Question about Cars & Trucks

Open Question

Diesel pipe assembly at the back of the pump where is number one cylinder pipe colt 2.8 d

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 73 Answers

SOURCE: timing

Look at the front of the gears. there should be small notches in the gears . line them up and you will be timing the pump

Posted on Feb 04, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix...?a timing of colt 2.500 diesel


, proper way is to use diesel timing light and set pump canter to correct position(assuming good pump ) , close enough way , accelerate to half rpm , turn pump canter (angle) till smoke out tailpipe turns from black to white(or vice versa) then move slightly back , tighten pump down and retest , might be needed to go back and forth a few times to get it just perfect

Jul 29, 2015 | Cars & Trucks

1 Answer

QD32 engine how do I know number 1 on injector pump


if the injector pump is an inline pump ( where all the injector pipes are arranged along the top of the pump the no 1 injector is the line closest to the front of the engine . If it is a rotary pump ( where the injector lines mare arranged in a circle at the back of the pump no 1 will be either at the 10 oclock or 2 oclock position. As the injector lines are hard and bent for each piston then the line from no 1 injector will point to the no1 position on the pump regardless of how many cylinders there are. If it is a common rail diesel then it doesn't matter because the injection timing is electronic and set from the crank shaft position sensor.

Nov 27, 2014 | Cars & Trucks

1 Answer

Air in the diesel pipes


check all pipes from your pump to your injectors are tight start at no1 cylinder slacken pipe on injector end while a friend cranks engine on key repeat on oyher cylinders this should bleed all air from system

Nov 17, 2013 | Renault R18 Cars & Trucks

1 Answer

Hi. I have mazda drifter wl turbo 2,5 diesel. Cam belt snapped and broke 2 valves. I replaced the complete head and serviced the pump and replaced new injector nozzles. Also did big ends and small end...


incorrect ignition point for the injectors
diesels ignition point is around 22 degrees btdc for pumps or from the crank sensor if common rail ( information of year or pump or common rail not included )
if it is a pump with pipes to injectors , you have the timing incorrect

Jul 02, 2017 | Cars & Trucks

1 Answer

Colt 2.8 timing marks


l need to know the specs how to set the diesel pump timing on colt 2.8turbo diesel 2003 model

Apr 18, 2012 | Mitsubishi Cars & Trucks

1 Answer

How to replace a waterpump on a 2001 olds alero 2.4 cam


Water pump is driven by timing chain idler and is mounted on the rear of the timing chain housing. Disconnect the neg. battery cable. Drain cooling system. Disconnect oxygen sensor connector.
Remove upper exhaust manifould heat sheild. Remove exhaust manifold brace. Remove lower exhaust manifold heat sheild. Loosen manifold to exhaust manifold spring loaded nuts. Remove radiator outlet pipe to water pump coverbolts. Disconnect exhaust pipe from manifold.
Pull down on the exhaust pipe to disconnect it from exhaust manifold bolts. Disconnect outlet pipe from oil pan and transaxle. If equipped with manual tranaxle, remove exhaust maifold brace. Leave lower radiator hose attached and pull down on radiator out look pipe to disengauge from water pump. Leave outlet pipe hanging.
Lower vehicle. Remove exhaustmanifold to cylinder head nuts. Remove exhaust manifold to cylinder head nuts. Remove manifould. Remove timing chain front cover. Remove timing chain tensioner. Remove bolts bolts securing water pump cover to cylinder block. Remove water pump to timing chain housing nuts. Remove water pump attaching nuts. Remove water pump and cover assembly. Separate componets as necessary.
WHEN INSTALLING WATER PUMP MAKE SURE YOU FOLLOW THE TIGHTENING SEQUENCES THAT AFFECT SEALING. My frist one I messed up and broke the pump so becarful.
Installation
If cover was separated from body during removal, join this componets with a new gasket and hand tighten bolts. Apply bearing grease to splines of water pump drive. Set body and assemble into position.
Install and hand tighten bolts securing cover to cylinder block. Install and hand tighten bolts securing cover to cylinder block. Installand hand tighten nuts securing body to timing chain housing. Lubracate outlet pipe "O" ring with antifreeze. (I use RTV) Connect outlet pipe. Install and hand tighten bolts. Tighten bolts and nuts to specification in the following sequence. I'll ad the torque spec. at the end but this is where if you tighten out of order something will break.
pump assembly to timing chain housing nuts.
pump cover to pump body bolts
pump cover to cylinder block bolts (Bottom Bolt First)
outlet pipe to cover bolts
To complete installation reverse removel procedure.
Torque specs are 19 in. or 26mm all except water pump cover bolts which are 124 in or 14Nm
I never torque the bolts just make sure there done in the right order.

