Question about 2000 Oldsmobile Bravada

Open Question

My 2000 bravada wont start its seems like its not getting fire and ive changed the plug and wires and checked to make sure they was correctly hooked back up

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2000 Oldsmobile Bravada SmartTrak...not sure how

Fan in Auto
Temp where you want it.
Air position in Auto

TEmp control will do the rest for you!

Posted on Nov 13, 2009

Ad
  • 51 Answers

SOURCE: 2000 alero won't start. turns over and fires but wont start

make sure your cap and rotor timing is correct double check spark plug routes (mistakes happen). maybe your timing is off in general.

Posted on Jan 16, 2010

  • 1757 Answers

SOURCE: 2000 OLDS BRAVADA FIRING ORDER DIAGRAM

For the Oldsmobile Bravada 4.3L V6:

Firing Order
:
1-6-5-4-3-2

Cylinders:
......(back)......
|..6..|.......|..5..|
|..4..|.......|..3..|
|..2..|.......|..1..|
......(front)

Distributor Connections:
...........(back)
Coil-> o
6-----> o.......o <-----5
4-----> o.......o <-----1
2-----> o.......o <-----3
...........(front)

Let me now if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on Apr 26, 2010

  • 447 Answers

SOURCE: My 2000 oldsmobile bravada does not want to start

This is kind of a long shot but if it is difficult to start after sitting all night but then starts just fine during the rest of the day then you may be just a pound or two low on fuel pressure. This engine needs a minimum of 60 psi of fuel to start properly. If you have only 59 psi it will crank and crank and finally start but will behave all day long as if nothing was ever wrong. You could also have a leaky fuel regulator or injector that is causing it to be partially flooded when you attempt to start it but usually those problems bothers more after the engine is warmed up. Even some new fuel pumps won't put out the needed 60+ psi and sometimes the fuel pressure regulator can go bad and not allow the pressure to build up to the 60+ psi range. The only true way to know for certain what the actual pressure is to have someone test it with a very accurate test gauge. Hope this helps out a bit and good luck.

Posted on Jul 07, 2010

  • 82 Answers

SOURCE: my 2000 bravada will turn

hi there
If you have fuel pressure the next thing you need to check is if you have spark if there is no spark it will not start hope this helps you thank you and have a great day

Posted on Aug 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 chevy k1500 wont start after changing distributor and rotor


very good but did you check that the no1 piston was on tdc firing before you replaced the distributor . You may be 180degrees out on the firing order.

Apr 09, 2014 | Cars & Trucks

1 Answer

Chevy venture stalled


Compression, spark , timing , fuel for any engine to run. Don't forget a stopped up catalytic convertor will have the same effect as you described. Backfiring of course is fouled plugs, bad plug wires, look for arcing from wires when it is dark outside. If it has a distributor check for cracked cap, had my 91 GMC start backfiring then die due to ignition module inside distributor going bad. It would start back up after it cooled for about 10 minutes.

May 16, 2017 | Cars & Trucks

3 Answers

2000 Bonneville, 3800 wont start after changing wires and plugs


504f87c9-6de3-462d-b669-b739a95f9aca.png
check each wire to be at good spark plug number with the image

Nov 07, 2013 | 2000 Pontiac Bonneville

1 Answer

Changed spark plugs, car turns over but wont start


Double check to make sure you didn't accidentally unplug and censors on the harness. Also check your fuses. for you ignition.

Nov 07, 2013 | 2000 Pontiac Bonneville

1 Answer

CAR WONT START!!! I was driving and the car


Issues are most likely to arise with the spark and fuel (and 90% will be spark), so solving starting and stalling problems should begin there, after you've made a general inspection to make sure all hoses and wires are connected, and that the air filter isn't clogged solid with dirt.
A warning here before we go any further: If you're using an aftermarket distributor cap, rotor, igniter, coil and/or plug wires, be aware that quality is variable and they are unlikely to be anywhere near OEM standard, even if they're sold as "premium". There's a reason such parts are cheaper. Poor-quality aftermarket parts can (will) cause their own problems that can greatly complicate diagnosis of starting problems. For the little extra cost, new OEM is always the safest. Also, never crank the engine with the plug wires removed, or with the distributor cap off, except for brief (very brief) testing purposes. Doing so can overheat and damage the ignition coil.

Aug 14, 2013 | 2000 Mitsubishi Diamante

1 Answer

I can't seem to start my 84 Oldsmobile cutlass


DID YOU GAP PLUGS CORRECTLY? CHECK TO MAKE SURE SPARK PLUG WIRES ARE IN RIGHT FIRING ORDER QUESTION DOES ENGINE TURN OVER LIKE IT WANTS TO START???? CHECK ALL FUSES SOME HAVE STARTER RELAY FUSES ALSO MAKE SURE TRANSMISSION IS FIRMLY IS PARK MAY HAVE A STARTER SAFETY RELAY CAR WONT START UNLESS PARK IS ACHIEVED.....GOOD LUCK

May 09, 2012 | 1985 Oldsmobile Cutlass Supreme

1 Answer

2000 alero won't start. turns over and fires but wont start


make sure your cap and rotor timing is correct double check spark plug routes (mistakes happen). maybe your timing is off in general.

Jan 16, 2010 | 2000 Oldsmobile Alero

1 Answer

96 accord ex wont start


Firing sequence is off or plug wires are not connected completely. check the firing order, to the plugs and make sure all connections are on (you will have to push down on top of boot pretty hard to get a good connection)

If it is turing over jump starting isn't gonig to help (you battery if fine unless you have drained all the power from it)

Feb 02, 2009 | 1996 Honda Accord

Not finding what you are looking for?
2000 Oldsmobile Bravada Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...