Question about Ford Cars & Trucks

Open Question

Picture showing camshaft with balance shaft for ford ranger,2002 Pick-Up turbo diesel 2.5. Engin # WLAT286860. CHASSIS N0:MNABSFE401W2126

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

Ad
  • 56 Answers

SOURCE: ford F250 6.0 litre turbo diesel won't start.

check the fuel cut-off switch under the glove box.

Posted on Jul 21, 2009

  • 167 Answers

SOURCE: do i need a turbo timer for an intercooled diesel engin..isuzu...

Yes it pays to have a Turbo timer or let it run for 3 minutes after an outing.
An Intercooler is usually fitted to turbo charged engines.It cools the air entering the engine making it denser,Thats why cars go really well on frosty mornings after they reach running temp.
Hope this helps.

Posted on Aug 02, 2009

  • 1 Answer

SOURCE: why is my 99 ford F450 7.3L turbo diesel blowing

Does any one have a idea a friend here has changed ecm, inj, fuel pump checked conector at fire wall ,fuel and has a short wrecker tow f450 99 and will be going down the road and he says the thing just loses all power and kind of just won't do over 15 to 20mph and lets it sit and he says it will do it again. I am not sure how long it takes but since I don't work on diesels I figured I would have the experts that do if anyone knows it's you guys any help he is in Charlotte NC I can put you with this guy he has had it to all the parts changers and no luck Thanks Mark 704 492 1647

Posted on Mar 02, 2010

melvi_99
  • 387 Answers

SOURCE: 2008 Ford F250 6.4 turbo diesel, have 3 DTC codes

P0087- low pressure fuel system. Fuel pressur valve stock open, Fuel volume control valve stuck close, Leaking fuel injector,P0088- fuel pressure contorl valve stuck close, Fuel rail pressure sensor P2291-all @ at the above, means to say poor fuel quality

Posted on Jun 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Twin cab ford ranger swing but do not start no fuel from diesel pump


check 12 volts reaches the fuel pump
relay or fuse
or replace fuel pump

Apr 26, 2017 | Ford Cars & Trucks

1 Answer

What are the camshaft cap bolt tentions on a 2007 ford ranger 3.0 turbo diesel common rail engine


I looked at info for 99 ford ranger 3.0L engine.
The thrust plate on end of camshaft, the torques for those bolts, 84 inch lbs.
If I misunderstood your post, please excuse?

Nov 04, 2016 | Ford Cars & Trucks

1 Answer

2.5 ranger td 2007 diesel pump timing marks n will da key way on the pump should b same as the timing marks


images for 2.5 ranger td 2007 diesel pump timing marks

Ford ranger 2.5 diesel pump timing marks - Fixya

www.fixya.com/.../t12609400-ford_ranger_2_5_diesel_pump_timing_...
Apr 29, 2012 - SOURCE: need the timing marks for a 3.1 td 5 cyl diesel injectionpump. isusu engine?? have you looked for a 8mm hole in timing gear that ...

Mazda Bravo 2.5 TD 2000 - YouTube

? 10:00
https://www.youtube.com/watch?v=D8zJeouIXfo
Sep 11, 2010 - Uploaded by V8Jagnut
and one other , would a miss timing on the fuel pump cause engine .... The only thing I've ever seen with a Mazda dieselengine was an old Mercury Lynx. ... Ford Ranger Mazda B25002.5TD Servicing Guide Part 2 - Air and .

Oct 29, 2015 | 2006 Ford Ranger

1 Answer

Hie how can I eliminate balance shafts which are worn out badly on a nissan hardbody 3l turbo diesel 4x4


balance shafts are there to remove harmonic vibrations from the engine . to remove the shafts will cause premature failure of the engine
the balance shafts do nothing but balance and do not wear as they have only bearings to hold them staright

Sep 13, 2015 | Nissan Cars & Trucks

1 Answer

I have 2002 Ford ranger 2.3l n I broke two teeth on the harmonic balancer that the sensor reads I assume will this stop the engine from starting?


most definitely
there has to be set pulses for the position sensor to work
normally both the crank position sensor and the cam shaft position sensor work together and send signals to the ECM and if one signal is not in sync with the other , the ecm thinks something is wrong and shuts down the engine.

May 07, 2015 | 2002 Ford Ranger

1 Answer

Ford ranger 2.5 turbo diesel 2004,when engine is running and ticking over,the glow plug sign and the air bag in the control panel flashes alternatley,but does not affect the driving.


hi i have a 2004 2.5 turbo diesel ford ranger ,while driving on the highway a major power loss ocurred now feels like a 1.3 uno cant feel turbo engaging at all i removed the turbo and took it to a specialist he says its fine ,could it be the diesel pump or what else can it be

Apr 13, 2010 | 2004 Ford Ranger

1 Answer

Timing Marks-99 Ford Ranger


Its Dot to Dot.. Crank Pointer Up.. CAm Pointer down.. DOT 2 DOT.. Thank you

Mar 15, 2009 | 1999 Ford Ranger SuperCab

1 Answer

P0340 Code Camshaft Position Sensor



The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Jan 17, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

Balancing a 2 piece drive shaft in place.


no, when taken out should have been marked to go back the same way. when u joints changed did they move freely or were they stiff to move if so that can cause a out of balance problem

Nov 11, 2008 | 2002 Lincoln Navigator

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...