Question about Mazda Cars & Trucks

1 Answer

2005 mazda 6 PO753 check engine light on and AT on. did repairs changed soleonid a and checked all electrical.reset code . start the engine no lights come on till i put it in gear then the lights on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 44,411 Answers

Code p 0735 refers to gear 5--incorrect ratio====causes ---wiring---TR sensor /switch---shift solenoid--transmission mechanical fault
replace the TR switch /sensor

Posted on May 03, 2017

  • mckmi8 May 03, 2017

    hi bill you changed the code from 753 to 734 and the trans is auto 4 speed

  • Bill Boyd May 03, 2017

    sorry about that --code p 0753 refers to shift solenoid (SS) A electrical====causes--wiring---shift solenoid---ECM---TCM seeing as to how you have changed the solenoid , I would be checking the TCM ( transmission control module ) for correct operation

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tcs light flashes and p0340 code


P0340 code means "Something" is wrong in the timing...
from CMP (Camshaft Position sensor) to the crankshaft bolt.

Very first thing, verify connectors are clean and shiny.
clear all codes, even hard codes.

57f2e883-ce32-4061-b04b-ae0890f2c653.gif
612c4a6c-208f-43b8-8645-8318e85f9e48.gif
9e0c3051-1208-49b3-95d5-de3ff545fd3a.gif

Nov 23, 2013 | 2005 Mazda 6

1 Answer

Check engine light code P0741 starting coming around 80K now has 99,000 miles. I was tpld it has to do with torque converter. GM quoted $3500. to repair AMCO $2500 est. I changed transmission fluid and...


PCM make check every now and then . But engine has to meet certain condition. like example ,engine temp,engine speed, engine rpm, and the load on engine and so on
all to say you fix the problem of tcc solenoid stuck or poor performance because you change trans, oil But don't think it will solve any engine light on

Oct 04, 2013 | 2005 Pontiac Vibe

1 Answer

P0750 and P0755 codes on a 2005 Ford Escape, 6 cyl. Codes were pulles with the Check Engine light came on and then the warning light (O/D Off/Transmission) started flashing.


All I will tell you is, that any time you have transmission
issues,you have to stop using the vehicle immediately

It doesn't matter what the situation is with transportation
or appointments,your vehicle has priority over everything

If not, your going to end up pulling it out & your repair bill
will start at $1,500 & go up

Both those codes, as I suspect you know, appear to be
shift solenoids & you don't exactly have a premier trans
to start with,mazda I believe

I would suggest a trans repair shop

Jul 01, 2011 | 2005 Ford Escape

1 Answer

I have a 2005 mazda 6. it was 2 qts low on oil, i added oil, the car ran fine but had a slight rattle. 2 days later, i was sitting at a stoplight and the car died. my mechanic says the engine seized. no...


Hi . Unfortunately it's a common problem with mazda6 engine.When they run low on oil the crank shaft tend to get damaged.And some times people tend to top up oil rather than changing oil between 6000 &10000kms .Yep the engine is seized cost less replacing the engine than repairing it.good luck....

Jan 05, 2011 | 2005 Mazda 6

1 Answer

Check engine light


sounds like an O2 fault poss if it was a hard code the engine light would be stuck on so sounds like another sensor in the circuit is doing two jobs while the sensor that throws the light on has failed get the diagnosic code if any get back to me

May 13, 2010 | 1993 Mazda MX-6

1 Answer

On my 2005 Mazda 6, my engine light is on and the diagnostic code says it's the gas cap..How to I turn the check engine light off


you would need a scan tool to reset it, if it is the gas cap and you fixed the problem with it then the light will go out after 100 miles of driving with a couple of cold starts. if it doesnt go out after a few days of driving then that wasnt the problem.

Mar 10, 2010 | 2004 Mazda 6

1 Answer

O/d light and check engine light blinking


You can reset these codes by disconnecting the negative side of your battery, has to be the negative side, for 5 minutes and then try it. If the light comes back then you may have a problem.

Feb 06, 2010 | 2000 Mazda 626

1 Answer

2005 Nissan Xterra (2wd) check engine light flashes then engine stalls at stop lights, driving fast or slow, puffs a little black smoke when check engine light flashes then stalls. Have to wait a minute...


Take it to a reputable independent repair shop that isn't a chain...that employees Master L-1 Technicians. Chain stores can barely change oil, let alone diagnose complicated issues.

Aug 11, 2017 | 2005 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...