Question about Cars & Trucks

Open Question

Cylinder head torque and sequence for 4jh1 engine

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

MNfisherman
  • 11896 Answers

SOURCE: Replacing the Cylinder head on a QR20 engine

Hello. I can help you out. Just need to know if it is 2x4 or 4x4 and what liter size is this engine?
You can go to autozone.com and register for free and you will get full free online repair manual.
Just let me know.

Posted on Nov 15, 2009

  • 3640 Answers

SOURCE: i need the engine torque specs for 99 chevy malibu

99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Posted on Sep 07, 2010

alicantecoli
  • 22114 Answers

SOURCE: Head Cylinder Bolt Torque Spec and sequence. In

well according to my alldata book its 30nm then slacken 90? and tighten again 90? ,---Well in all honesty i cannot see this being done on a assembly line at three engines a minute where they are pulled down at once with one big air driven socket machine so here what i would do and its old school in fact it may even be older than me which i doubt ,anyway all jokes aside i would pull down first with a rachet in sequence and this invoilves the first bolt in the middle then the one above it then do one each side alternativly easy so you start in the middle and work your way out left then right left then right and so on ,after pulling them down with a rachet this will apply about 30/35lbs ,then use the breaker bar and pull them down again till i feel it stretch the bolts but as your not me you do as i say not as i do ,so set torque wrench to 55lbs and pull them down in order again ,then coffee break and thats compulsory now up the setting to 65lbs and pull them down again and that should do you ,you should not need to pull them down after so many miles this is not a 1959 morris a series engine but a VW state of the art piece of kit

Posted on Feb 17, 2011

ZJLimited
  • 17970 Answers

SOURCE: 99 Honda civic 1.6 engine

Tighten the cylinder head bolts to their final torque specification in two steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts.

  1. Step 1: Tighten each bolt to 22 ft. lbs. (30 Nm).
  2. Step 2: Tighten each bolt to 61 ft. lbs. (85 Nm).

zjlimited_1681.jpg

Fig. Cylinder head bolt loosening sequence - 1.6L (B16A2) engines (click image for zoom)

Hope helps.

Posted on Aug 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head to engine block torque sequence and ft lbs


    images for Cylinder head to engine block torque and ...
    More images for Cylinder head to engine block torque and sequence

    Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

    boxwrench.net/specs/chevy_sb.htm
    their specs. Click Here! 3/8 Connecting Rod Bolt, Engine Oil, 45 ft-lbs. 11/32 Connecting Rod Bolt, Engine Oil, 35 ft-lbs. Cylinder Heads. Engine oil. (blind hole).

    [PDF]

Nov 29, 2015 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Head bolt sequence and torque values on a 1999 Chevy 3.1L engine


if the 8th number om your VIN is a "J" then this is the correct prossess 3.1LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

if the 8th number on your VIN is a "M" then this is the correct prossess 3.8LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

Oct 12, 2011 | 1999 Chevrolet Malibu

1 Answer

I need the tork spec on 1998 Buick 3800 block for the cylinder head.


hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.


0996b43f8021ae77.jpg

Jun 18, 2011 | 1998 Buick LeSabre

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Want to know the amount of torque pressure do i use when tightening the head bolts, and whats the sequence?


To install:

0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head bolt torque sequence-3.8L engine

  1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
    1. Step 1: 37 ft. lbs. (50 Nm).
    2. Step 2: Plus 120 degree turn.
To install:

0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

  1. Install the cylinder head with a new gasket.
  2. Apply thread sealer to the head bolts.
  3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

Dec 16, 2010 | 2002 Pontiac Grand Prix

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    1 Answer

    Torque specs for cylinder heads 4.9 v8 engine (NOT NORTHSTAR) cadillac.


    5850a5e.jpg

    Fig. Cylinder head torque sequence-4.5L and 4.9L engines (not Nothstar, this is 4.6L)

    1. Tighten cylinder head bolts, in sequence, to 38 ft. lbs. (50 Nm).
    2. Tighten cylinder head bolts, in sequence, to 68 ft. lbs. (90 Nm).
    3. Tighten No. 1, 3 and 4 cylinder head bolts to 90 ft. lbs. (120 Nm).

