Question about Cars & Trucks

Open Question

Color codes 4wd colorado selector switch and diagram for a 2011 chevy colorado

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 03 Chevy Tahoe Z71 - 4wd not functioning

my son has one and his did that and it was a fuse he put a new one in and it is working good now

Posted on Jan 22, 2009

468 Chevelle
  • 81 Answers

SOURCE: 4wd selector switch quit

Most of the time, the selector switch is bad.

Posted on Mar 26, 2009

stevenhurc
  • 450 Answers

SOURCE: electric 4WD selector switch on dash does not select/deselect 4WD. I wish to manually shift the selector at the gearbox if this is possible.

by swapping vaccum hoses on front diff shift on fly unit you can get out of 4wd or vise versa or by removing and sliding sleeve ring inside diff tube over, check range selection detent switch on this unit it is a on/off switch.these fail often

Posted on May 28, 2009

  • 599 Answers

SOURCE: chevy colorado code 420 and 496 whats the problem?

code 420= Catalyst system efficiency below threshold(bank 1) code 496=Evaporative emission system-high purge flow. Hope this helps if you need more help get back to me Thanks Ray

Posted on Feb 15, 2010

  • 239 Answers

SOURCE: I need the factory audio color code diagram for a

2006 Chevrolet Colorado Car Audio Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. The accessory turn-on is controlled by the lan serial network. Run a wire to the fuse box or ignition switch harness.
Car Radio Ground Wire: Black/White
Car Radio Illumination Wire: N/A
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

pls rate

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know how to reset the service reminder on a 2015 isuzu d-max 2.5 twin turbo?


I would ask the dealer to do this but here is what I show to get the light reset. This is courtesy of expert Techmecho

If the tech 2 device is indicating the code for 4wd module then it has to be replaced.Get the module and its connections checked before going to replace the module.If the module connections are getting short or loose then getting the connections repaired solves the problem.But most probably when it shows module problem,the module has to be replaced.The actual testing procedure is as follows:--- If you have an ODBII code reader, you can check if there are any codes stored in the ECU. There is also a diagnostics mode you can go into for transfer case issues:

1. Warm up the engine. Turn it off.
2. Turn the ignition switch on and off at least twice, then turn the ignition switch to off.
3. Shift into park.
4. Turn the 4WD selector to Auto.
5. Turn the ignition switch to on. Do not start engine.
6. Is the 4WD warning lamp on? Continue if no.
7. Shift into reverse.
8. Turn the 4WD selector to 2WD, Auto, 2WD.
9. Shift into drive.
10. Turn the 4WD selector to 4H, Auto, 4H.
11. Shift into neutral.
12. Turn the 4WD selector to Auto.
13. Shift into park.
14. The 4WD indicator light will come on for 2.5 seconds, then go out. It will then flash a series of times to represent a one or two digit code, with half-second delays within a number and 1 second delay between numbers. e.g. to represent the code 23, it will flash twice with 0.5 seconds between flashes, wait a second, then flash three times with 0.5 seconds between them.Get it rechecked again by disconnecting the 4wd module and reconnecting again,. --------------------Thank you.

May 12, 2016 | Isuzu Cars & Trucks

1 Answer

Could some one please tell me where the reverse light switch on the gearbox is on a holden rodeo ra 05 thank you


07 Rodeo Reverse light switch...where is it? - Rodeo,Colorado and ...

forum.australia4wd.com > ... > Rodeo,Colorado and DMAX Technical

Nov 5, 2011 - 7 posts - ‎4 authors
posted in Rodeo,Colorado and DMAX Technical: My reversing lights ... switch as per workshop manual..could someone throw me a bone here...thanks. ... Started By rodeo5 , Nov 05 2011 04:35 PM ... My 4WD:RA 07 Rodeo; State:NSW ... would say the reverse switch would be on the gear box some where ...

Locate & Repair 96' Pajero Reverse Light Switch - YouTube

? 1:45
https://www.youtube.com/watch?v=osie5D_m-dA
Nov 12, 2010 - Uploaded by TwoMagadan
Locate & Repair 96' Pajero Reverse Light Switch ... Replacing ABack Up Light Switch On A Manual ...

Dec 14, 2015 | Holden Cars & Trucks

1 Answer

To who ever can HELP !! This is a electric junction block on a Chevy 4wd 1990 -95 with a 5.7 !! I would like to know where they go , color code's ect ect !! New harness , Old one burnt ! I "Don't want


If the new harness is an oem match then you can just go to autozone or where ever, and get a haynes manual. It has the wiring diagrams with color codes in the last section. Good luck.

