Question about Fiat Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
Posted on Feb 07, 2009
Go to an auto parts store and get a haynes auto repair manual for your car, about $17.00, it shows some illustrations, but gives a step by step procedure on how to remove and install, good luck.
Posted on Feb 25, 2009
Posted on Nov 16, 2009
Testimonial: "Thank you."
Are you sure you have correct timing? its definetly a fule problem, if timing is good then turn your key to the on position and try to listin for the fule pump to prime. While the key is in on position go to fuel rail, there is a valve on fule rail called sharader valve. Get a small screw driver and press valve in to check if car has fule pressure. if pressure is present then it is incorrect timing or possible bad cam sensor.
Posted on Mar 01, 2010
Even I had this problem. After sometime engaging gear was difficult. There are two reasons. First, it could be leakage of servo fuel/brake fluid from the master cylinder on the clutch side or it could be due to the wear of the pressure plate.
Posted on Apr 27, 2010
Tips for a great answer:
Aug 19, 2016 | 2007 Fiat Palio II
Jan 19, 2016 | 2004 Honda CR-V
May 08, 2015 | Fiat Palio Cars & Trucks
Aug 01, 2014 | 2005 Fiat Palio
Jul 15, 2014 | 2005 Fiat Palio
Jun 08, 2014 | 2008 Fiat Palio 1.2
Jan 30, 2014 | Cars & Trucks
Jan 21, 2014 | Cars & Trucks
Jan 06, 2014 | 2008 Fiat Palio 1.2
The engine and transmission in this cars drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPEDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM
Jul 19, 2012 | Fiat Palio Cars & Trucks
18 people viewed this question
Usually answered in minutes!