Question about Cars & Trucks

1 Answer

Will changing the ignition switch fix the backup ligts

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Cars & Trucks Expert
  • 139 Answers

No but replacing the bulbs might help and check to see if there is power going back to there

Posted on May 04, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is backup light switch on 01 impala


Backup Lamps
The B/U LAMP fuse in the RH I/P fuse block supplies battery positive voltage to the switch terminal of the backup lamps relay. The DIC/RKE fuse supplies battery positive voltage to the backup lamps relay coil terminal. When you place the gear selector lever in the REVERSE position, the powertrain control module (PCM) sends a class 2 message to the body control module (BCM). When these conditions occur, the BCM energizes the reverse lamp relay control circuit, closing the switch contacts, the current flows from the reverse lamp relay switch to the backup lamps. The backup lamps are grounded at G302.

There is alot involved in turn on the back up lights .
DTC B2552
Circuit Description
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamp relay control circuit which energizes the backup lamp relay.

2
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, command the backup lamp relay ON and OFF.
Does the backup lamp relay turn ON and OFF with each command?
YES - Go to Diagnostic Aids
NO - Go to Step 3

DTC B2553
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamps relay control circuit which energizes the backup lamp relay.
Turn the ignition ON.
Shift the gear selector lever to the REVERSE position.
Do the backup lamps turn ON?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Remove the backup lamps relay.
Connect a test lamp between the battery positive supply voltage circuit of the switched side of the backup lamp relay and ground.
Does the test lamp illuminate?
Before replacing parts you may not need , take your vehicle to a qualified repair shop .

Aug 16, 2016 | 2001 Chevrolet Impala

1 Answer

Brake ligts dodn't work and the tailights do


check your brake light switch on the brake pedal

Dec 19, 2012 | 2000 Jeep Grand Cherokee

1 Answer

Backup ligt swich is stuck in close position how do i fix it


replace it would be what I would do. sounds like it's defective.

Sep 27, 2012 | Chevrolet Suburban Cars & Trucks

1 Answer

I need fix the hazard ligts & turn ligts I check all fuses but now I want see the harnes diagram


Those are both driven by a relay built into the hazard switch. Replace the switch and everything will work again.

Jul 21, 2010 | 1995 Volkswagen Jetta

1 Answer

I have 95 ford f150 with the tail ligts stuck on


you need to change the brakelight switch its located on the back of the pedal and also your flasher relay may need replacement!

Jan 05, 2010 | 1996 Ford F150 Regular Cab

2 Answers

I want to install aux. backup lights and not wiring them to the jeeps backup ligts. I don't understand the switch. It has three prongs on the back The diagram shows one is power coming from the relay one...


What diagram? What switch? Are you using a switch that salready in the Jeep, or a switch that you bought? You really need a relay to handle th ecurrent of the lights. The relay will have 4 terminals, The relay is really just a remote switch. Let the relay take the power, not the switch. Buy a relay for fog lights and it should have a diagram you can use.

Dec 19, 2009 | 2004 Jeep Wrangler

2 Answers

Wont start


you should be seeing a steady security light ligt up on the dash what you need to do is below the dask or where the old ignition switch is you should see two grey or white wires you will need to find out what the restiance of the chip was that was in your car before, then go to radio shack and put the resistor between the two wires

Jul 10, 2008 | 1992 Buick LeSabre

4 Answers

Ignition switch, tumbler core.


the switch is straight in front of the driver side.




Jun 21, 2008 | 1998 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...