Question about Cars & Trucks

1 Answer

CAR RUNS GREAT FUEL HAND DOEST REGISTER STAYS ON EMTY

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 70 Answers

Most likely a broken wire on tank sensor.

Posted on May 02, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I turn the ignition everything comes on except the fuel pump.The gas hand stays still and does not register.then again it does.


if gas gauge dont work and vechicle wont start fuel pump faulty but check fuel pump fuse or relay first make sure they okay.

Oct 22, 2013 | 2002 Dodge Dakota Club Cab

1 Answer

1993 S-10 Blazer runs great then dies at temp


If you have Code 15, you need a volt meter or you will run into a wall. You measure the coolant resistor ohms when its cold then measure it when the engine is warm.You also have to measure one side for a 5 volt reference.Or better yet when the vehicle reaches operating temperature and begins to stall take the leads of the coolant temperature and jump it together.This tell the ECM your temperature is 266F. If its stays running and doest stall replace temp sensor

Mar 10, 2012 | 1993 Chevrolet S-10 Blazer

1 Answer

Gas gauge goes full emty full emty gaugegenerly reads full but latly its up and down truck runs then wont


You need to test the gauge and the sending unit in the gas tank itself. In most cases I find this is the sending unit in the tank. Unfortunately, that is usually combined with the fuel pump in 1995 and newer vehicles which means you have to replace the whole unit. If you have 2 opening to your tank with wires coming from both you have a separate level sending unit from the fuel pump. If there is only one they are combined. Check for shorts on those wires.

Jul 29, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

2000 s-10 4 cyl. truck runs good gas gadge gose from full to emty with a full tank or emty tank dose not matter? whats the fix!


had the same problem on my 2000 s-10 ,turned out the wire from sending unit had worked loose(bad crimp). The fuel pump had recently been replaced. the connector to the sending unit was different from original . the new pump included the different connector ,but it had to be spliced in .Check connections at tank/fuel pump.Also there were 3 ground connections 1 tank to frame 2 bed to frame on my s-10 hope this helps

Mar 30, 2011 | 2000 Chevrolet S-10

1 Answer

I Have a 1999 f350 Super duty Dually 7.3 Powerstroke. It starts hard in 80 to 90 Deg. weather and runs like it is 20 below. Then when pulling a emty or under a load has no power like id is running on 4...


It could be that you have picked up a batch of dirty fuel that has clogged the gauze input filter that is part ot the fuel pump inside the fuel tank.

Jul 29, 2010 | 1999 Ford F350 Regular Cab

1 Answer

When you start up car gas hand shoot to full and then drop to emty


could be two things,,float in gas tank,,bad fuel gauge, in instarmint ctuster

Apr 05, 2010 | 1999 Pontiac Grand Prix

1 Answer

Faulty Petrol Gauge


Hi there,
It could be 2 things:
1. the fule sender unit is faulty
2. one of the baffles inside the tank has come loose and is interfering with the float.
Either case you'll have to pull the float out to have a look. If you are doing it yourself, make sure youtake great care as you'll be dealing with fuel and this is a high risk work.
cheers.

Apr 22, 2009 | Nissan Hardbody Cars & Trucks

1 Answer

My car doest keep on after i release the key. it turns on but it doesnt stay on


check timing, belt may have slipped and timing is off. also chek fuel pump.

Feb 20, 2009 | 1990 Acura Integra Hatchback

1 Answer

Tank is full but guage says emty


THIS PROBLEM IS CAUSED BY A DEFECTIVE GAS GUAGE SENDING UNIT, U WILL NEED TO PULL THE FUEL TANK AND REPLACE IT.

Feb 11, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...