Feb 04, 2013 | Cars & Trucks

1 Answer

How to set the 4x4 electronic selector switch on a jimmy 2002


4X4

On these issue, there are few solved help links for troubleshooting the issue easily.-------

Click the link below: ---

No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

-----------

4X4 Truck makes roaring noise in the front end?

http://schematicsdiagram.blogspot.com/2012/01/4x4-truck-makes-roaring-noise-in-front.html

-------------

Car will not go into 4WD high or 4WD low?


http://schematicsdiagram.blogspot.com/2011/12/car-will-not-go-into-4wd-high-or-4wd.html

--------------

No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

------------

4 wheel drive system will not disengage?

http://technoanswers.blogspot.com/2012/01/4-wheel-drive-system-will-not-disengage.html

----------

4WD light is flashing and beeping? NO 4WD high?

http://schematicsdiagram.blogspot.in/2012/02/4wd-light-is-flashing-and-beeping-no.html

----------

2002 Jeep Wrangler: 4WD Idiot Light is ON?

http://technoanswers.blogspot.in/2012/06/2002-jeep-wrangler-4wd-idiot-light-is.html

----------

Traction control switch will not engage on 4WD High or Low

http://whoisbyme.blogspot.com/2012/10/traction-control-switch-will-not-engage.html

-----------

4WD light flashing and 4WD will engage after few minutes

http://repairhelpcenter.blogspot.com/2012/10/4wd-light-flashing-and-4wd-will-engage.html

------------

2008 Toyota Tundra: 4x4 Wheel Drive Light is Flashing?

http://technoanswers.blogspot.in/2012/05/2008-toyota-tundra-4x4-wheel-drive.html

----------

4x4 front differential will not engage the axle on ford?

http://technoanswers.blogspot.in/2012/02/4x4-front-differential-will-not-engage.html

-------

4x4 will not engage on Ford F150?

http://technoanswers.blogspot.in/2012/02/4x4-will-not-engage-on-ford-f150.html

-------------

Dodge Ram 4x4 light keeps flashing

4X4 LOW LIGHT IS FLASHING ON DASH

http://technoanswers.blogspot.in/2012/09/dodge-ram-4x4-light-keeps-flashing.html

----------

Ford 4x4 front wheels will not engage?

http://technoanswers.blogspot.in/2012/02/ford-4x4-front-wheels-will-not-engage.html

-------------

These details will help.

Thanks.

Nov 28, 2012 | GMC Cars & Trucks

1 Answer

1998 Chevy Suburban - service 4wd light comes on after running 4x4 for 2 mins


Well it could be the selector switch, but I doubt it.
Generally, the service light means something is not working that the computer controls. Solenoids and valves are a couple of possibilities.
The transfer case is shifted by solenoids commanded by the body computer based on the switch position on the dash.
You should be able to have a shop scan the body computer for trouble codes and proceed from there.
A basic code reader may not access the body computer.

Jul 05, 2012 | 1999 GMC Suburban

1 Answer

My isuzu dmax 4x4 manual (year model 2004) have a problem . . . "CHECK 4WD" warning light is always on. isuzu service shop tells me that the 4wd module and actuator needs to be replaced upon...


If the tech 2 device is indicating the code for 4wd module then it has to be replaced.Get the module and its connections checked before going to replace the module.If the module connections are getting short or loose then getting the connections repaired solves the problem.But most probably when it shows module problem,the module has to be replaced.The actual testing procedure is as follows:--- If you have an ODBII code reader, you can check if there are any codes stored in the ECU. There is also a diagnostics mode you can go into for transfer case issues:

1. Warm up the engine. Turn it off.
2. Turn the ignition switch on and off at least twice, then turn the ignition switch to off.
3. Shift into park.
4. Turn the 4WD selector to Auto.
5. Turn the ignition switch to on. Do not start engine.
6. Is the 4WD warning lamp on? Continue if no.
7. Shift into reverse.
8. Turn the 4WD selector to 2WD, Auto, 2WD.
9. Shift into drive.
10. Turn the 4WD selector to 4H, Auto, 4H.
11. Shift into neutral.
12. Turn the 4WD selector to Auto.
13. Shift into park.
14. The 4WD indicator light will come on for 2.5 seconds, then go out. It will then flash a series of times to represent a one or two digit code, with half-second delays within a number and 1 second delay between numbers. e.g. to represent the code 23, it will flash twice with 0.5 seconds between flashes, wait a second, then flash three times with 0.5 seconds between them.Get it rechecked again by disconnecting the 4wd module and reconnecting again,. --------------------Thank you.

Jan 24, 2011 | Isuzu Pickup Cars & Trucks

1 Answer

My 4wd will not lock. tried it in park, and neutral. and when i pull up to a stop the idle dies down to 500 rpm. its the push button 4wd the light just flashes when pushed. thought it would be a vacuum...


The most common problem with these would be the transfer case actuator motor or also called the selector, this is what controls the 4wd at trnsfer case, the only other thing would be the button controls they go bad also, you should have the compuetr scanned for any stored codes, the codes will tell you where the problem would be, for example if the computer sees a problem it will turn on a 4wd light or check engine light and sometimes wont turn the light on depending, anyway it stores a code with the problem, example a scan tool is connect to truck connector and computer is scanned for codes and lets say theres a code like p1269 selector motor high voltage, now that code would mean theres a problem in that system,

Dec 28, 2010 | 2005 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...