Question about Lincoln Cars & Trucks

1 Answer

Do a 2005 lincoln ls v8 have blend doors or dccv.?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 14,398 Answers

It has DCCV.

Posted on May 02, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
harley9701ha
  • 424 Answers

SOURCE: A/C blowing hot air in 2005 Lincoln LS

It could be the dccv or the evap. discharge sensor,driver's temp sensor or pass temp sensor. Without hooking up a tester to read pids there is no way to tell. I would recommend going to someone that has the ids tester to read pids. good luck.

Posted on Aug 01, 2009

SOURCE: 2002 LS: aHow do I fill radiator in my V8 Lincoln LS...

First- to drain ,you can reach the drain valve,from the pass side,if you lay on the ground and reach up to the radiator. You do not even have to raise the vehicle up
Second- mix Yellow GO5 Coolant about 50/50 or 60/40. Do not use Green in a Ford or Orange GM
To Fill- Remove the front two plastic screw type buttons,from the engine cover
-Remove the cover
The radiator cap is on the front of engine,on top,it is plastic
Remove cap and that is your fill point
Run engine to warm and get thermostat open,as you would with any vehicle
Top off coolant,replace cap
VERY IMPORTANT-next to the Power Brake Booster,and just under it,is a BLEEDER HOSE;to let air out of system. Turn screw slot ,only a little,DO NOT REMOVE SCREW. When coolant runs out close.
Fill-Degas Bottle,to full line,with coolant.
Check the next couple days on resevoir level ( Degas Bottle)

Posted on May 06, 2010

ZJLimited
  • 17970 Answers

SOURCE: placement of heater hoses on

Check this procedure to Removal & Installation

  1. Disconnect the battery ground cable.
  2. Drain the radiator.
  3. For the 3.9L engine: remove the auxiliary coolant pump.
  4. Disconnect the connector located at the end of the coolant valve harness pigtail.
    NOTE The top heater hose has a green identifying mark to match the hose on the dual coolant flow valve. If mark is not visible, identify the hoses for location. This will aid in the correct installation of the hose assemblies.
    NOTE Hose assemblies shown with components removed for clarity.
  5. Disconnect the three quick-disconnect couplings from the coolant control valve hoses.

    zjlimited_321.jpg

    Fig. The location of the three quick-disconnect couplings

  6. Raise the vehicle.
  7. Remove the coolant valve assembly mounting bolt and the nut.
  8. Raise the valve and disconnect the coolant supply and return lines.
  9. Remove the bolts and remove the coolant valve mounting bracket.
To install:
  1. Make sure that the heater hoses are installed in the correct position.
  2. Lubricate the coolant hoses with MERPOL® meeting Ford specification.
  3. Check for correct hose installation by verifying DATC system operation.
  4. Replace the coolant valve mounting bracket.

    zjlimited_322.jpg

    Fig. The torque specifications of the coolant valve mounting bracket

  5. Connect the coolant supply and return lines.
  6. Replace the coolant valve assembly mounting bolt and the nut.

    zjlimited_323.jpg

    Fig. The torque specifications of the coolant valve assembly

  7. Connect the three quick-disconnect couplings to the coolant control valve hoses.
  8. Connect the connector located at the end of the coolant valve harness pigtail.
  9. For the 3.9L engine: replace the auxiliary coolant pump.
  10. Fill the radiator.
continue...

Posted on Dec 28, 2010

saa_aa
  • 241 Answers

SOURCE: where is the dccv located on a 2000 Lincoln ls

on the passenger side front of the engine compartment, below the ABS pump near the radiator."

Posted on Nov 21, 2011

emissionwiz
  • 77499 Answers

SOURCE: does a 2003 engine 3.9 v8 lincoln ls fit a 2001 lincoln ls ?

Yes both years used that engine.

Posted on Jul 12, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Repairing the blend door on 2001 lincoln ls v6


Lincoln LS has no blend door. You repair the DCCV down near the bottom of radiator. don-ohio

Dec 24, 2016 | 2001 Lincoln LS

1 Answer

2006 Lincoln Navigator. I have replaced driver side blend door actuator. I am getting power to it. Tried the 9 volt battery. Not getting heat to driver side.


Probably the DCCV has quit working. (DUAL CLIMATE CONTROL VALVE). Might be located near radiator? Splits out the heat to the heater cores. don-ohio

Dec 19, 2016 | Lincoln Cars & Trucks

2 Answers

2001 Lincoln ls v6 warm air on one side of car


It's the dual climate control valve also known as DCCV. Very common problem with th LS. You are looking at $500 labor included to replace it. It is a real pain to DIY.

Feb 02, 2015 | 2001 Lincoln LS

1 Answer

What is a 'bad dccv'


DCCV stands for Dual Climate Control Valve. It is used in the LS instead of the blend door and controls the flow of coolant to the heater core. It is a common issue with this car (either shorting out or clogging). How did you determine that it was bad?

Aug 07, 2014 | 2002 Lincoln LS

1 Answer

My 2001 lincoln ls has no heat


Have it checked for a broken blend door actuator shaft.

Jan 06, 2013 | 2001 Lincoln LS

1 Answer

Whre's the location of Mass Airflow Sensor in a 2005 Lincoln LS, V8?


Located in the air intake tube drivers side of vehicle. In Line with air filter housing top. Most of the time mass air flow sensors get debris inside them from an unsecured air filter housing. Sometimes they are tough to clamp housing back correctly

Dec 19, 2012 | 2005 Lincoln LS

2 Answers

Air conditioner blowing hot air


Blowing hot air when set to A/C is almost always a stuck blend door, dead blend door actuator, or a cracked or disconnected blend door actuator vacuum line. The blend door is inside the a/c ducting under the dash, but the actuator will be accessible outside the ducting.

Jul 05, 2010 | 2000 Lincoln LS

1 Answer

A/C blowing hot air in 2005 Lincoln LS


It could be the dccv or the evap. discharge sensor,driver's temp sensor or pass temp sensor. Without hooking up a tester to read pids there is no way to tell. I would recommend going to someone that has the ids tester to read pids. good luck.

Jul 27, 2009 | 2004 Lincoln LS

1 Answer

Lincoln lse 2005 ac blowing hot air on left side!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


If your LS is blowing hot air on one side of the dash and cold on the other the problem most likely is the Dual Coolant Control Valve. The DCCV is used to control cabin temperature. This valve is mounted down low on the passenger side of the radiator fan shroud, and has 3 coolant hoses connected to it. This valve if found to be faulty will need to be replaced to correct the condition.

Jun 23, 2009 | 2005 Lincoln LS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

fordexpert

Level 3 Expert

5623 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...