Question about Cars & Trucks

1 Answer

Where is the shift lock fuse located on a 2001 tacoma prerunner?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,817 Answers

The first thing you do is check your brake lights. The shift lock system solenoid is powered by the brake lights, so no brake light no shift lock activation, it's a safety feature so you can't start the engine without the foot on the brake pedal.

Posted on May 01, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 314 Answers

SOURCE: 2004 Tacoma prerunner hesitates and shakes while

i would check and make sure that the TPS and the MAP sensor are operating properly

Posted on Jul 09, 2009

  • 1857 Answers

SOURCE: Where is the fuse or relay transmission shift

There is no fuse for this. Its possible the brake switch is bad even if the brakes lights work.

Posted on Dec 29, 2009

  • 14036 Answers

SOURCE: How do you tighten belt on a steering pump. Toyota

YOU ADJUST POWER STEERING BELT TENSION BY LOOSEN THE LOCKBOLT AND ADJUSTING BOLT TO IDLER PULLEY.

Posted on Apr 19, 2010

  • 242 Answers

SOURCE: i have a 2001 tacoma prerunner that does not want

With info that you are giving me I only deduct that , maybe your idle control valve is stuck open with carbon buildup, clean the throttle, let some of the carburetor cleaner go to the idle control valve hole then spray gently compressed air in the Idle Valve hole. When you remove the throttle tube to clean the throttle plate you will see a little hole, that is the idle control valve hole.

Posted on Dec 26, 2010

  • 7353 Answers

SOURCE: bank one sensor one

bank one is always the side of the engine where number 1 cylinder is. Right Front (passenger side)

Posted on Sep 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust low idle adaptation on 2005 Tacoma prerunner 4.0


1. Relearn the idle speed by disconnecting the EFI fuse and the ECTS fuse from the under hood fuse box. Leave the fuses out for 2-3 minutes minimum. Reinstall the fuses. Using your finger, push the throttle plates closed completely. Hold the throttle plates closed completely and have a helper turn the ignition switch on. Release the throttle plates as soon as the key is turned on. Reinstall the boot to the throttle body and start the vehicle. Allow the vehicle to idle for 5 minutes. Test drive the vehicle and check for normal idle operation.

Sep 30, 2014 | 2005 Toyota Tacoma PreRunner

1 Answer

Where is fuel filter located 2004 toyota tacoma extra cab prerunner?


If it's a V-6 engine the filter is located underneath the driver's side just inside where the frame is, on the 4 cylinder it's located under the intake manifold near the front of the engine.

Feb 16, 2012 | 2004 Toyota Tacoma

1 Answer

Where is the starter relay for a 1999 Toyota Tacoma located?


hadder: in the engine compartment is a large box which contains fuses and relays. The starter relay is one of ones in the very rear(close to the firewall) It would be the second one in from the engine side and is a 5 pin relay. The same location applies for the four and V-6's.

Aug 12, 2011 | 1999 Toyota Tacoma PreRunner

1 Answer

2002 toyota tacoma 4 door prerunner def. lock. was told it is blowing oil it is on the spark plugs. starts shaking very bad between 45 and 50 mph but not in overdrive. stops shaking at 52 mph. was when in...


2001 Toyota Tacoma Prerunner, 3.4L, 4 door, 2WD, automatic transmission overdrive problem. It's not shifting to overdrive, overdrive button on shifter does not turn light on - on dash. Mileage is 115,xxx.

Sep 07, 2010 | 2002 Toyota Tacoma

1 Answer

Location of the fuel filter on 2000 toyota tacoma 2 wd std cab


Oil filter on a 2000 Toyota Tacoma Prerunner with 6 cylinder IS a screw on filter located on the drivers side front of the engine (just beneath the alternator).

Can't recall the size but, you need a socket with extension to get to the bolts holding the skid pan then, wiggle/lift it from it's hooks. Then, you can either cuss, cuss, cuss while removing the old and installing the new OR, jack the drivers side up 4 to 6 inches ( gives you a bit more wiggle room and keeps you from scraping your elbow to the bone on whatever surface you're working on).

Even then, be ready for a good cussing bout because there still isn't much room.

May 19, 2010 | 2000 Toyota Tacoma PreRunner

1 Answer

My 2001 toyota tacoma prerunner is burning the 10a tail light fuse immediately after i put it in


Then you have a short circuit to ground in this tail lamp wiring which you need to find to stop the fuse burning out. Finding a shorted circuit may not be easy but you can try this, check your trailer electrical connection (if you have one) as these do cause this kind of issue. Faulty wiring to this connector, damage or lost screws can all result in this issue. You may need to follow the rear wiring harness from the cab back to locate anywhere that the wiring has been crushed or rubbed through insulation has occoured and the copper conductor is now touching the body or a ground wire. Check the trailer connector, rear wiring behind the lamp assemblies and the harness where it runs in the chassis. If you have recently has any work done under the vehicle, check this area too..

Nov 09, 2009 | 2001 Toyota Tacoma

1 Answer

Location of fuel filter 2000 prerunner 2.7 engine


In the engine bay, on the firewall, behind the engine if it's a 2.7L I4. It'll be tricky to change due to space constraints.

Oct 29, 2009 | 2000 Toyota Tacoma PreRunner

1 Answer

2002 Toyota Tacoma PARTS of the dashboard very dim.


turn your dimmer switch up it effects those lights and the dashboard

Aug 07, 2009 | 2000 Toyota Tacoma PreRunner

1 Answer

2005 Tacoma Prerunner hard shift after breaking


it sound like your slave cilender is going out

Feb 20, 2009 | 2005 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...