    Hope this helps (remember rated).

    Aug 12, 2010 | 1991 Cadillac Eldorado

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    1 Answer

    Need to know cylinder head bolt torque specs


    Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

    Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

    Not finding what you are looking for?

    Open Questions:

    0 Answers

    who do i contact to sue gm? after the n.h.t,s.a told gm on 5-23-73 to recall all 1993 saturns gm refused 29 days later i was in a accident that the n.h.t.s.a wanted recalled for a serious saftey problem i suffered a permanent tramatic brain injury and i wrote a letter to mary barra gmsc-e-o.she handed my letter to a jeffery koppy gms lead counsel who replied by a letter to me that was the old gm and because we filled bankruptcy in 2009 the new gmis not taking any futher action in regards to your letter.it took the feds to get gm to finally get the car recalled on 8-10 93 while i was still in the hospital.it gets worst i was a employee for gm at the time.because of my head injury i can't ever work again. i still had 17 years to work for gm and to get my 30 years to retire which was to be may of 2010.instead i had to retire a little after the accident.the day after accident iwas supposed to sign my transfer papers to another gm plant in michigan i was employed at their wentzville mo. plant because i was in a coma for 3 weeks and in the hospital 3 months that transfer never happened and the house we had at the time of accident was all ready sold. we had to get a lawyer so we could remain there. because my one car accident happened so close to where we lived.it happened on the i-70 expressway in warren county in the city of warrenton mo. all our neighbors knew about it. i was told by my doctors to try and do phyical therapy as much as possible.so my wife took me for a walk almost every day.but all our neighbors knew of what happened to me they just staired at me every day.it made me feel like a freak.so we sold the house and moved to the country.and if all that wasn't bad enough when my youngest daughter finished nursing school she asked me if i would co sign a loan for her in 2002 for a new car i still got my gm discount and because my brain wasn't right i told her to go to the gm dealer in the city i lived in because the sales-man was a very good man. and over the years we bought new cars from him i felt we were good friends.the car my daughter bought was a lemon from the time she bought it.it had nothing to do with the salesman or dealer. it was a 2002 chevy malibu.well one day she gave a friend a ride home and as she pulled into friends driveway the ignition just turned off.like it did to those 124 people who died because of a problem gm knew about for a long time. my daughters ignition failed in 2004 so she had the car towed to the closest dealer .they said the ignition was bad and said she needed a new one so she told them to go go ahead a replace it even gm had long knew of the problem she had to pay to get it replaced.then if you's can believe this about 10 years later i think it was 2013 or 2014 she got a recall letter telling her that the gm dealer put in another bad ignition.try keep sending her recall letters.but with gm almost killing her dad plus alot of other people wih cars with bad ignitions. she said theres no way gm will tought her car as usual it wasn't running any ways.so it just sat there and she got tired of looking at it and she just called the junk yard i forget how much she got but said she was just glad it was gone and could never hurt anybody ever again.but i'm not dead yet and i still want gm to pay me for what they did to me.as far as i'm concerned gm should be forced to stop making cars.think of all those children who lost their mother or another family member because of gm.i guess so many companys are out for the most money than can make their using defective parts. before i sign off i would like to say the plant i worked at in wentzville mo.had the most inspectors and process assurance inspectors that it almost impossible for something to slip by.i can see if a car rolls out missing a nut or bolt from time to time but there is no reason anything saftey related to ever be missed,from what i found out about the saturn car that almost killed me the bad positive battery cable that shorted out every thing in the car like air bags and abs brakes with no air bags to deploy thats why i was ejected head first out thru the front windshield.i'll bet it hurt alot but doctors said i was knocked out instantly.BUT just because i was in a coma my wife who is a nurse said i was thrashing around moaning that they kept giving me alot of morphine shots.so i'm very tired now using one finger to type on computer.so before yous buy a new car make damn sure there aren't any recalls on it jay teffer signing off.watch what car you decide to buy!!!!!!!!!

    Sep 20, 2017 | Saturn Cars & Trucks

    Cars & Trucks Logo

    Related Topics:

    15 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...