Question about Cars & Trucks

Open Question

Hello I have a eumig mark s 701 IS IT THE SAME AS THE 709 PLEASE

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need a claw arm for a EUMIG MARK 822 projector.

Sorry we have no parts for sale here.

Jun 27, 2017 | Cars & Trucks

1 Answer

Hello, I just bought a 2002 dodge caravan se and my boyfriend tried to put motor oil in it because the light inside was on but he put alittle to much and it just reached the m on the max marking, now I'm...

If the oil is on the max mark then that is ok for it to be there but if you are still worried then remove the sump drain plug gently and drain off just a little bit. Personally the max mark is a better place to have the oil level than the L- min mark

Jul 21, 2013 | 2002 Dodge Caravan

1 Answer

I have the timming belt off of my 1993 geo metro the timming markes are off' i need to know how to realighn the the crank and cam gears.

Hello hjolana: My name is Roger and i will help you. I have attached a picture of the timing marks.The camshaft mark aligns with the mark at top of cover behind the cam gear. The lower mark aligns with the notch on the block and the crankshaft key way is at 12:00 o'clock. See the picture. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Rogerrogerf1_48.jpg

Aug 13, 2011 | 1993 Geo Metro

1 Answer

What is the timing diagram for a 2.3 liter ford engine

Hello j bailey478: My name is Roger and I will help you; I have attached a picture of the timing marks for the engine you requested. Should you need further help please just ask. Please rate the answer received. Thank You for using and trusting Fix Ya. Rogerrogerf1_6.jpg

Dec 18, 2010 | 1996 Mazda Pickup

1 Answer

I need a diagram of the engine timing marks for a 1995 S10 Blazer. Can anyone provide?

Hello Friend:

Yes i can tell you how to set your Timing Marks.

Your Top Gear the Cam Shaft Sprocket you want the timing Mark you'll want it to be Pointing Down .it won't be completly straight Down but Very close to it.

You'll want your Lower Sprocket (Crank Shaft) Point Upward .Until both Cam And Crank Shaft Marks Ar Directly in Line with the Other.

As Long s you Have those 2-Marks Meeting Straight Across from each Other,You will be Set t Top Dead Center.

Meaning the your number 1- Piston Should be up and on the Compression Stroke, Not on the Power Stroke but Compression.

Either Way Sir if you got em Lined up like I was talking About you'll be Fine.

This will get your Timing Gears Lined up Properly,.

Thank You Sir for Using Fixya Please let me know the Quality of my Solution by Voting for me.

Thanks Again From d_hubbs

Aug 17, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

How do you set the timing on a 1.9 liter 98 model Saturn

Hello loraina: My name is Roger and I will help you. The timing on your 1.9 engine is set by timing of the cam and crankshaft gears in the engine. There are no timing marks or reference marks to check.Engine timing is controlled by the PCM. Should You need further help please just ask. Please rate the answer you received. Thank You for using Fix Ya. Roger

Jun 26, 2010 | 1998 Saturn SL

1 Answer

How do u set the ignition timing i have 2 marks then have 3 marks after it

Hello! Timing is set using the RED mark...It is the middle mark in the equally spaced group of three marks...Set with engine at normal operating temperature...All vacuum lines connected...670 RPM...


May 04, 2010 | 1994 Honda Civic

1 Answer

Inst of a timing chaine 1953 dodge pic up flat head 6 what marks do i use to line up the gears

Hello tdalbo: My name is Roger and I can help. According to 1956 Motor repair manual. Locate the timing marks on both gears. The camshaft and crankshaft Marks face each other mark to mark when installed. I tried to print the picture but it comes out to dark to see. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Oct 30, 2009 | Dodge Pickup Cars & Trucks

1 Answer

Need to now where timing marks are located on 1997 chrysler sebring coupe 2.5Ljust replaced waterpump & timing belt and car will not start I didnot turn crank or cams when rplacing belt

Hello carolnaes: My name is Roger and I will help. The picture of the timing marks are attached. I will caution though that Mitchell repair calls this a interference motor. Meaning if the engine turns over with the belt off. The valves of the engine can and may be damaged. I also checked All Data and they said it could possible cause valve damage. Should you need further help please just ask. Please rate the quality of your answer. Thank You for using Fix Ya. Roger39f6dc5.jpg

Oct 17, 2009 | 1997 Chrysler Sebring

1 Answer

Where can i find the timing marks on 1998 ford escort zx2 ?

Hello pamgolmon: My name is Roger and i will answer your question. The 2-0 dual cam engine is a interference engine. This means if the engine jumps time at the timing belt. It will bend the valves. As for the timing marks on the camshafts. Their are no marks to be located. To set the timing marks on this engine requires special tools. This makes it expensive for not only the do it yourself mechanic but also the repair shops also. If the valves were bent you must pull the head for the repairs also.
I know this is not the answer you were hoping for but it is the only answer to give. Please rate the quality of the answer as this way we know your answer was correct. Please just ask if you need further help. Thank You for using Fix Ya. Roger

Sep 09, 2009 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides