Question about Cars & Trucks

Open Question

Slide out will not come in without a little help at first

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to disengage the locking mechanism on my sliding door. It sounds like it unlatches but will not open. HELP PLEASE!


You will need to remove the inside panel from the inside of van to access the cables/linkage to see if they are disconnected, try opening from the inside button, also check lock mechanism to see if it is unlocking both electrically and manually. If you slammed real hard you may have done something to the latch.

Jan 28, 2015 | 2000 Chrysler Town & Country

1 Answer

1997 dodge 2500 ram4/4....71,000 miles. Run fine without slide in camper on it. Put camper on it and it run fine until it's gone maybe even as little as 40 miles then starts to loose power and bla


Has the exhaust ( catalytic converter) been check for proper flow? I would try a test pipe to by-pass converter and see if that helps. You used to be able to buy them, but a good exhaust shop can make one pretty quick, and then try it.

Feb 19, 2013 | Dodge Cars & Trucks

1 Answer

Sliding doors bottom slider wheels are out of track, but top and middle track wheels are still in place. how can I get the rollers back in the track without braking or taking the door completely apart?


if you check out the track, It actually has a slot part way down, that the wheels can slide back into, Not sure how the 99 wheels mount, but the 97 you can loosen them from the underside of the door, for a little extra play

Jul 11, 2011 | 1999 Dodge Caravan

2 Answers

My brake rotors are stuck because of rust how should i get them off?


theres pullers but theres costy, the best way is to spray WD-40 and let it sit for a min, then with a mallet smack them little by little turning the rotor al ittle at time and theyll loosen up. if youre not plaing on reusing them again then use a hammer. haha thats the way my crew get them out.

Aug 03, 2010 | 1997 Buick Skylark

1 Answer

How to put side doors back on the track so they can open and close without any problems


this happened on my 87 stretch caravan once I had to remove the bottom slider track and slip the little wheel back in the track and then bolt track back on one half and then slide door to get other half

Dec 19, 2009 | 1999 Chevrolet Venture

2 Answers

How do you remove the wiper arm on a 94 Dodge Ram 1500? The arm will not fully extend with the hood open or closed but maybe that doesn't matter. Can't get to the wiper motor without removing the arms to...


throw a grenade at it and hopefully the arms will fly off, whatever happened to a nut on a threaded flange to hold wipers on. No wonder imports own the market.

Aug 15, 2009 | Dodge Ram 1500 Cars & Trucks

2 Answers

Trouble removeing the fuel filter


You need what's called a "fuel line disconnect tool". It's held in place by a spring, and the tool slides in the opening to release the spring. Harbor freight sells sets of them for about $15.00. Other than that, you would need something to wrap around your fuel line, and slide into the opening to release the spring.

May 30, 2009 | 1995 Ford Thunderbird

1 Answer

Replace an ignition lock without the key on a 1976 Volare


you take off the stearing wheel and under it there is a spot that you slide a flat head into and push a little tab on the lock cylender to release. its kinda hard to find but good luck

Dec 29, 2008 | 1990 Jeep Cherokee Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...