Question about Dodge Cars & Trucks

1 Answer

How do you change wheel bearing hub assembly for 2007 Dodge Caliber xlt

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 5,617 Answers

You need big socket could be #32 or #34 for the drive shaft, there is three bolts could be #13 or something else.have to prey out or hammer out. clean good old dirt.Don't torque more than 100 lbs!!! drive shaft.

Posted on Apr 30, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Dodge Avenger wheel hub replacement


The front bearing comes as a hub assembly, so you should be able to unbolt it from the spindle. You still have to take the axle shaft out.

Jun 03, 2013 | 2008 Dodge Avenger

1 Answer

How to change a front wheel bearing on a 2007 toyota tacoma 2 wheel drive pickup truck


The bearing & hub is a whole assembly for this model, start by removing the brake calipers, the removing the rotors" a couple taps with the hammer should loosen it" , after removing the rotors the hub & bearing assembly is held on by 4 #17 bolts, after you get the hud and bearing assembly off you will need a tool called a bearing split plate ,to split the hub and bearing off each other. Now you should have the new bearing assembly ,inner wheel seal, and hub set together" this is when you need a press". Press the hub onto the new bearing assembly.And thats it! Its ready to go back on the way you took it off.

Mar 02, 2013 | Cars & Trucks

1 Answer

How do iI remove the front wheel bearing?


The front wheel bearings on your Dodge Dakota allow the wheels to spin freely on the axle spindle. These sealed bearings may cause noise once they wear out, develop a pit on the races, bends and other damage that interfere with wheel performance. However, the front bearings form a single assembly with the wheel hubs and they should be replaced as a single unit. Fortunately, installing a new assembly is not a difficult process.

  1. Removing the Hub/Bearing Assembly
    • Before raising the front wheel(s), loosen the half shaft nut using an axle nut socket. Then remove the wheel/tire assembly and the half shaft nut. If your particular Dakota model comes equipped with an Anti-lock Bake System (ABS) sensor, remove the sensor form its bracket and move it aside.

      Now you are ready to remove the brake caliper and rotor. Make sure to secure the caliper to the coil spring using a piece of heavy wire. Do not let it hanging by the brake line to avoid damage to the brake hose attached to the caliper. With the caliper and rotor out of the way, you have access to the hub/bearing assembly mounting bolts.

      On some models, you can only access the hub/bearing mounting bolts through the holes in front of the hub/bearing assembly. Rotate the assembly by hand as you loosen and remove the mounting bolts. Once you remove the bolts, you can detach the hub/bearing from the steering knuckle and halfshaft. If the bearing assembly seems stuck to the halfshaft, use a 3 jaw gear puller to remove it.


May 31, 2011 | 2004 Dodge Dakota

1 Answer

2004 F-150 4X4 XLT EXT CAB 5.4L NEED FRONT WHEEL HUB ASSEMBLY DIAGRAM


  1. n0051415.gif
  1. Item
Part Number Description 1 W706540-S900 Axle-to-wheel hub nut (4x4 only)
Removal Note 2 - Wheel speed sensor harness connector
Removal Note 3 2027 Anchor plate bolt (2 required) 4 - Brake caliper, pads and anchor plate
Removal Note 5 1125 Brake disc 6 1107 Wheel hub-to-wheel knuckle bolts 7 1104 Wheel bearing and hub assembly
Removal Note 8 N642567-S36 Tie-rod end-to-wheel knuckle nut 9 W707254-S427 Lower ball joint-to-wheel knuckle nut 10 W520215-S427 Upper ball joint-to-wheel knuckle nut 11 3K185 Wheel knuckle
Installation Note 12 W710279 Integrated wheel and bolt (3 required)


Mar 07, 2011 | 2004 Ford F150

1 Answer

I have a 2007 grand caravan front wheel drive that needs a new rear bearing hub assembly. I have removed all except the assembly and it will not budge. Is there anything I can use to remove the hub other...


CHRYSLER WARNED AGAINST NOT USING A SLIDE HAMMER PULLER UNLESS YOU ARE GOING TO REPLACE REAR HUB AND BEARING ASSEMBLY.WHEN REPLACING HUB AND BEARING ASSEMBLY THEY HAS TO BE PRESSED OUT.

Sep 21, 2010 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

1 Answer

On my 2001 Dodge Ram 1500 5.2 2WD, I just found out that I have to change the front hubs if I want to replace the front wheel bearings. How insane is that! What can I do to have a front hub that I can...


buy an older truck to answer question all newer model vehicles have gone to a hub/flange bearing assembly these bearing setups handle loads without or very minimum variance, when you go into a cornering situation these bearing setups give you a steady and consistent track thus a better handling vehicle now instead of cleaning and repacing tose old cone and race style bearings you just unbolt hub assembly and any related abs sensors and bolt on new

Mar 24, 2010 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

Working on 2007 Dodge caliber XLT; mirrors (both)


Have you found problem with your caliber mirrors not working?I replaced both mirrors/switch and fuses still not working either. turned to see if others have this problem and their fixes.I did reset cars electrical system also like someone suggested and still not working.

Oct 18, 2009 | 2007 Dodge Caliber SRT4 Hatchback

1 Answer

Wheel bearing


u have to take the hub off. and press the wheel bearing out. it takes alittle time to do bc u have to take your rotor and brake assembly off to get to the hub.

Jun 25, 2008 | 2001 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...