Question about Cars & Trucks

Open Question

How to remove the console - Cars & Trucks

Posted by on

  • Brett Duxbury
    Brett Duxbury May 01, 2017

    Hi Kathleen Bingham, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?
    remove console in what type of vehicle ?
    make & model and year made ??????????????

  • Kathleen Bingham
    Kathleen Bingham May 01, 2017

    yes thank you...I want to remove the console on my hyundai tucson 2006 V6. Yesterday, a pen slipped through the opening the cup holder and the blocked the emergency brake from going down all the way so of course, in a hurry, I forced it..today when i tried to roll down my windows (power windows) NONE would work..so I'm thinking maybe I disconnected a wire in the console that has effected the windows..Thank you so much for your thoughts...Kathleen

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

How do I remove the center console of a Isuzu Ascender


why not read on alldata.com, its all there,
remove a screw?


25402002-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg
  1. Block the wheels to prevent the vehicle from moving.
  2. Remove the rubber ash tray inserts and rubber mat from the console.
  3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
  4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
  5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
  6. Remove the center console retaining screws.
  7. Adjust the parking brake to the full-up, or fully engaged position.
  8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
  9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
  10. Disconnect the electrical connectors, as necessary.
  11. Adjust the parking brake to approximately the halfway position.
  12. Remove the center console from the vehicle.
  13. If replacing the floor console base, remove the following and retain for transfer:
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.
or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.

Feb 05, 2015 | 2006 Isuzu Ascender

1 Answer

Remove center console from 2002 ford explorer. do I have to remove the seats?


I don't think you have to remove the seats. However any nuts, bolt or screws you remove you'll need to keep in case you're replacing the console.

Open the console and at the bottom you'll find two Phillips head screws.

Look at the front of the console, beneath the radio. Next to the coin holder area, is four bolts. Remove the four bolts with a ratchet.

Look at the center part of the console. There are two Phillips-head screws. Remove these with a Phillips screwdriver.

Pull the console upward to unhook it from the floorboard. Remove it from the Ranger. With the console removed, you'll see the mounting brackets for the console and the nuts the screws and bolts go into. It is not necessary to remove these brackets when replacing the console.

Move the replacement console into the cabin. Line up the console with the mounting brackets on the floorboard. The console screw and bolt holes should be lined up with the mounting bracket's nuts.

Hold the console firmly in place with hand. Insert and tighten the two Phillips-head screws in the console storage compartment, and then insert and tighten the four bolts at the front part of the console. Insert and tighten the two Phillips-head screws in the center of the console.

Hope I didn't over explain. Hope this helps.

Jan 29, 2015 | 2002 Ford Explorer

1 Answer

Center console removal


Well, this good to be interesting to say the least, and probably long as well. By my gm. service information your going to need to take out the front bucket seats so the sides of the console can come off.


Remove the left front seat . Refer to Bucket Seat Replacement .



1



Front Floor Console Extension Panel



2



Retainer Clip (Qty: 5) same for right side.



showgif.do?image=1875475





tif.gif








Callout







Component Name






Preliminary Procedure

Remove the right front seat. Refer to Bucket Seat Replacement .







1





Front Floor Console Extension Panel







2





Retainer Clip (Qty: 5)








Front Floor Console Accessory Trim Plate Assembly


Procedure

Use a flat bladed plastic trim tool in order to release the console accessory trim plate from the console assembly.



2



Retainer Clips (Qty: 5)



Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement.



1



Front Floor Console Accessory Housing Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Accessory Housing Assembly


Procedure




  1. Disconnect the electrical connectors.


  2. When replacing the front floor console accessory housing assembly, transfer all necessary components





  1. Remove the rght or left front floor console extension panel. Refer to Front Floor Console Extension Panel Replacement - Right Side or Front Floor Console Extension Panel Replacement - Left Side .


  2. Remove the front floor console cup holder housing. Refer to Front Floor Console Cup Holder Housing Replacement .



1



Front Floor Console Rear Trim Panel Screw (Qty: 1)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Rear Trim Panel



3



Retainer Clip (Qty: 4)


Preliminary Procedures


  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console fillers. Refer to Front Floor Console Filler Replacement .