Oct 19, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

How do i change a water pump in a 97 grand am with a 2.4 litre engine


2.4L Engine
See Figure 3
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Disconnect the oxygen sensor wiring.
  4. Remove the upper exhaust manifold heat shield.
  5. Raise and safely support the front end of the vehicle securely on jackstands.
  6. Remove the exhaust manifold brace bolt.
  7. Unbolt and remove the lower exhaust manifold heat shield.
  8. Break loose the manifold-to-exhaust pipe spring loaded nuts.
  9. Unbolt the radiator outlet pipe assembly from the water pump cover.
  10. Disconnect the exhaust pipe from the manifold.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
Do not rotate the flex coupling more than 4°. this could damage the component.
  1. Separate the radiator outlet pipe from the oil pan and transaxle.
    1. On manual transaxle, remove the exhaust manifold brace.

  2. Next, leave the lower radiator hose attached and pull down on the outlet pipe to detach it from the water pump. Allow the outlet pipe to hang.
  3. Lower the vehicle.
  4. Remove the exhaust manifold-to-cylinder head nuts.
  5. Extract the manifold, seals and gaskets.
  6. Remove the timing chain cover. Refer to the procedure later on in this section.
  7. Remove the timing chain tensioner. Refer to Timing Chain removal later in this section.
  8. Unbolt the water pump from the cylinder block.
  9. Extract the pump assembly-to-timing chain housing nuts.
  10. Remove the water pump and cover assembly.
  11. Separate the pump from the cover.
  12. Clean all mating surfaces of gaskets and sealant materials.

To install:
Prior to installing the water pump, read the entire procedure. Pay special attention to the tightening sequence to avoid component damage and ensure a proper seal.
  1. Attach the water pump to the cover and hand-tighten the components.
  2. Lubricate the splines of the water pump drive with chassis grease or equivalent, then install the pump and cover assembly. Hand tighten the cover-to-block bolts.
  3. Install the pump-to-chain housing nuts and hand-tighten.
  4. Lubricate the O-ring on the radiator outlet pipe with an anti-freeze solution and slide the pipe into the water pump cover, install and hand-tighten the bolts.
  5. With the specified gaps, tighten in sequence as follows:
    1. Pump assembly-to-chain housing nuts
    2. Pump cover-to-pump assembly
    3. Cover-to-block, bottom bolt first
    4. Radiator outlet pipe assembly-to-cover

  6. Install the exhaust manifold using new gaskets.
  7. Install the manifold-to-cylinder head nuts, follow the tightening sequence and tighten to specifications.
  8. Raise and support the front of the vehicle.
  9. Index the exhaust manifold-to-exhaust pipe flange bolts.
    1. Turn bolt bolts in evenly to avoid cocking the exhaust pipe and binding the bolts. Turn the bolts in until they are fully seated.

  10. Install and secure the radiator outlet pipe to the transaxle and oil pan.

On manual transaxles, install the exhaust manifold brace.
  1. Install the timing chain tensioner and chain cover.
  2. Attach the lower heat shield.
  3. Lower the vehicle.
  4. Attach the exhaust manifold brace. Tighten the manifold-to-exhaust pipe nuts to specification.
  5. Attach and secure the upper heat shield.
  6. Connect the oxygen sensor wiring.
  7. Fill the radiator with coolant water mixture until it reaches the heater hose coolant outlet, then install the hose and continue to fill. This will assist with the complete cylinder block fill.
  8. Connect the negative battery cable.
  9. Start the engine and top off the cooling system and check for leaks.
ec6ae2e.jpg

Dec 28, 2009 | 1997 Pontiac Grand Am

1 Answer

WHERE THE WATER PUMP IS LOCATED on a 2.3 liter 4 cylinder quad hoc


it is driven off the timing chain, here is how you replace it
2.3L And 2.4L OHC Engines
  • Disconnect the oxygen sensor harness connector
  • Raise the vehicle and support it securely on jackstands
  • Remove the exhaust manifold brace and loosen the exhaust manifold bolts
  • Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine
  • Remove the exhaust manifold pipe from the exhaust manifold
  • Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging
  • Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head
  • Remove the timing chain cover from the engine
  • Remove the timing chain tensioner
  • Remove the water pump cover bolts from the engine block and the timing chain housing
  • Remove the water pump bolts and separate the assembly from the housing


Dec 01, 2009 | 1994 Pontiac Grand Am

2 Answers

How to replace the water pump on 1993 oldsmoblie achieva.


2.4 enigine is the harder of the 3 enignes. it will need a timing chain to be removed and a coolant tube in the back of the engine to be removed. this job on the book calls for almost 7 hours.

if its 3.3 or 3100 its alot easier.

3100 is just 4 10mm pulley bolts and 5 or 6 small 8mm water pump bolts.

3.3 is alittle more work, but same concept as 3100 engine. more owkr only cause its in a tighter area.

good luck,
michael

Apr 29, 2009 | Oldsmobile Achieva Cars & Trucks

1 Answer

Timing


Look at the front of the gears. there should be small notches in the gears . line them up and you will be timing the pump

Feb 02, 2009 | 2006 Mitsubishi Colt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...