump on 1995 oldsmobile aurora


The GM 1995 Aurora repair manual, says to use the access hole under the carpet in the back right corner of the trunk. You are best to buy a new fuel sender locking nut or ring at the dealer for about $8.


Forgot to add this - to relieve the fuel pressure, just use the press the center of valve on the fuel rail (for pressure testing) and a rag to catch the dribble. Really no big deal.

Make sure disconnect the battery cables too

Mar 23, 2009 | 1995 Oldsmobile Aurora

1 Answer

Fuel pump fuse night mare


It ended up being a bad oil pressure sending unit, it is in the power loop for the pump. When the oil pressure would come up when started that is when the fuse would blow. A friend who works for a mechanic in town found a diagnosis digram for the fuel pump and that is how we found out that the the oil pressure sending was in the wiring loop for the fuel pump

Dec 12, 2008 | 1988 Oldsmobile Delta 88

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...