1



Front Floor Console Armrest Assembly Bolt (Qty: 4)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

9 N?·m (80 lb in)



2



Front Floor Console Armrest Assembly


Procedure

Position the armrest assembly out of the way leaving the electrical harness attached.



3



Front Floor Upper Console Trim Plate


Procedure

Lift the rear of the trim plate first, releasing the retainers securing the trip plate to the console assembly.



4



Retainer Clips (Qty: 4)



Front Floor Console Replacement (Enclave)





showgif.do?image=1858392





tif.gif








Callout







Component Name






Preliminary Procedures




  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console extension panels. Refer to Front Floor Console Extension Panel Replacement - Right Side and Front Floor Console Extension Panel Replacement - Left Side .


  3. Disconnect the automatic transmission range selector lever cable. Refer to Range Selector Lever Cable Replacement .







1





Front Floor Console Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)







2





Front Floor Console Bolt (Qty: 10)




Tip

Before installing the right lower forward bolt, ensure that the console wiring harness is tucked below the fastener location to avoid driving the bolt into the harness.




Tighten

9 N?·m (80 lb in)







3





Front Floor Console Assembly


Procedure



  1. Note location and routing of the front floor console wiring harness prior to removal of the front floor console assembly to ensure proper reinstallation.


  2. Disconnect the electrical connectors.


  3. With the aid of an assistant remove the console assembly from the vehicle.


  4. When replacing the front floor console, transfer all necessary components.





h4hqqpweof7+aaaaaelftksuqmcc

arzs+0tf0j6faaaaaelftksuqmcc

Jan 10, 2015 | 2008 Buick Enclave

1 Answer

How do you disassemble the counsil?


Front Floor Console Replacement Removal Procedure
1. Remove the console trim plate. 2. Remove the left console trim panel. . 3. Remove the right console trim panel. 4. Remove the floor console compartment.
1356712.gif
5. If equipped with an automatic transmission, remove the 4?screws?(1), attaching the console?(2) to the shifter assembly?(3).
1356713.gif
6. If equipped with a manual transmission, use a flat-bladed tool to disengage the retaining tabs?(1) attaching the manual transmission shifter boot assembly?(2) to the console. 7. Remove the manual transmission gear shifter knob, if necessary. 8. Remove the manual transmission shifter boot assembly?(2) from the shifter, if equipped.
1356714.gif
9. Disconnect the console wiring connector?(1) from the inner console.
1356717.gif
10. Remove the two nuts?(1) attaching the floor console?(3) to the vehicle floor. 11. Remove the two screws?(2) attaching the front of the console to the instrument panel assembly. 12. Remove the accessory power receptacle. 13. Lift the rear of the console upward and remove from the vehicle. 14. Remove the floor console armrest hinge, if necessary. 15. Remove the center console end panel.
1356777.gif
16. Remove the screw?(2) attaching the floor console rear air duct?(3) to the floor console?(1). 17. Remove the floor console rear duct?(3) from the floor console?(1). 18. Remove the console storage bin, if necessary. 19. Remove the console lamp. 20. Remove the console compartment lamp switch.

Oct 06, 2011 | 2005 Pontiac GTO

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

Need instructions on how to remove center console to access electric window switch.


Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.
  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

May 04, 2009 | 1986 Chevrolet Corvette

1 Answer

How can i find out my parking brake adjustments on my 2003 ford escape?


Parking Brake Cable Adjustment Vehicle with low series floor console
  1. Remove the floor console front finish panel.
    1. If equipped, remove the manual transmission shift knob by turning counterclockwise.
    1. Remove the floor console front finish panel.
  1. Remove the floor console rear finish panel.
    1. Apply the parking brake.
    1. Remove the floor console rear finish panel.
Vehicle with high series floor console
  1. Remove the floor console finish panel.
    1. Apply the parking brake.
    1. Remove the floor console finish panel.
All vehicles
  1. Remove the adjustment nut clip.
  1. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled.
  1. Confirm the parking brake is applied.
  1. Install the adjustment nut clip.
Vehicle with high series floor console
  1. Install the floor console rear finish panel.
Vehicle with low series floor console
  1. Install the floor console rear finish panel.
  1. Install the floor console front finish panel.
    • If equipped, install the manual transmission shifter knob by turning clockwise.

Jan 21, 2009 | 2003 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...