Question about Jeep Wrangler

Open Question

03 wrangler completely shut down while mud riding.. battery, connections and fusses are good... it does nothing when I turn the key, not even interior lights.?

03 wrangler with 4.0

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
JustJeeps
  • 74 Answers

SOURCE: WOnt run over - battery good - can turn it over but jumping the starter

if the battery is good and you jump the starter she should run otherwise you may have a sensor issue, try to get a hold of a code reader and see if any codes have popped up..

Posted on Nov 21, 2008

Ad
mp3stud
  • 15 Answers

SOURCE: 03 ford expedition interior lights stay on and door ajar reads

This is a very common problem with Fords. I have one that was doing this as well. What works for most people is pretty much what you have tried - spraying inside the latch all over with WD40 Until it's coming out the bottom of the door. If this fails to work, the switch probably needs replaced. The switch is located inside the door near the latch. It should be pretty easy to find once you have the door panel off. Look for the wires leading to it. A new switch is usually very inexpensive, but may have to be purchased through your local Ford dealer. If you're not comfortable taking the door panel off, a mechanic should be able to do this repair for you in less than an hour of shop time.

Posted on Jun 05, 2009

  • 347 Answers

SOURCE: Engine shut down on freeway. Good battery, low oil

low oil boiling water sometime automatically stop the engine for further damage. stop the engine wait for sometime. fill up oil/water. check fuse/switches for engine/lights/dimmer. re start.

Posted on Oct 04, 2009

SOURCE: bria2004 fore expedition, will not

Check that the battery connections and clean and tight. Check to dee if the connections on the starter and clean and tight also. If all this is good then remove the starter and have it checked.

Posted on Nov 20, 2010

czaa
  • 4536 Answers

SOURCE: 2005 Acura TL. The

u shud scan vehicle 1st--a flaw in the wiring harness may be present or solenoids etc cud be staying on--go in engine area and chec the maxifuses that connect to alternator-if burnt then batt wouldnt charge--secure a repair manual

Posted on Feb 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 97 ford expedition. When I turn the key...nothing...not even a click, is that the solenoid, or is there a starter relay that could be bad.


Do you get anything from the dash (lights, gauges..etc.) when you turn the key or is it completely dead? Check the battery connection and also the starter. Sometimes the battery is on its last leg and will provide enough for lights but won't turn it over.

Jan 31, 2013 | 1997 Ford Expedition

1 Answer

03 wrangler wont start


A problem on the ignotion?
____________-
wifi obd tool for ipad iphone

Oct 08, 2012 | 2003 Jeep Wrangler

1 Answer

New starter, new relay and new battery...problem is...when I shut off engine and 30 minutes later went out to start again the key turned and nothing happened...it was like the battery was completely dead....


I suspect you have a loose or corroded connection. you should be able to check voltage at relay and if good, jump across from cable coming from battery to terminal from ignition switch. or u can bypass the relay completely by using a jumper cable to go from battery pos to output cable on relay that goes to starter.

Mar 25, 2011 | 1992 Ford Explorer

1 Answer

No start...2000 Wrangler 4.0liter, automatic.


To me it sounds like you have weak battery. Hook up a meter and check voltage. should be over 12v, then turn key on. should maintain 12v. then crank. If the voltage goes below 11v cranking the battery is bad. Be sure to test the battery. Not the cables. Then tst the cables. You may have good voltage just touching the battery and you may have low voltage touching the terminals which would indicate a dirty connections.

Jul 27, 2010 | 2000 Jeep Wrangler

1 Answer

03 Wrangler will not turn over/start


Pull off the battery cables from the terminals, take a bit of sandpaper, and run the **** over the terminals. Then, mix a 25/75 Arm&Hammer/Water mixture, take a rag, and run that on one terminal, then the other, try not to drip water. Take sandpaper again, and run it over the terminals again, until they are fully shiny. Now, do the same things on the inside of the battery connectors. Make sure they clamp down well. That should do it. If not, make sure all the wires are good and solidly connected. Finally, get a voltmeter, and test between the block and the positive connector/terminal. Should read ~12.4-6V. (12.4 = bit low, but I figured if it's trying to go through a corroded connector or a short, it will be a bit low)

Jul 24, 2010 | 2002 Jeep Wrangler

1 Answer

2006 Jeep Wrangler electrical problem and wont start


its called, riding your fuckn peddal to the medal syndrome....nepoleaon comp. ect....

Sep 29, 2009 | 2006 Jeep Wrangler

1 Answer

Dosn't turn over


First, verify the actual voltage at the battery with a voltmeter. Second, make sure terminal connections are clean and secure at both terminals and the other ends of the battery cables as well. Also find the source of the noise you hear...If it's coming from a relay, find out which one now, before it completely fails and is more dificult to locate. (do not change it till you verify all connections are good and actual voltage is good.
There are a few more tests you can do but do these first.

Jun 02, 2009 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

I have a 88 jeep wrangler. Ok what happed was when i started driving it the other day i heard something break and the motor shut off. After looking under the jeep i saw the rod coming off the throttle...


That rod may have pulled of wire going to starter, or ground strap in that area. No headlights, nothing? Disconnect (+) positive connection at battery for now, and have a look along the path the rod may have taken for a cut or broken wire or strap.

Jan 12, 2009 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...