Question about Cars & Trucks

Open Question

How to assemble hd50 fastener I need a diagram can you help

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WERE CAN I GET A DIAGRAM SHOWING THE FASTENING LOCATIONS FOR 2008 HYUNDIA ACCENT HATCHBACK REAR BUMPER COVER


Hello mbrown2331,

Below is an image showing the rear bumper assembly and it's fastener location.

netvan_119.png

I hope this helps.

Regards,

netvan

Jul 23, 2011 | Hyundai Accent Cars & Trucks

1 Answer

I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


  1. Release hood latch and open hood.
  2. Remove the headlamp assemblies.
  3. Hoist vehicle and support with safety stands.
  4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
  5. Remove front wheels.
  6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Fig. 1 133387737
Fig. 2 133387738

  1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
  2. Disconnect fog lamp wire connectors, if necessary.
  3. Lower vehicle.
  4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
  5. Remove bumper fascia from vehicle.
INSTALLATION


  1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
  2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
  3. Hoist vehicle and support with safety stands.
  4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
  5. Install front wheelhouse splash shields fasteners.
  6. Install front wheels.
  7. Connect fog lamp wire connectors, if necessary.
  8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
  9. Lower the vehicle.
  10. Install the headlamp assemblies.

Jan 02, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

Where is the location of the horn on a 1998 chevy cavalier


I believe the horn is located behind the passenger side headlight assembly. There is a pocket in that area where it is mounted. To gain access you will have to remove the headlight assembly. There is a shroud/cover that goes the whole length under the hood, there is a series of plastic fasteners that hold that cover in place. You will need to pop up center of fastener then the whole fastener will come out. There should be two 12 or 13 mm bolts that hold the headlight assembly to the vehicle. The side marker is part of that assembly I believe. If it is not, there is a tab that helps hold the side marker and headlight assembly together. After you remove the assembly the horn should be visible. Good luck.

Dec 30, 2010 | 1998 Chevrolet Cavalier

1 Answer

Need a diagram of the fastening of the driver's


no pattern just assemble it the way you took it off. Not much in books on this but a picture. I f you have taken many off you will see this . You just have to try most just unclip and then if clips stay in the door you have to retunr them to the cover a lot of times you will have a few screws one behind door handle one by mirror cover and one in behind the entry lamp center of the door and also older gm's one under the arm rest and then even older a couple screws in the lower carpeted panel. and some you take off the door handle and put tool to push out windeow crank parallel with crank handle. and very hold units unscrew the door lock thingy left top. now do repairs and put back together the way you took apart .

Jan 03, 2010 | 1998 Pontiac Grand Am

1 Answer

Where is the horn located under the hood of a 2005 gmc canyon


Horn Replacement Removal Procedure

    1375741.gif
    tif.gif
  1. Remove the grille. Refer to Grille Replacement .
  2. Disconnect the horn assembly electrical connector.
  3. Remove the bolt that retains the horn assembly to the radiator support.
  4. Remove the horn assembly from the body.
Installation Procedure

    1375741.gif
    tif.gif
  1. Install the horn assembly to the radiator support.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the bolt that retains the horn assembly to the radiator support.
  4. Tighten
    Tighten the bolt to 10 N·m (88 lb in).
  5. Connect the horn assembly electrical connector.
  6. Install the grille. Refer to Grille Replacement .

Nov 07, 2009 | 2005 GMC Canyon

1 Answer

I have a 1996 Cadillac Seville SLS and I want to remove the radio and a website said I would just have to pull the trim around the radio and heater out and it would expose screws that would allow me to...


  • Remove the heater and A/C control and radio bracket fasteners.
  • Partially remove the radio and A/C control assembly.
  • Disconnect the electrical connectors from the radio and A/C control assembly.
  • Remove the radio and A/C control assembly.

  • 288103.gif
    tif.gif
  • Remove the radio retaining nuts.
  • Remove the radio from the radio bracket.
  • Installation Procedure Install the radio to the radio bracket.

    288103.gif

      tif.gif
      Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    Install the radio retaining nuts.
      Tighten
      Tighten the radio retaining nuts to 10 N·m (88 lb in).

      287815.gif
      tif.gif
    Partially install the radio and A/C control assembly.
    Connect the electrical connectors to the radio and A/C control assembly.
    Install the radio and A/C control assembly.
    Install the heater and A/C control and radio bracket fasteners.
    Install the console trim plate. Refer to Console Trim Plate Replacement in Instrument Panel, Gauges and Console.
    Install the instrument panel center trim plate. Refer to Instrument Panel Center Trim Panel Replacement in Instrument Panel, Gauges and Console.

    Jun 29, 2009 | 2001 Cadillac DeVille

    1 Answer

    "where is the Horn Location for 2001 Chevrolet Malibu"


    Horn Replacement Removal Procedure
    1. Remove the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.
      794212.gif
      tif.gif
    2. Disconnect the horn electrical connector.
    3. Remove the horn bracket bolt.
    4. Remove the horn from the front frame rail.
    Installation Procedure

      794212.gif
      tif.gif
    1. Position the horn to the front frame rail. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    2. Install the horn bracket bolt. Tighten
      Tighten the bolt to 10 N·m (89 lb in).
    3. Connect the horn electrical connector.
    4. Install the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.

    May 17, 2009 | 2001 Chevrolet Malibu

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    16 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    78267 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14405 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...