Question about Ford Cars & Trucks

Open Question

Relays are hot and Ford crown Vic 87 shuts off in gear coming to stop

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Where is the fuse panel on a 1985 Ford Crown Vic located?

Local Ford dealership service department provide answer on location of the fuse panel. Fuse panel is located directly under the steering column. The cover panel is held by two screws and the power antenna swithch locking ring must be removed.

thank you all for you assistance,

Posted on Jul 01, 2008

  • 2 Answers

SOURCE: 1999 Ford Crown Vic transmission problems

check u joints and drive shaft for weights hope this works

Posted on Sep 06, 2008

chrischronic
  • 235 Answers

SOURCE: itman arm removal - 1995 ford crown vic

remove the nut then buy a pitman arm puller at your local autoparts store, this tool will pull the pitman arm from the steering box.

Posted on Jan 22, 2009

jaysonemanme
  • 500 Answers

SOURCE: 1995 crown vic gear problems/gear shift wont lock

most likely the shift tube bushings are bad- you may have also lost a few screws in the shift tube or they could just be loose. you have to pull the steernig column down to inspect/repair it.

Posted on May 31, 2009

  • 439 Answers

SOURCE: 1988 Ford Crown Vic Strange Idle

When you turn the key on does the check engine light come on? If not it may be burned out. It sounds like a MAP sensor or an O2 sensor is bad. I would suggest taking it to autozone as they do free diagnostic and seeing if a code comes up. If it is a sensor it should, if not it may be the idle sensor not reading right in the ECU. More than likely it is one of the sensors though.

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

'99 Ford Crown Vic LX: #12 30A Maxi fuse blows seconds after starting or ignition turned on.


i had this problem with my 1999 jeep grand cherokee laredo with the brake lights it kept popping fuses right after the ignition was turned on try putting a higher amp fuse in place of the old one that keeps blowing then check for shorts to the starter and check grounds and wires and also the transmission issue check the fluid and then if the fluid is fine change the transmission filter the filter may have not gotten replaced when the transmission was rebuilt and may be clogged or dirty

Oct 04, 2012 | 2002 Ford Crown Victoria

1 Answer

2004 Crown Vic tran whines in low gear only, took ...


It's normal on the AOD transmissions. Their first gear uses straight cut gear and thus has the whining noise. Gear 2, 3 and 4 are helical gears and thus quiet.

May 20, 2010 | 2004 Ford Crown Victoria

1 Answer

1999 FORD CROWN VIC. 4.6 - PROBLEM, NOISE


This is caused by the IAC valve. Over time the valve becomes gummy and inoperative. Get it replaced and the problem is solved. IAC stands for idle air control, hence the stalling concern.

Oct 17, 2009 | 1999 Ford Crown Victoria

1 Answer

1988 Ford Crown Vic Strange Idle (Getting Worse)


i am trying to install an aftermarket temperature guage with capillary tube into my 1988 crown victoria ltd 5.0 efi. where does the capillary tube mount?

Jun 27, 2009 | 1988 Ford Crown Victoria

1 Answer

1988 Ford Crown Vic Strange Idle


When you turn the key on does the check engine light come on? If not it may be burned out. It sounds like a MAP sensor or an O2 sensor is bad. I would suggest taking it to autozone as they do free diagnostic and seeing if a code comes up. If it is a sensor it should, if not it may be the idle sensor not reading right in the ECU. More than likely it is one of the sensors though.

Jun 23, 2009 | 1998 Ford Crown Victoria

2 Answers

1985 Ford Crown Vic won't shift sometimes. Seems


Have he transmission drained and the screens cleaned

Jun 05, 2009 | 1995 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...