Question about 1993 Ford Probe

1 Answer

I have a 1993 ford probe and someone cut the wiring harness that goes to the ignition to ppput a toggle switch in i want to go back to a key does anyone know what wire goes where there are six of them

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 2,432 Answers

Best to go to ford dealer and get a copy of the wiring circuit , the only sure way i know, unless you have a work shop manual.

Posted on May 03, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my nissan 1400 bakkie runs perfectly until i leave the key in on position so i can only drive with holding the key sightly between start and on whats wrong? not ignition as i bought new one and doe


Sounds like a bad ignition switch. Replace it or do away with the part that feeds 12 volts to the coil
If you can get a wiring diagram for it, find the ignition wire.You could also use a 12 volt test light to find the ignition wire. Cut the ignition wire off the harness under the dash where it goes up the steering column to the ignition switch.Splice onto the end that goes to the coil. The lower end of this harness.
Install a rocker or toggle switch somewhere easily accessible. Preferably a lighted rocker switch. Run a fused 12 volt positive to it, and the ignition wire that goes to the coil. If you use a lighted rocker switch, you'll need a ground wire up to the new switch (so the light will work). When the switch is on, the ignition is on. No more messing around holding the key just right to keep it running.
Or, since the ignition switch you have seems to be defective, take it and have it replaced. There might be a warranty, since a new switch shouldn't work like that. Good luck Garcuda

Nov 29, 2014 | Nissan Cars & Trucks

1 Answer

EF Ford Fairmont 1996, accessories stop when ignition switched to start


Eg wipers work while ignition switched to 'accessories' but stop when key turned to 'start'

I had this issue and took me ages and ages of wire tracing and probing. Your fuse box should have the wiper/windows accessories fuses. If you probe them and they aren't showing voltage, check wiring harness, check wiper motor voltage. My ignition barrel was the fault of all this, everything worked when switched to "accessories", but while the engine was running, the accessories turned off. The bottom of the ignition barrel pushed out, as the factory stopper groove bent out. All I did was cold chisel a dent back into the case. BAM fixed my windows/starting/wipers all in one go.

Nov 16, 2011 | Cars & Trucks

2 Answers

Power decklid won't pull trunk down. Replaced actuator and switch in decklid and the servo in the trunk.. works intermittently


If it works intermittently, you probably have a damaged wire -- my guess would be where the wiring harness goes to the trunk lid. The constant motion of use can damage the wires internally. They still look ok on the outside usually, you'll have to check them electrically (with a meter or test light) The other possibility is damage to the harness that goes to the latch from something moving in the trunk and hitting it. Good luck.

Apr 26, 2010 | 1993 Lincoln Town Car

1 Answer

1994 Ford Probe GT - 1. Key stuck in ignition 2. Hazards on


Hello , I am a locksmith in Az. The Ford, Chevy& Dodge igns up until 2004 all had this problem. You will need a new updated "side-bar free" ignition to cure that problem. If you decied to splice wires , yes it will work, but you will need to be extra EXTRA CAUTIOUS IN RE-ATTACHING WIRES AND MAKE SURE THAT WIRES ARE IDENTICAL IN COLORS. (not yelling) just making sure you understand the importance of this procedure.

Quinn

Jan 23, 2010 | 1994 Ford Probe

1 Answer

I'm working on a 93 probe gt when I turn the ignition I get all the lights, fuel pump, bells but no cranking. Pulled the starter it's good. I can get it to run if I hot wire it from the solenoid to the...


have you replaced the ignition switch? not the key cylinder but the actual electrical switch, they are prone to this type of failure, pull the covers off the steering column and test the switch.

Oct 15, 2009 | 1993 Ford Probe

2 Answers

Ford Ranger will not start


Does the car click when you turn the ignition? If it does, it is probably your starter. If the engine does not turn when you turn the ignition.

Sep 30, 2009 | 1993 Ford Ranger SuperCab

1 Answer

Someone cut tail light wire and i need to know how to fix it


If you can see the cut wires then simply join the same color coordinating wires with a crimping style wire connector that you can purchase from WalMart or any auto parts store. Make sure and strip the plastic casing around the wires on both ends before using the wire connector. After the connector has been crimped to both wires, wrap electrical tape around the connector to seal off from water.

Jun 07, 2009 | 1993 Ford Probe

1 Answer

Wiring diagram


Their are no free car wiring diagrams on the internet. 

Sep 24, 2008 | 1993 Ford Probe

2 Answers

Ford 1993 probe horn


The horn Button at the steering wheel is simply a switch. It grounds out when pushed causing the circuit to close, routing it though the actual  horn under the hood which is sitting there waiting to activate.

Jul 24, 2008 | 1993 Ford Probe

Not finding what you are looking for?
1993 Ford Probe Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...